There has been the expectation that polymers filled with small concentrations of nanosized particles will exhibit superior thermomechanical properties. We demonstrate that dispersing parts-per-million (ppm) polyhedral oligomeric silsesquioxane (POSS) nanochemicals by melt extrusion with polyolefins increased the tensile Young's modulus, yield stress, and toughness of blow molded and extruded films without penalizing extensibility, which is common to polymers reinforced with nano/microparticles. Transmission electron microscopy showed that the key to mechanical reinforcement is the spatial distribution of POSS at ca. single nanocage thus enabling interspersion of the macromolecular network. The thermal stability, water contact angle, and oxygen transmission of the films were also enhanced enabling a single component food package capable to keep food without decay for two weeks. The physical properties are improved when the nanoparticle size <D> is about the size of the virtual tube diameter dt, that is, <D>/dt ≈ 1. The enhancement of physical properties by placing the nanoparticle in the free space of the molecular network is a new paradigm in engineering polymer nanocomposites and opens opportunities for recyclable single component packaging films and tunable lightweight engineering and biomimetic materials. 相似文献
Confined foaming of poly(ethylene-co-vinyl acetate-co-carbon monoxide) using carbon dioxide as a physical blowing agent in a mold with either permeable or impermeable boundaries has been explored as a strategy to control final foam dimensions and morphology. The results are discussed in terms of comparisons to free-foaming experiments conducted at the same pressure and temperature conditions following the same pressurization and depressurization paths. Foaming experiments were carried out at 30 and 40°C and 100, 200, and 300 bar followed by rapid depressurization of the foaming cell. Confined foaming led to smaller pores with more uniform distributions across the polymer cross-section. However, bulk foam densities of the foams generated under confinement were higher than those generated under the free-foaming mode. Surface characteristics and skin layer formation were altered by expansion against both the permeable and impermeable boundaries. Confined foaming promotes uniform pore distribution and overall dimensional uniformity and may impart surface texture but the trade-off is in the degree to which the bulk foam density can be lowered. 相似文献
Journal of Chemical Ecology - The obligate pollination mutualism between Yucca and yucca moths is a classical example of coevolution. Oviposition and active pollination by female yucca moths occur... 相似文献
This paper reports on the structural, mechanical and tribological properties of molybdenum–copper nanocomposite films ‘doped’ with small amounts of nitrogen, which contain either no nitride phase (i.e. the nitrogen is held in interstitial solid solution, mainly in molybdenum) or small amounts of lower nitrides (i.e. Mo2N). All films were deposited on Si wafers, AISI M2 high speed steel and AISI 316 stainless steel by reactive sputtering using a hot-filament-enhanced dc unbalanced magnetron system. A systematic approach was adopted to investigate the evolution of metal/metal and ceramic/metal phase combinations with increasing nitrogen content (up to 40 at.% N) in the film. Coating composition and microstructure were determined by cross-sectional TEM, SEM and XPS. XRD was used to identify (where possible) metallic and metal-nitride phases. Mechanical properties such as hardness and elastic modulus were determined by low load Knoop and instrumented Vickers indentation measurements. Reciprocating sliding, micro-abrasion and impact tests were performed to assess tribological performance.
It was found that increasing the nitrogen gas flow rate from 0 to 15 sccm (and therefore nitrogen content in the film from 0 to 24 at.% N), refined significantly the coating microstructure from columnar to a dense and more equiaxed morphology, increasing the hardness whilst maintaining (almost constant) elastic modulus values, close to that of molybdenum metal. Further increases in the nitrogen gas flow rate resulted in films that appeared to contain significant fractions of the Mo2N ceramic phase. SEM and cross-sectional TEM analyses of the film deposited at a nitrogen flow rate of 20 sccm (containing 36 at.% N) demonstrated a microstructure consisting of 50–100 nm wide columns, which contain small regions of contrast in dark-field images, of the order of 3–5 nm wide. A maximum hardness of 32 GPa and the highest hardness/modulus ratio was however found in the (predominantly metallic) film deposited at a nitrogen gas flow rate of 15 sccm. This film also performed best in both micro-abrasion and impact wear tests; in contrast, the ‘ceramic’ film (deposited at 20 sccm nitrogen flow rate) performed better in reciprocating sliding wear. 相似文献
An advanced x-ray diffraction technique allows the development of texture components to be monitored and provides supplementary information about the cold work and residual stresses in cold-rolled copper sheet. The new technique confirms the results of an ultrasonic test, except for the ultrasonic test’s sensitivity to grain size. The new x-ray diffraction technique could be adapted to provide in-process, nondestructive evaluation of thin copper sheet, even for material moving at high speeds. 相似文献
Approximately 15 million cars and trucks reach the end of their useful life in the United States each year. More than 75%
of the materials from end-of-life vehicles are profitably recovered and recycled by the private sector; automotive materials
recycling is a success story. To achieve greater fuel efficiency and safety, today’s cars incorporate an increasing share
of innovative light-weight materials. While these materials greatly enhance efficiency during vehicle use, they can present
special challenges for recycling. These challenges will persist as automotive designs and the mix of materials used in vehicles
continue evolving to further improve safety and performance. To meet the challenges of automotive materials recycling, the
U.S. Department of Energy has recently expanded its collaborative research with industry in this area. This article discusses
this collaborative government/industry approach to sustainable end-of-life vehicle recycling.
