Solution of Helmholtz equation by Trefftz method

The application of the Trefftz method for calculating wave forces on offshore structures is presented. Indirect and direct formulations using complete and non-singular systems of Trefftz functions for the Helmholtz equation are posed in this paper. An effective technique using different interpolation functions for the velocity potential and wave force are suggested to improve the computational accuracy of the wave force. The numerical examples show that the present method is highly efficient and accurate.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

氩等离子体辐照反相乳液接枝改性涤纶织物的研究

首次提出了在等离子体辐照后再用反相乳液接枝改性涤纶织物的新方法,探讨了接枝颗粒特征以及织物各项物理力学性能.接枝织物的结构及性能的测试结果表明:接枝物的尺寸远小于纤维的直径,在提高织物吸湿性的同时,对织物透气性能和强力等无明显影响;实验也证实了乳液中未接枝单体可以再次聚合.     

两种塑料纸芯管结构与性能比较分析

测试与分析了两种塑料管材的拉伸与弯曲性能、热变形温度、结晶性和化学组成,分析结果表明:管材B较管材A具有更高模量与热变形温度,但管材B较高的分子量与较小的分子量分布抑制管材产品内在的均匀性,且管材B中的α晶在高温下向β晶的转变可能会影响管材长期使用性能.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Polyetherimide substrates for future high density optical data storage

Polyetherimide (PEI) substrate for next‐generation high density optical data storage is fabricated and characterized. Cover‐layer incident or first‐surface recording configurations do not require optical properties of the substrate, which are the prerequisite conditions for the conventional material of polycarbonate (PC). Instead of the optical properties, good mechanical properties with a sufficient transcribability are required. Even though PEI has higher glass transition temperature than that of PC, a microscopic transcribability of PEI is comparable with PC by laminating a thermal insulation layer on the backside of a stamper to retard the heat flow. A macroscopic warpage of PEI substrate is smaller than that of PC substrates, which reduces tilt and servo burden. The lowest critical speed coupled with the flutter of PEI substrate is larger than that of PC substrate because of the mechanical properties of PEI. POLYM. ENG. SCI., 48:97–101, 2008. © 2007 Society of Plastics Engineers