尿素醇解合成碳酸酯类化合物技术进展

综述了用尿素醇解合成碳酸酯类化合物的技术进展 ,重点介绍尿素醇解合成碳酸二甲酯研究现状以及与其它工艺路线的比较 ,另外也介绍了尿素醇解合成长碳链脂肪族和芳香族类碳酸酯的研究进展。     

单刻线样板检定装置测量不确定度分析

分析了单刻线样板检定装置的测量不确定度，并分析了用该检定装置检定的单刻线样板的不确定度。     

基于ISP技术的自动测试系统信号处理研究

在VXI总线模块及GPIB仪器构成的自动测试系统中 ,利用ispLSI10 3 2实现了测试信号的动态分配和预处理 ,有效解决了测试平台对多种复杂被测对象的适配问题。     

液态混合有机标准物质研究

本研究采用重量法配制有机液态混合标样 ,并对配制方法、混合标样的均匀性、稳定性及影响不确定度的因素进行了研究 ,并用气相色谱法进行了比对分析。经稳定性监测 ,稳定度大于等于一年 ,不确定度小于± 2 %。     

基于泛布尔代数的结构振动控制机理

本文介绍了泛布尔代数的数学模型、公理体系和化简方法 ;针对高层建筑的特点 ,舍弃寻求被控制对象的精确数学模型 ,提出了“基于泛布尔代数的结构振动控制” ,分析了其的逻辑机理 ,建立了基于泛布尔代数的MR阻尼器的半主动控制算法。应用本文提出的控制方针对 12层的高层结构受控地震反应的模拟仿真 ,结果表明其控制简单、灵活、方便 ,能满足这种结构的控制要求。     

Preliminary<Emphasis Type="Italic">in vitro</Emphasis> and<Emphasis Type="Italic">in vivo</Emphasis> characterizations of a sol-gel derived bioactive glass-ceramic system

This study investigates quantitatively and qualitatively the sol-gel derived bioactive glass-ceramic system (BGS)—apatite-wollastonite (AW) type granules in the size range of 0.5–1 mm, as an effective graft material for bone augmentation and restoration. Scanning electron micrographs (SEM) of the sintered granules revealed the rough material surface with micropores in the range 10–30 μm. X-ray diffraction (XRD) pattern of the granules revealed the presence of crystalline phases of the hydroxyapatite and wollastonite, and the functional groups of the silicate and phosphates were identified by Fourier transform infrared spectroscopy (FT-IR). Thein vitro cell culture studies with L929 mouse fibroblast cell line showed very few cells adhered on the BGS disc after 24 h. This could be due to the highly reactive surface of the disc concomitant with the crystallization but not due to the cytotoxicity of the material, since the cellular viability (MTT assay) with the material was 80‰ Cytotoxicity and cytocompatibility studies proved that the material was non-toxic and biocompatible. After 12 weeks of implantation of the BGS granules in the tibia bone of New Zealand white rabbits, the granules were found to be well osteointegrated, as observed in the radiographs. Angiogram with barium sulphate and Indian ink after 12 weeks showed the presence of microcapillaries in the vicinity of the implant site implicating high vascularity. Gross observation of the implant site did not show any inflammation or necrosis. SEM of the implanted site after 24 weeks revealed good osteointegration of the material with the newly formed bone and host bone. New bone was also observed within the material, which was degrading. Histological evaluation of the bone healing with the BGS granules in the tibial defect at all time intervals was without inflammation or fibrous tissue encapsulation. After 2 weeks the new bone was observed as a trabeculae network around the granules, and by 6 weeks the defect was completely closed with immature woven bone. By 12 weeks mature woven bone was observed, and new immature woven bone was seen within the cracks of the granules. After 24 weeks the defect was completely healed with lamellar bone and the size of the granules decreased. Histomorphometrically the area percentage of new bone formed was 67.77% after 12 weeks and 63.37% after 24 weeks. Less bone formation after 24 weeks was due to an increased implant surface area contributed by the material degradation and active bone remodeling. The osteostimulative and osteoconductive potential of the BGS granules was established by tetracycline labelling of the mineralizing areas by 2 and 6 weeks. This sol-gel derived BGS granules proved to be bioactive and resorbable which in turn encouraged active bone formation.     

Isothermal Gas Forming of Mg Alloy AZ31 Sheet

There have been reports on sheet forming of Mg alloy in industry via the punch and die method;this paper is probably the first formal one for studying the sheet formability of AZ31 employing pressurized gas to press the sheet into a female die cavity at various elevated temperatures.The results indicate it is feasible to form a rectangular box via pressurized gas from extruded sheets of 0.5 and 1.7 mm thick.The formed box has 1:2 depth over width ratio,which should be large enough when dealing with realistic industrial sheet forming parts.Presently,forming a sheet of 0.5 mm thick is considered a technical challenge by industry,and it is conquered as demonstrated in this paper.Gas forming technique applied to Mg alloy is unprecedented and shows potential for industrial utilization.     

关于最远点判定及直径的唯一性

给出了点到有界集最远点的一些必要或充分条件，然后对直径的唯一性也给出了一些判定条件。     

硅粉/酚醛制备低成本碳化硅陶瓷复合材料

以低成本的硅粉和酚醛为原料 ,采用浆料浸渍 热压成型 反应烧结法制备了Cf SiC单向板 ,并对工艺条件进行了探讨。制备得到的单向板的弯曲强度达到 45 6 .8MPa ,断裂韧性达到 7.94MPa·m1 2 。