Performance of fluorine-added CoMoS/Al2O3 prepared by sonochemical and chemical vapor deposition methods in the hydrodesulfurization of dibenzothiophene and 4,6-dimethyldibenzothiophene

The performance of a new type of CoMoS/Al₂O₃ catalyst, with added fluorine and prepared by sonochemical and chemical vapor deposition (CVD) methods, was investigated in the hydrodesulfurization (HDS) of dibenzothiophene (DBT) and 4,6-dimethyldibenzothiophene (4,6-DMDBT). The catalyst, which was designed to contain optimum amounts of fluorine and cobalt, exhibited a higher activity, ca. 4.6 times higher activity particularly in the HDS of 4,6-DMDBT, than a fluorine-free catalyst prepared by a conventional impregnation method. The enhanced activity of the new catalyst can be attributed to the cumulative effects of individual factors involved in the catalyst preparation. That is, the use of a sonochemical synthesis led to a high dispersion of small MoS₂ crystallites on the alumina, and the addition of the Co species to the catalyst by CVD caused a close interaction between the Co species and the MoS₂ crystallites to produce numerous CoMoS species, which are the catalytically active species for HDS. The addition of fluorine increased the amounts of acidic sites in the catalyst, which promoted hydrogenation (HYD) route to a greater extent than the direct desulfurization (DDS) route in DBT HDS and both HYD and DDS routes to similar extents in the case of 4,6-DMDBT HDS. Accordingly, the addition of fluorine led to a greater increase in catalytic activity for 4,6-DMDBT HDS than for DBT HDS.     

Low‐temperature photoinitiation solution polymerization behavior of N‐vinylcarbazole in tetrahydrofuran

N‐Vinylcarbazole (VCZ) was solution‐polymerized in tetrahydrofuran (THF) at ?20, 0, and 20°C using the photoinitiation method; the effects of the amount of solvent, polymerization temperature, and photoinitiator concentration were investigated. On the whole, the experimental results corresponded to predicted ones. Low polymerization temperature using photoinitiation proved to be successful in obtaining poly(N‐vinylcarbazole) (PVCZ) of a high molecular weight with a smaller temperature rise during polymerization; nevertheless of free radical polymerization by 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN). The photo‐solution polymerization rate of VCZ in THF was proportional to the 0.47 power of ADMVN concentration. The molecular weight was higher and the molecular weight distribution was narrower with PVCZ polymerized at lower temperatures. For PVCZ prepared in THF at ?20°C using a photoinitiator concentration of 0.00005 mol/mol of VCZ, a weight‐average molecular weight of 510,000 was obtained, with a polydispersity index of 1.73, and a degree of lightness converged to about 99%. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3667–3672, 2002     

Electrosteric stabilization of concentrated cement suspensions imparted by a strong anionic polyelectrolyte and a non-ionic polymer

Strong polyelectrolytes, known as superplasticizers, improve the initial fluidity of concentrated cement suspensions through electrostatic stabilization. These polyelectrolytes do not maintain the initial fluidity, however, primarily due to an increase in the ionic strength of the cementitious suspension. Consequently, non-ionic polymers are often used in conjunction with polyelectrolytes to provide steric stabilization and hence to sustain the desired fluidity over a longer time, and this has lead to the development of copolymers with both electrostatic and steric (electrosteric) functionalities. To design such polymers, it is necessary to optimize the balance between electrostatic and steric stabilization to maximize suspension fluidity. We have quantified the effects of a strong anionic polyelectrolyte, melamine formaldehyde sulfonate (MFS), and a non-ionic polymer, hydroxypropylmethylcellulose (HPMC), on the zeta potential of cement particles and the steady shear and low-amplitude rheological properties of concentrated cement suspensions. While the adsorption of MFS onto the cement particle surfaces leads to a sign inversion in the zeta potential, the adsorption of the non-ionic HPMC has no significant effect on the potential. The addition of HPMC to the suspensions substantially reduces the steady shear viscosity and the storage modulus at constant MFS concentration; in addition, there exists an intermediate HPMC concentration that minimizes fluidity. The resulting suspension fluidity is also maintained over a longer time than in the absence of HPMC. This improvement in the stability and fluidity of cement suspensions is attributed to “complementary electrosteric dispersion/stabilization”, and provides insight to the design of polymers with electrosteric functionality.     

