Fluidized bed combustion of high ash anthracite: Analysis of combustion efficiency and particle size distribution

Fluidized bed combustion of high ash anthracite (HAA) was experimentally studied. The combustor consists of 0.25 m ID bed, and auxiliary equipments for coal feeding, ash removal, lemperature control, etc. Experimental results elucidate main cause of fuel loss to be elutriation of fines (i.e., flyash) containing unburned carbon. However, detailed balances of particle size distribution show majority of carbon in flyash comes from fines contained in the feed instead of attrition of coarse particles. The latter is the main source of flyash for conventional coal. The difference is due to much smaller attrition rate of HAA; feed HAA particles do not shrink much in size by combustion and attrition.     

Effect of Ba6Ti17O40/BaTiO3 Interface Structure on {111} Twin Formation and Abnormal Grain Growth in BaTiO3

A structural transition of Ba₆Ti₁₇O₄₀/BaTiO₃ interfaces from faceted to rough was induced by reducing oxygen partial pressure in the atmosphere. As the oxygen partial pressure decreased, the number densities of {111} twins and abnormal grain decreased. TEM observation showed that the twin formation was governed only by the faceting of the interface. Experimental evidence of {111} twin-assisted abnormal growth of faceted BaTiO₃ grains was also obtained.     

Code-to-code comparison study on rotor aeromechanics in descending flight

This paper conducts the aeromechanics study using the two different rotorcraft computational structural dynamics (CSD) codes, CAMRAD II and DYMORE II, for the rotor in low-speed descending flight. The three test cases of the HART (Higher-harmonic control aeroacoustic rotor test) I -baseline, minimum noise, and minimum vibration- are considered in this study of the blade-vortex interaction (BVI) airloads, rotor trim, blade elastic deformations, and blade structural loads. The two prediction results are compared to each other for a code-to-code comparison study as well as to the measured data. Although CAMRAD II and DYMORE II use different theories and models, most of the prediction results are similar to each other and compared fairly well with the wind tunnel test data. For all the three test cases, the two rotorcraft CSD analyses show good prediction on the fluctuations of the section normal force (M²C_n) due to BVI, but both over-predict the trimmed collective pitch angle. The blade elastic deformations, such as flap deflection and elastic torsion deformation at the tip, are reasonably predicted by both rotorcraft CSD analyses. But, the CAMRAD II result using the multiple-trailer wake model with consolidation is slightly better than the DYMORE II prediction with the single wake panel model particularly for the elastic torsion deformation in the baseline case. In addition, CAMRAD II and DYMORE II both correlate reasonably the blade structural loads, such as flap bending, lead-lag bending, and torsion moments, with the measured data; however, the CAMRAD II results are moderately better than the DYMORE II predictions.     

Ce3+/Tb3+-coactived NaMgBO3 phosphors toward versatile applications in white LED,FED, and optical anti-counterfeiting

Ce³⁺/Tb³⁺ co-doped NaMgBO₃ phosphors were successfully synthesized by solid-state method. Under 381 nm excitation, the cyan emission owing to the 5d → 4f of Ce³⁺ ions and green emissions arising from the ⁵D₄ → ⁷F_J (J = 6, 5, 4, and 3) transitions of Tb³⁺ ions were seen in all the phosphors. Through theoretical analysis, one knows that the energy transfer from Ce³⁺ to Tb³⁺ ions with high efficiency of 83.74% was contributed by dipole–dipole transition. Furthermore, the internal quantum efficiency of NaMgBO₃:0.01Ce³⁺,0.03Tb³⁺ phosphor was 54.28%. Compared with that of at 303 K, the emission intensity of the developed products at 423 K still kept 73%, revealing the splendid thermal stability of the studied phosphors. Through utilizing the resultant phosphors as cyan-green components, the fabricated white-LED device exhibited an excellent correlated color temperature of 2785 K, high color-rendering index of 85.73, suitable luminance efficiency of 25.00 lm/W, and appropriate color coordinate of (0.4279, 0.3617). Aside from the superior photoluminescence, the synthesized phosphors also exhibited excellent cathode-luminescence properties which were sensitive to the current and accelerating voltage. Furthermore, the NaMgBO₃:0.01Ce³⁺,0.03Tb³⁺ phosphors with multi-mode emissions were promising candidates for optical anti-counterfeiting. All the results indicated that the Ce³⁺/Tb³⁺ co-doped NaMgBO₃ phosphors were potential multi-platforms toward white-LED, field emission displays, and optical anti-counterfeiting applications.     

