Modelling biological processes under anaerobic conditions through integrating titrimetric and off-gas measurements-applied to EBPR systems.

An innovative method for modelling biological processes under anaerobic conditions is presented and discussed. The method is based on titrimetric and off-gas measurements. Titrimetric data is recorded as the addition rate of hydroxyl ions or protons that is required to maintain pH in a bioreactor at a constant level. An off-gas analysis arrangement measures, among other things, the transfer rate of carbon dioxide. The integration of these signals results in a continuous signal which is solely related to the biological reactions. When coupled with a mathematical model of the biological reactions, the signal allows a detailed characterisation of these reactions, which would otherwise be difficult to achieve. Two applications of the method to the enhanced biological phosphorus removal processes are presented and discussed to demonstrate the principle and effectiveness of the method.     

CMOS gyrator-C active transformers

A systematic approach for synthesising gyrator-C active transformers using MOS transistors is presented. The topology of gyrator-C active inductors and their characteristics are briefly reviewed first. This is followed by the development of ideal gyrator-C active transformers, where only the capacitor loads of the transconductors synthesising active transformers are considered. The self and mutual inductances of both the primary and secondary windings of active transformers are investigated in detailed. Non-ideal gyrator-C active transformers are developed with the consideration of both the resistance and capacitance loads of transconductors. The intrinsic relation between the self and mutual inductances is derived. The configuration of gyrator-C active transformers with multiple primary and secondary windings is also developed. The proposed active transformers offer large and tunable self and mutual inductances with virtually no silicon area requirement. Several practical implementations of the proposed active transformers have been realised in TSMC-0.18 mum 1.8 V CMOS technology and analysed using SpectreRF with BSIM3v3 device models. Simulation results on voltage transfer characteristics, self and mutual inductances, quality factors, stability, the effect of process variations, and noise are presented. The application of the proposed active transformers is exemplified using a 1.6 GHz active transformer quadrature oscillator.     

Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

Tensile and flexural creep rupture tests on partially-damaged concrete specimens

Three series of novel tensile and flexural creep tests on partially-damaged concrete specimens were carried out in order to gain some insight into creep crack growth and failure of strain-softening materials. In the tests, each specimen was initially loaded to a given point in the descending branch and thus had a lower load-carrying capacity than that at the peak-point. Then, the specimen was unloaded and reloaded to sustain a load which was from 70% to 95% of its current load-carrying capacity. Experimental creep curves display a three-stage process, consisting of primary, secondary and tertiary stages, with a decreasing, constant and increasing creep rate, respectively. The secondary stage dominates the whole failure lifetime, whereas both the secondary and tertiary stages are important in terms of creep deformation. Failure life-time seems to be more sensitive to the change of load level in flexural tests rather than in tensile tests. The decrease in load-carrying capacity due to damage tends to result in a shorter failure lifetime and a lower critical load level for creep rupture. The descending branch of the static load-deflection or load-CMOD curve may be used as an envelope criterion for creep fracture.     

The changes of lipid metabolism and hemorrheology in intrahepatic cholestasis during pregnancy

OBJECTIVE: To identify the influence of the increased level of serum cholyglycine (CG) on lipid metabolism and hemorrheology in patients with intrahepatic cholestasis during pregnancy (ICP). METHODS: The concentrations of serum CG, total cholesterol (CH), triglycerides (TG), high density lipoprotein-cholesterol (HDL-C), low density lipoprotein-cholesterol (LDL-C), high shear and low shear of blood specific viscosity (HS and LS), plasma specific viscosity (PV) and hematocrit (HCT) were measured in 68 cases of primiparas with single pregnancy and 30 healthy nonpregnant women respectively. The group of ICP was composed of 35 cases with CG > 6 mumol/L, the group of normal pregnancy, 33 cases with CG < 6 mumol/L. RESULTS: The means of CG and the lipidic parameters in the two pregnant groups were significantly higher than those in the non-pregnancy group (P < 0.02-0.001) except the means of HDL-C between the groups of ICP and non-pregnancy. The levels of LDL-C, LDL-C/HDL-C, LS, PV and HCT in the ICP were significantly higher than those in the normal pregnancy group (P < 0.02-0.001). CONCLUSIONS: There are significant changes of lipid metabolism and hemorrheology in patients with ICP. However, these changes could be corrected after pregnancy termination, when the level of serum CG returned to normal. The results suggest that the pathophysiologic changes of ICP are associated with increased level of serum CG.     

Finite-difference time-domain analysis and experimental examinationof the performance of a coupled-cavity MQW laser/active waveguide at1.54 μm

The performance characteristics of a coupled cavity InGaAsP-InP MQW laser/active waveguide made by one-step epitaxy and well-controlled reactive ion etching (RIE) have been theoretically analyzed and experimentally determined. A theoretical model based on a finite-difference time-domain (FDTD) technique was used to simulate the propagation of an optical wave launched in the coupled system and determine the reflectivity of the facets created by RIE. The calculated effective reflectivity of the coupling region consisting of two facets and an air gap is between 0.45 and 0.55, which is in good agreement with the experimentally measured value of 0.5. The reflectivity of a single etched mirror derived from this value is estimated to be 0.3. A 120-μm-long monolithically integrated active waveguide when biased as a modulator and excited by the laser shows a maximum extinction ratio of 8 dB and a modulation bandwidth ⩾14 GHz at a dc bias of -0.5 V with a bias swing of 2 V     

烧成及热处理工艺对钛酸锶铅基热敏材料性能及显微结构的影响

研究了烧成及热处理工艺对钛酸锶铅基热敏材料的阻温特性及显微结构的影响。通过扫描电镜（ＳＥＭ）和能量分散仪（ＥＤＡＸ）分析了材料的显微结构及不同形貌晶粒的成份。通过对组成、烧成及热处理工艺的控制，可得到具有Ｖ型ＰＴＣＲ特性的热敏材料。     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

新型复合弹簧的研究

提出一种金属圆锥弹簧与橡胶圆锥弹簧复合而成的弹簧．分析表明：它可以应用于弹性耦合激励振动筛和座式直线振动筛。