语音时域分割研究

在语音时域挑选剩余可懂度低的可用置换集合,置换集合是语音TDS系统中不可缺少的重要环节,本文给出了可用置换选取的条件、客观评价标准和方法。     

The effects of plasma etching induced gate oxide degradation onMOSFET's 1/f noise

The effects of the plasma etching process induced gate oxide damages on device's low frequency noise behavior are investigated on MOSFET's fabricated with different field plate perimeter to gate area ratio antennas. Abnormal 1/f noise spectrum with a shoulder centered in the frequency range of 100 and to 1 kHz was frequently observed in small geometry devices, and it is attributable to a nonuniform distribution of oxide traps induced by plasma etching process     

用单片机控制的安全报警器的设计

文中简要地介绍了一个具有分散采集信号，集中报警的安全报警器的设计，作者利用单片机的优点和功能，成功地设计了复盖地域大，既简单又灵活的报警器。     

Transient behavior of subthreshold characteristics of fullydepleted SOI MOSFETs

It has been found that the subthreshold currents of fully depleted silicon-on-insulator (SOI) MOSFETs show a transient behavior under certain front-gate and back-gate voltage conditions. The cause of this anomaly is explained, and applications for the phenomenon are pointed out. Particularly, a simple way to measure the silicon film thickness is suggested     

All-optical photonic switches using integrated inverted asymmetricFabry-Perot modulators and heterojunction phototransistors

InGaAs/GaAs(100) multiple-quantum-well-based inverted cavity asymmetric Fabry-Perot modulators are vertically integrated with GaAs/AlGaAs heterojunction phototransistors to yield all-optical photonic switches. The photonic switches using `normally on' modulator pixels exhibit an output on-off ratio of 12:1 with internal optical gain of 4 dB. The photonic switches using `normally off' modulator pixels yield similar contrast and gain, but exhibit intrinsic bistable behavior. The inverted cavity modulators employed permit utilizing the transparency of the GaAs substrate at the operating wavelength and offer advantages for fabricating large arrays for optical signal processing     

Electrical characterization of porous BaTiO3 using impedance spectroscopy in humid condition

The humidity response characteristics of La doped BaTiO₃ with different sintered densities and room temperature electrical conductivities were investigated using complex impedance measurement. The samples with low density and high resistivity showed the large and nearly linear sensitivity to the change of humidity. The impedance spectra of samples, when exposed to high humidity, can exhibit microstructure-related features, even though they do not give rise to a noticeable characteristic change when exposed to low humidity. The observed impedance patterns were dependent upon the density, and hence the oxidation kinetics of BaTiO₃.     

Analysis and observation of backscatter-induced crosstalk in a 2-DFDM fiber gyro system

The modulation characteristics of first-order backscatter-induced crosstalk noise in a 2-D frequency-division-multiplexed fiber gyro system are analyzed and experimental results presented. The noise can be reduced from 5°/h to 0.2°/h (0.25 NEB) by proper choice of modulation depth and/or frequency     

The use of doped polyaniline as an electrode in the galvanic anodic protection of ferrous metals in industrial acid solutions

In order to investigate the galvanic anodic protection (GAP) of ferrous metals (such as 410, 304 and 316 stainless steels) in acid solutions by doped polyaniline (PANi), separate doped PANi powder-pressed electrodes with different surface areas (the area ratio of the PANi electrode to stainless steel is between 1:1 and 1:2) have been prepared. These were coupled with ferrous metal in the following solutions: 5 M sulphuric acid, 5 M phosphoric acid and industrial phosphoric acid (containing 5 M phosphoric acid and 0.05% chloride ion) to construct a galvanic cell, in which PANi is cathode while ferrous metal is anode. The results indicate that a PANi electrode with sufficient area can provide corrosion protection to stainless steel in these acidic solutions. A pilot scale coupling experiment was carried out. The results indicate that PANi is a promising material as an electrode for the anodic protection of ferrous metals in acidic solutions in industrial situations.     

A knowledge-based system for sensor selection

This paper presents a Knowledge-based system (KBS) developed to allow users, who may not be knowledgeable about sensors, to select sensors suitable for their specific needs. The KBS runs on a micro-computer. The selection criteria are user specified and are based on the desired measurement parameters. The system output includes all of the operational and dimensional parameters of the recommended sensor, price, and vendor information.