The temporal evolution of thermal instability in fluid layers isothermally heated from below

The temporal development of thermal disturbances in the fluid layer heated isothermally from below is investigated, based on propagation theory. This theory is examined by using scaling. To examine the behavior of thermal instability the mean-field approximation is employed and resulting equations are solved by Galerkin method. The stability criteria to mark the onset of convective instability are newly suggested as the intersection point of the growth rate of averaged temperature with that of its fluctuation. The resulting critical time is close to that derived from propagation theory. By considering the nonlinear effects, the characteristic times to represent the detection time of manifest convection and also to exhibit the minimum Nusselt number are discussed.     

Monooxygenase system of <Emphasis Type="Italic">Bacillus megaterium</Emphasis> ALA2: Studies on palmitic acid oxidation products

We identified many novel oxygenated FA produced from linoleic acid by microbial strain ALA2: 12,13,17-trihydroxy-9(Z)-octadecenoic acid (12,13,17-THOA); 12,13,16-trihydroxy-9(Z)-octadecenoic acid (12,13,16-THOA); 12-hydroxy-13,16-epoxy-9(Z)-octadecenoic acid; and 12,17;13,17-diepoxy-16-hydroxy-9(Z)-octadecenoic acid. 12,13,17-THOA, the main product, inhibits the growth of some plant pathogenic fungi. Recently, we reclassified strain ALA2 as Bacillus megaterium ALA2 NRRL B-21660 and opened a possible link with the well-studied catalytically self-sufficient P450 monooxygenase of Bacillus megaterium ATCC 14581 (NRRL B-3712) and B. subtilis strain 168 (NRRL B-4219). Now we have found that strain ALA2 also oxidizes palmitic acid into three oxygenated products: 13-, 14-, and 15-hydroxy palmitic acids. This indicates that strain ALA2 also possesses a monooxygenase system similar to the abovementioned well-known strains. These data facilitate studies on the oxygenase system of strain ALA2.     

Electrochemical cell current requirements for toxic organic waste destruction in Ce(IV)-mediated electrochemical oxidation process

The electrochemical cell for cerium oxidation and reactor for organic destruction are the most important operation units for the successful working mediated electrochemical oxidation (MEO) process. In this study, electrochemical cells with DSA electrodes of two types, single stack and double stack connected in series, were used. The performances towards the electrochemical generation of Ce(IV) in nitric acid media at 80 °C were studied. The current-voltage curves and cerium electrolysis kinetics showed the dependence on number of cell stacks needed to be connected in series for the destruction of a given quantity of organic pollutant. The presence of an optimum region for Ce(III) oxidation with a contribution of oxygen evolution, especially at low Ce(III) concentration (high conversion ratios), was found. The cells were applied for the Ce(IV) regeneration during the organic destruction. The cell and reactor processes were fitted in a simple model proposed and used to calculate the current needed in terms of Ce(III) oxidation rate and the number of cell stacks required for maintaining Ce(IV)/Ce(III) ratio at the same level during the organic destruction. This consideration was based on the kinetic model previously developed by us for the organic destruction in the MEO process.     

Development of modified stokes expression to model the behavior of expanded beds containing polydisperse resins for protein adsorption

Expanded bed behavior was modeled by using the Richardson-Zaki correlation between the superficial velocity of the feed stream and the void fraction of the bed. A polydisperse material, Chelating excellose® (70-210 Μm in diameter, 1.21 g/cm³ in density), which has Ni²⁺ ions for the selective binding of histidine-tagged proteins, was used as the resin. A method to modify the Stokes expression to express the terminal settling velocity of the resins by introducing two empirical parameters, the effective diameter of the resins and an exponent for(ρ _p -ρ)/Μ term, was developed. Combined use of the Richardson-Zaki correlation and the modified Stokes expression was successful in modeling the bed expansion by incorporating physical properties of feed streams and the resins.     