Nitrogen removal using recycled polystyrene bottles as biofilm media

The performance of an attached growth wastewater treatment process was investigated in an effort to improve nitrogen removal efficiency. Recycled Yakult (lactic acid fermentation drink) bottles made of polystyrene were used as a biofilm media. The use of Yakult bottles as a biofilm media has been attempted by numerous researchers in Japan for the removal of solids and organics. However, these studies focused only on the removal of solids and organics. This study extended their application to the removal of nitrogen for domestic sewage treatment. Yakult media was placed in a reactor with 70% apparent reactor volume in a conventional A/O process. The bottom of the Yakult media was removed, and randomly filled Yakult media were effectively able to reduce the flow in tanks, resulting in an increase in the contact time between pollutants and microorganisms. With higher HRT, the nitrogen removal efficiency was increased by up to 83% with 12 hr of HRT. Nitrification appeared to be the limiting factor of nitrogen removal at an HRT that is less than 12 hr, indicating that the Yakult process requires more retention time to achieve nitrification compared to other biofilm processes. The removal efficiencies of organics and solids were high regardless of the change of operational parameters. This article is based on a presentation in “The 7th Korea-China Workshop On Advanced Materials” organized by the Korea-China Advanced Materials Cooperation Center and the China-Korea Advanced Materials Cooperation Center, held at Ramada Plaza Jeju Hotel, Jeju Island, Korea on August 24–27, 2003.     

Effect of low-cycle fatigue on the hot ductility of plain carbon steel

In a continuous casting steelmaking operation, the surface of a slab is under a condition that can be characterized as high-temperature, low-cycle fatigue in which the tensile and compressive stress is repeatedly developed. For this reason, for the evaluation of the hot ductility of a slab, considering the fatigue deformation is more feasible before a tensile or compressive test. In this study, the effects of low-cycle fatigue on the hot ductility of steels with a carbon content of 0.06–0.8 wt.% are investigated at various temperatures. For a carbon content of 0.06%, there were no significant differences between the RA values from a simple tensile test and those from a tensile test after fatigue deformation. The tendency of ductility deterioration with fatigue deformation is evident in 0.1 %C steel, and is due to the deformation-induced ferrite film that forms around the prior austenite grain. Conversely, high carbon steel containing 0.8 %C did not show a recovery of hot ductility in a low temperature region, and the specimen on which the tensile was measured after fatigue showed a higher hot ductility in the low temperature region, which is thought to result from the pearlite refinement effects. As the results obtained in this work showed noticeable differences in the hot ductility of carbon steel through the test conditions, it is suggested that for more accurate data, fatigue deformation be adopted in which the temperature range in an unbending operation is determined in the steelmaking factory.     

Separation of oxide inclusions from liquid metal in an applied electrostatic field

It is known that oxide inclusions in liquid metal carry mostly positive charges on their surfaces. In an electrostatic field, therefore, such charged particles suspended in a liquid metal experience forces and accumulate in the region of the negatively charged surface, resulting in the separation of oxide inclusions from the liquid metal. In this study, this principle was experimentally demonstrated for the case of a capacitor cell by the imposition of a d.c. potential on electrodes. The capacitor cell consisted of a dielectric container of Pyrex tube, a high voltage d.c. source, and two electrodes, which were symmetrically attached onto the outer surface of the Pyrex. tube. Experiments were carried out for suspensions of liquid tin/metal oxides, such as SnO₂, WO₃, and PbO under an applied potential of up to 12 kV. All experimental results were in good agreement with the theoretical prediction and showed that the degree of separation was significantly increased with the applied potential.     

Thermodynamic reassessment of the Cd−Zn system

The Cd−Zn system has been thermodynamically reassessed with the CALPHAD method by combining more recent experimental data, in particular the activities of zinc in the liquid phase. A good agreement is obtained between the calculated and experimental thermodynamic parameters as well asphase boundaries.     

How purchase intention consummates purchase behaviour: the stochastic nature of product valuation in electronic commerce

This study challenges the conventional assumption that online customers with high purchase intention routinely move to the purchase stage. To this end, the process of how online customers form purchase intention and behaviour is examined. On the basis of product value distribution (PVD), we propose that the hypothetically expected product value (i.e. PVD average) determines purchase intention, whereas the actual probability of attaining the expected product value (i.e. PVD variance) moderates purchase behaviour. This proposal indicates that the expected product value has significance only when repeated purchase is assumed given that most consumers do not repeatedly purchase the same product in reality. Thus, the actual probability of attaining the expected product value more critically affects customer behaviour than does its expected value. The effectiveness of the research model is verified by conducting a survey on 300 online mall shoppers in Korea. The results confirm model effectiveness.     

A disturbance observer based practical coordinated tracking controller for uncertain heterogeneous multi‐agent systems

This paper presents a coordinated tracking controller for multi‐agent systems. We assume that agents are uncertain, nonidentical, and affected by external disturbances. The information available to the tracking controller is a weighted sum of relative measurements. A coordinated tracking controller based on the disturbance observer, which is known as a robust output feedback controller, is designed so that the disturbances acting on agents are attenuated and at the same time the weighted sum of relative measurements approximately satisfies a differential equation defined by the leader's dynamics, which results in practical coordinated tracking. Systematic design procedures of the controller as well as numerical simulations are provided. Copyright © 2014 John Wiley & Sons, Ltd.