Broad-band erbium-doped fiber amplifier with double-passconfiguration

We demonstrate a broad-band silica-based erbium-doped fiber amplifier (EDFA) with double-pass configuration. The signal gain and noise figure are obtained more than 24 dB and less than 6 dB, respectively, for 1526-1562 nm and 1569-1605 nm. The same signal gain can be achieved with 53% less pump power and 45% shorter erbium-doped fiber length, compared to a conventional parallel type EDFA. Furthermore, the noise figure and power conversion efficiency are improved for the wavelength range     

Design and Architecture of Low‐Latency High‐Speed Turbo Decoders

In this paper, we propose and present implementation results of a high‐speed turbo decoding algorithm. The latency caused by (de)interleaving and iterative decoding in a conventional maximum a posteriori turbo decoder can be dramatically reduced with the proposed design. The source of the latency reduction is from the combination of the radix‐4, center to top, parallel decoding, and early‐stop algorithms. This reduced latency enables the use of the turbo decoder as a forward error correction scheme in real‐time wireless communication services. The proposed scheme results in a slight degradation in bit error rate performance for large block sizes because the effective interleaver size in a radix‐4 implementation is reduced to half, relative to the conventional method. To prove the latency reduction, we implemented the proposed scheme on a field‐programmable gate array and compared its decoding speed with that of a conventional decoder. The results show an improvement of at least five fold for a single iteration of turbo decoding.     

Preparation and Characterization of Bi2Te3/Sb2Te3 Thermoelectric Thin-Film Devices for Power Generation

A device based on a new double-layer-leg thin-film concept has been successfully fabricated by flip-chip bonding of 242 pairs of n-type Bi₂Te₃ and p-type Sb₂Te₃ thin-film legs electrodeposited on top substrates to those processed on bottom substrates. Based on the output voltage–current curve, the internal resistance of the double-layer-leg thin-film device was measured to be 3.47 kΩ at an apparent temperature difference of 25.9 K across the device. The actual temperature difference across the thin-film legs was estimated to be 3.51 K, which is ～13% of the apparent temperature difference ΔT of 25.9 K applied across the thin-film device. The double-layer-leg thin-film device exhibited an open-circuit voltage of 0.43 V and maximum output power of 13.1 μW at an apparent temperature difference ΔT of 25.9 K.     

Reply to comments on 'Efficient realisation of alternating projection algorithm for maximum likelihood direction finding'

For the original article see ibid., vol.25, no.20, p.1325-6 (1989) and for comments on the article see ibid., vol.27, no.20, p.1848 (1991). The authors reply to the comments by Zhang and Zhu, pointing out that the commenters have misunderstood the authors' approach. Hence an explanation of their approach is given.<>     

Virus‐Templated Self‐Mineralization of Ligand‐Free Colloidal Palladium Nanostructures for High Surface Activity and Stability

In solution‐based synthesis of colloidal nanostructures, additions of ligands, stabilizers, and redox reagents are generally required to obtain desirable structures, though ligands and stabilizers on the surface of nanostructures can substantially affect the surface‐related activity. Accordingly, an extensive rinsing process is usually required to remove residual reagents and stabilizers. This study reports a spontaneous self‐biomineralization of palladium (Pd) ions on a filamentous virus to form ligand‐free Pd nanowires under ambient conditions. No reducing reagents or additional surface stabilizers are used; the genetically modified virus alone supports the polycrystalline Pd nanowires within the nanostructure, maintaining the clean surface even without a rinsing process. The advantage of the ligand‐free Pd nanowires is found in the Suzuki‐coupling reaction, in which the nanowire catalytic activity is maintained after repeated reactions, while conventional Pd colloids undergo surface contamination by the stabilizer and lose their catalytic activity during repeated uses. The ligand‐free surface, high electronic connectivity, and structural stability of the Pd nanowires also allow high sensitivity and selectivity in hydrogen gas sensing analysis. This work emphasizes the importance of the ligand‐free surface of biotemplated nanostructures in maintaining functionalities without surface contamination.     

Low Complexity Decoder Architecture for Low-Density Parity-Check Codes

In this paper, we propose a low complexity decoder architecture for low-density parity-check (LDPC) codes using a variable quantization scheme as well as an efficient highly-parallel decoding scheme. In the sum-product algorithm for decoding LDPC codes, the finite precision implementations have an important tradeoff between decoding performance and hardware complexity caused by two dominant area-consuming factors: one is the memory for updated messages storage and the other is the look-up table (LUT) for implementation of the nonlinear function Ψ(x). The proposed variable quantization schemes offer a large reduction in the hardware complexities for LUT and memory. Also, an efficient highly-parallel decoder architecture for quasi-cyclic (QC) LDPC codes can be implemented with the reduced hardware complexity by using the partially block overlapped decoding scheme and the minimized power consumption by reducing the total number of memory accesses for updated messages. For (3, 6) QC LDPC codes, our proposed schemes in implementing the highly-parallel decoder architecture offer a great reduction of implementation area by 33% for memory area and approximately by 28% for the check node unit and variable node unit computation units without significant performance degradation. Also, the memory accesses are reduced by 20%.     

Writing current reduction and total set resistance analysis in PRAM

We evaluated the limit of scaling bottom electrode contact (BEC) heater size and high resistivity heater to reduce writing current. It was found that the resistivity of heater should be increased for reducing writing current below the heater size of about 50 nm without any undesirable increase of resistance of the crystalline state (SET state, Rset). It was shown in the numerical simulations that the dissipated heat loss through BEC during melting GST was decreased in the increase of resistivity of heater. In addition, we analyzed the resistance components contributing to the total set resistance. It was observed that the undesired sharp increase of Rset as the BEC size decreases below 50 nm was attributed to the resistance component of GST–BEC interface. In the case of high resistivity heater, the contributions of both incomplete crystallization and heater itself were enhanced.     

QoS‐aware routing and power control algorithm for multimedia service over multi‐hop mobile ad hoc network

This paper presents a QoS (quality of service) aware routing and power control algorithm consuming low transmission power for multimedia service over mobile ad hoc network. Generally, multimedia services need stringent QoS over the network. However, it is not easy to guarantee the QoS over mobile ad hoc network since its network resources are very limited and time‐varying. Furthermore, only a limited amount of power is available at mobile nodes, which makes the problem more challenging. We propose an effective routing and power control algorithm for multimedia services that satisfies end‐to‐end delay constraint with low transmission power consumption. The proposed algorithm supports the required bandwidth by controlling each link channel quality over route in a tolerable range. In addition, a simple but effective route maintenance mechanism is implemented to avoid link failures that may significantly degrade streaming video quality. Finally, performance comparison with existing algorithms is presented in respect to traditional routing performance metrics, and an achievable video quality comparison is provided to demonstrate the superiority of the proposed algorithm for multimedia services over mobile ad hoc network. Copyright © 2010 John Wiley & Sons, Ltd.