Transient performance study of a brushless doubly fed twin stator induction generator

This paper presents theoretical, simulation, and experimental study of the brushless doubly fed twin stator induction generator (BDFTSIG) dynamics under vector control based on the orientation on the power machine stator flux. A complex transfer function is derived which links the control current and power winding current space vectors in the field coordinates. Based on this result, the transient response of the BDFTSIG to step changes in the control current is examined theoretically. The oscillatory transients are explained in detail and linked to control flux transients triggered whenever operation point of the generator is changed. Furthermore, BDFTSIG operation with closed loop control of the power machine active and reactive powers is examined theoretically and experimentally. It is shown that in the closed loop operation, the system damping may be reduced so that the PI controller gains must be properly selected to achieve a good transient response.     

酚醛树脂复合板在热连轧机中的应用

重点分析了现有F7机架出口导卫装置的情况。原导卫材料是由铸钢制造 ,由于摩擦和高温常常引起热连轧带钢表面划伤 ,根据现场实际情况用酚醛树脂复合板替代铸钢导卫装置。实践表明 ,这种改造即可行又可靠 ,并取得了好的效果     

钕电解阳极过电位的测定

用慢扫描示波法测定了钕电解的阳极过电位 .考察了温度、阳极电流密度、Nd2 O3添加量、电解质组成等因素对阳极过电位的影响 ,探讨了降低阳极过电位的可能途径 .结果表明 ,阳极过电位随阳极电流密度的增加而增大 ,随温度的升高而减小 ,一定范围内 ,阳极过电位与阳极电流密度的对数呈线性关系 ,满足塔菲尔方程 ;电解质中LiF和Nd2 O3浓度增加 ,阳极过电位降低 ;适当控制阳极电流密度、升高温度、增加电解质中LiF和Nd2 O3的浓度并尽可能减小极间距 ,均有利于降低阳极过电位     

溶胶-凝胶生物玻璃多孔材料显微结构和生物活性的扫描电镜及红外光谱分析

本文利用溶胶．凝胶法制备了CaO-P2O5-SiO，系统生物活性玻璃，并以其为原料制备了用于骨修复及骨组织工程支架的块状生物活性材料。利用体外实验方法(invitro)结合x射线衍射(XRD)、扫描电子显微镜(SEM)和傅立叶变换红外光谱分析(FTIR)技术对不同烧结工艺制备的材料结构、晶相和生物活性的影响进行了分析研究。研究表明，经800℃和1100℃烧结5min的两种材料均有硅磷酸钙Ca5(PO4)2SjO4微晶相析出。烧结温度越高，析出微晶相的体积比例越大，材料的生物活性则越低。在模拟生理溶液中碳酸羟基磷灰石(HCA)只在烧结体中的玻璃颗粒表面形成，而在其硅磷酸钙Ca5(PO4)2SiO4微晶相表面未发现HCA形成。     

苯乙烯与1-(2-叔丁基过氧异丙基)-3-异丙烯基苯共聚行为研究

苯乙烯与1－（2－叔丁基过氧异丙基）－3－异丙烯基苯（D120）能进行自由基共聚合反应，聚合后过氧基团以侧基的形成被保留在共聚物大分子链上，凝胶色谱分析发现，随原料单体中D120比例增加，共聚物的分子量减小，分子量分布变窄，DSC分析发现共聚物中过氧基团的分解温度随D120结构单元含量的增加而下降，但仍高于D120单体过氧基团的分解温度，苯乙烯与D120的竞聚率为：rD120=0.700,rSt=0.714。     

Complex amplitude estimation in the known steering matrix and generalized waveform case

We consider a special growth-curve (SGC) model with a known steering matrix and generalized waveform in the presence of unknown interference and noise. Several estimators of the complex amplitude based on this model are derived, including the methods of approximate maximum likelihood (AML), minimum variance distortionless response (MVDR), and amplitude and phase estimation (APES). We analyze the statistical properties of these estimators and show that in the presence of temporally white but spatially correlated noise and interference, AML is asymptotically statistically efficient for a large snapshot number while MVDR and APES are asymptotically equivalent but not statistically efficient. Via several numerical examples, we also show that when the noise and interference are both spatially and temporally correlated, the APES estimator can achieve better estimation accuracy and exhibit greater robustness than the other methods.     

Design of photonic crystal fibers for dispersion-related applications

A general procedure for design of photonic crystal fibers (PCFs) with desirable dispersion properties is presented. The design model is based on the combination of a rigorous vector mode solver and a scaling transformation for the dispersion properties of the PCFs. In comparison with the conventional design method, the new design procedure is more efficient and can be readily automated for the purpose of design optimization. Several applications of the design procedure, e.g., the design optimization for dispersion shifted fibers, dispersion flattened fibers, and dispersion compensation fibers, are demonstrated and discussed.     

Orthogonal space-time block codes: maximum likelihood detection for unknown channels and unstructured interferences

Space-time coding (STC) schemes for communication systems employing multiple transmit and receive antennas have been attracting increased attention. The so-called orthogonal space-time block codes (OSTBCs) have been of particular interest due to their good performance and low decoding complexity. In this paper, we take a systematic maximum-likelihood (ML) approach to the decoding of OSTBC for unknown propagation channels and unknown noise and interference conditions. We derive a low-complexity ML decoding algorithm based on cyclic minimization and assisted by a minimum amount of training data. Furthermore, we discuss the design of optimal training sequences and optimal information transfer to an outer decoder. Numerical examples demonstrate the performance of our algorithm.     

Microstructure and properties of MoSi2–MoB and MoSi2–Mo5Si3 molybdenum silicides

MoSi₂-based intermetallics containing different volume fractions of MoB or Mo₅Si₃ were fabricated by hot-pressing MoSi₂, MoB, and Mo₅Si₃ powders in vacuum. Both classes of alloys contained approximately 5 vol.% of dispersed silica phase. Additions of MoB or Mo₅Si₃ caused the average grain size to decrease. The decrease in the grain size was typically accompanied by an increase in flexure strength, a decrease in the room temperature fracture toughness, and a decrease in the hot strength (compressive creep strength) measured around 1200 °C, except when the Mo₅Si₃ effectively became the major phase. Oxidation measurements on the two classes of alloys were carried out in air. Both classes of alloys were protected from oxidation by an in-situ adherent scale that formed on exposure to high temperature. The scale, although not analyzed in detail, is commonly recognized in MoSi₂ containing materials as consisting mostly of SiO₂. The MoB containing materials showed an increase in the scale thickness and the cyclic oxidation rate at 1400 °C when compared with pure MoSi₂. However, in contrast with the pure MoSi₂ material, oxidation at 1400 °C began with a weight loss followed by a weight gain and the formation of the protective silica layer. The Mo₅Si₃ containing materials experienced substantial initial weight losses followed by regions of small weight changes. Overall, the MoB and Mo₅Si₃ additions to MoSi₂ tended to be detrimental for the mechanical and oxidative properties.     

山西铝厂锅炉水冷壁膨胀异常原因分析及对策

针对山西铝厂160t／h锅炉在实际运行中膨胀异常的问题，对不同的施工方法下，水冷壁膨胀量是否正常这一问题进行分析，找出了水冷壁膨胀异常的原因，并提出了解决对策。