Preparation and electrical properties of metal sulfides–amidoximated PAN composite film

To improve the electrical conductivity of polyacrylonitrile (PAN) film, metallic sulfides and PAN composite film were prepared by the chelating method. Dense PAN film and porous PAN film were prepared by dry process and wet process, respectively. These PAN films were treated to NH₂OH solution to introduce the amidoxime group coordinated with metallic ion. Cu⁺² and Cd⁺² ions were adsorbed to amidoximated PAN films, the sulfur ion was treated with metal-adsorbed PAN films, and thus CuS—and CdS–PAN composite films were prepared. The adsorptive capacity of amidoximated PAN film for the Cu⁺² ion was independent of the morphology of the PAN film, but the adsorptive capacity of the Cd⁺² ion on amidoximated PAN film was dependent on porosity of the polymer. Adsorptive capacity of amidoximated porous PAN film for Cd⁺² was improved about four times than that of amidoximated dense PAN film. The electrical conductivities of CuS–dense and porous PAN composite film were both 10^?1 S/cm in optimum condition, but because of the difference in adsorptive capacity, the electrical conductivities of CdS–dense and CdS–porous PAN composite films were 10^?9 S/cm and 10^?4 S/cm, respectively. Additionally, because CdS was known as a photoconductive material, the photoconductive properties of CdS–porous PAN composite film were investigated.     

Wetting properties of polystyrene ionomers treated with plasma source ion implantation

The wetting properties of polystyrene‐based ionomers treated with plasma source ion implantation (PSII) were investigated by the measurement of water contact angles. When sulfonated ionomers were aged for a few days, the hydrophobic recovery for the ionomers became much slower than that for the nonionic polymers. However, when the samples were aged over 20 days, the water contact angle of the ionomers converged with that of the nonionic polymer. Thus, it was concluded that the ionic interaction between the ionic groups and the presence of ionic groups together resulted in the slow hydrophobic recovery and that the aging effect was significant for the ionomers. For the methacrylate ionomer of low ion content, on the other hand, it was found that the PSII treatment produced only a small change in hydrophobic recovery behavior. Thus, it was suggested that the low ionic content coupled with the small size of the ionic unit might cause changes only of a very insignificant degree in hydrophobic recovery behavior. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2500–2504, 2002     

Pb-Diffusion Barrier Layers for PbTiO3 Thin Films Deposited on Si Substrates by Metal Organic Chemical Vapor Deposition

The interfaces between metal organic chemical vapor deposited PbTiO₃ thin films and various diffusion barrier layers deposited on Si substrates were investigated by transmission electron microscopy. Several diffusion barrier thin films such as polycrystalline TiO₂, amorphous TiO₂, ZrO₂, and TiN were deposited between the PbTiO₃ thin film and Si substrate, because the deposition of PbTiO₃ thin films on bare Si substrates produced Pb silicate layers at the interface irrespective of the deposition conditions. The TiO₂ films were converted to PbTiO₃ by their reaction with diffused Pb and O ions during PbTiO₃ deposition at a gubstrate temperature of 410°C. Further diffusion of Pb and O induces formation of a Pb silicate layer at the interface. ZrO₂ did not seem to react with Pb and O during PbTiO₃ deposition at the same temperature, but the Pb and O ions that diffused through the ZrO₂ layer formed a Pb silicate layer between the ZrO₂ and Si substrate. The TiN films did not seem to react with Pb and O ions during the deposition of PbTiO₃ at 410°C, but reacted with PbTiO₃ to form a lead-deficient pyrochlore during postdeposition rapid thermal annealing at 700°C. However, TiN could effectively block the diffusion of Pb and O ions into the Si substrate and the formation of Pb silicate at the interface.