For more information, contact Edward J. Daniels, Argonne National Laboratory, 9700 S. Cass Avenue, Building 362, Room C393,
Argonne, IL 60439-4815; (630) 252-5279; fax (630) 252-1342; e-mail edaniels@anl.gov. 相似文献
Water quality modelling facilitates our better understanding of the processes taking place in a lake system, and conservation plans to address them. The water quality analysis simulation programme (WASP) was used in this study to predict daily variations in water quality parameters, namely dissolved oxygen, nitrate, phosphate and chlorophyll‐a and biochemical oxygen demand concentrations in a tropical lake system. The lake was divided into eight segments with the respective morphological, environmental and flow details being model inputs. The monthly concentration of each water quality parameter also comprised model input. The model output was daily spatiotemporal variation in these parameters over a period of 476 days. This study also indicated that the occurrence of precipitation plays a major role in defining the water quality of a tropical lake. The heavy precipitation after a long gap, especially during the summer season, results in a large quantity of organic matter entering the lake through drains, thereby increasing the organic matter and phosphate in the water body, and subsequently resulting in high chlorophyll‐a concentrations in the lake. A reduced chlorophyll‐a concentration was observed during the heavy rains. The water quality fluctuations are more pronounced with precipitation, especially where polluted drains enter the lake. An improved water quality can be observed downstream, including increased dissolved oxygen and nitrate concentrations. Improved water quality was observed during the postmonsoon period, with increased salinity and dissolved oxygen concentrations, a finding that confirms generalized and specific conclusions can be achieved with the use of the WASP model. 相似文献
Statistical detection of mass malware has been shown to be highly successful. However, this type of malware is less interesting to cyber security officers of larger organizations, who are more concerned with detecting malware indicative of a targeted attack. Here we investigate the potential of statistically based approaches to detect such malware using a malware family associated with a large number of targeted network intrusions. Our approach is complementary to the bulk of statistical based malware classifiers, which are typically based on measures of overall similarity between executable files. One problem with this approach is that a malicious executable that shares some, but limited, functionality with known malware is likely to be misclassified as benign. Here a new approach to malware classification is introduced that classifies programs based on their similarity with known malware subroutines. It is illustrated that malware and benign programs can share a substantial amount of code, implying that classification should be based on malicious subroutines that occur infrequently, or not at all in benign programs. Various approaches to accomplishing this task are investigated, and a particularly simple approach appears the most effective. This approach simply computes the fraction of subroutines of a program that are similar to malware subroutines whose likes have not been found in a larger benign set. If this fraction exceeds around 1.5 %, the corresponding program can be classified as malicious at a 1 in 1000 false alarm rate. It is further shown that combining a local and overall similarity based approach can lead to considerably better prediction due to the relatively low correlation of their predictions. 相似文献
Research on better methods to digitally represent microscopic specimens has increased over recent decades. Opaque specimens, such as microfossils and metallurgic specimens, are often viewed using reflected light microscopy. Existing 3D surface estimation techniques for reflected light microscopy do not model reflectance, restricting the representation to only one illumination condition and making them an imperfect recreation of the experience of using an actual microscope. This paper introduces a virtual reflected-light microscopy (VRLM) system that estimates both shape and reflectance from a set of specimen images. When coupled with anaglyph creation, the system can depict both depth information and illumination cues under any desired lighting configuration. Digital representations are compact and easily viewed in an online setting. A prototype used to construct VRLM representations is comprised only of a microscope, a digital camera, a motorized stage and software. Such a system automatically acquires VRLM representations of large batches of specimens. VRLM representations are then disseminated in an interactive online environment, which allows users to change the virtual light source direction and type. Experiments demonstrate high quality VRLM representations of 500 microfossils. 相似文献