Cathode properties of metal trifluorides in Li and Na secondary batteries

Fluorine compounds have high discharge voltage due to its highly ionic metal-ligand bonds. In them, perovskite-type metal trifluorides with corner sharing matrix have large bottlenecks of diffusion pathways for intercalants. Iron trifluoride composites (FeF₃-C) prepared by planetary ball milling with carbon showed reversible charge/discharge behavior not only for Li, but also for Na anodes. X-ray diffraction and ⁵⁷Fe Mössbauer spectroscopy were applied to characterize the electrochemical properties of FeF₃ vs. Li and Na anodes. The cathode performances of the other commercially available transition metal trifluorides such as MF₃ (M = Ti, V, Mn, Co) have been also investigated.     

Measurement of the flood discharge of a small-sized river using an existing digital video recording system

In this study, a closed-circuit television (CCTV) system, installed for surveillance purposes, is utilized to measure the flow rate during a flood. The procedure to determine both the angle and scale-factor of the camera is described. Then, image analysis techniques, namely the direct visual measurement method, Large-Scale PIV (LSPIV) and Space-Time Image Velocimetry (STIV), are applied to the video images recorded by the CCTV camera. The results of these methods and the conventional float measurement are compared. In addition, the accuracy of the respective methods is discussed. A set of low-quality video images of a flood during a thunderstorm that occurred under the dark ambient conditions (midnight) is analyzed using three image-based methods. The transition of the flow rate during the event is successfully estimated.     

Development of two-dimensional mapping technique by in-air-PIXE with metal capillary

We have developed the two-dimensional mapping technique with in-air-PIXE (2D-PIXE) using a metal capillary as a guide to extract ion beam to air. The metal capillary is the conventional injection needle with a 200 μm inside diameter. For the target which is the character made of the copper wires on aluminum basement, 2D-PIXE measurements were performed by irradiating 3 MeV proton beam. As a result, the character was tend to be restored clearly by this method. We discuss about the result of the two-dimensional map from a viewpoint of the signal-to-noise ratio and the resolution. This technique is expected to be applicable to various fields such as biology, nano-technology, archeology and so on.     

Influence of temperature on the fatigue strength of compressed-hydrogen tanks for vehicles

The influence of environmental temperatures on the fatigue strength of compressed-hydrogen tanks for vehicles was investigated. The fatigue strength of Type-3 tanks was found to decrease in a low-temperature environment and increase in a high-temperature environment. The Type-3 tank has been subjected to autofrettage to improve fatigue strength. The investigation clarified that the effect of autofrettage changes according to the environmental temperature due to the difference between the coefficients of thermal expansion of carbon fiber reinforced plastic and aluminum alloy. This causes fatigue strength to change with changes in temperature. The Type-4 tank has a very long fatigue life and did not break after 45,000 cycles in a room-temperature or low-temperature environment. In a high-temperature environment, however, the tank broke in fewer than 45,000 cycles. The fatigue of carbon fiber reinforced plastic was promoted in the high-temperature environment, resulting in breakage of the tank. These results indicate that the fatigue strength of the tanks is influenced by the environmental temperature.     

A quantitative analysis of a trace amount of hydrogen in high temperature heat-treated carbons

A technique to determine a trace amount of hydrogen in carbon materials heat-treated above 1000 °C was developed. Three types of carbons prepared from poly(furfulyl alcohol), poly(vinyl chloride) and mesophase carbon microbeads were heat-treated at various temperatures ranging from 1000 to 1800 °C. Then they were gasified by O₂ in a fixed bed flow reactor, and the H₂O gases formed during the gasification processes were carefully monitored with a Karl Fischer moisture analyzer. As a result, this method makes it possible to determine the hydrogen contents in the carbons down to three places of decimals as a weight percent and can detect even a trace amount of hydrogen as low as 0.002 wt.%. A possible chemical structure of carbon edge sites was also discussed based on the experimentally determined hydrogen contents.     

Mechanical behavior of a single polymer chain in a non-solvent

Mechanical properties of a single polystyrene chain in mixtures of dioxane and methanol were measured with AFM. The effect of the solubility of the surrounding liquid on mechanical behavior of a polymer chain was examined. In good and Θ solvents, the force-extension curves exhibit a freely jointed chain (FJC)-like trend with good reproducibility. In a non-solvent, the profile of force-extension curve was dependent on the extension speed: an FJC-like nature emerged at the lower speed of 200 nm/s while saw-toothed curves were obtained at the higher speed of 2000 nm/s. The shape of saw-toothed curves varied from measurement to measurement. A force relaxation was also observed in the non-solvent under a fixed extension distance after 2000 nm/s extension. The mechanical behavior in non-solvents suggests that inhomogeneous deformation of a PS chain occurs due to reduction of the chain mobility.     

Preparation of avidin-containing polyelectrolyte microcapsules and their uptake and release properties

Avidin-containing polyelectrolyte microcapsules were prepared by a layer-by-layer deposition technique and uptake and release of biotin-labelled fluorescein (b-FITC) was studied. The polyelectrolyte microcapsules were prepared by coating the surface of calcium carbonate (CaCO₃) microparticles containing avidin-poly(styrene sulfonate) (PSS) conjugate, followed by dissolution of CaCO₃ core in an ethylenediaminetetraacetic acid solution. Release of avidin from the microcapsules was markedly suppressed due to formation of a high molecular weight of avidin-PSS conjugate in the microcapsules. The uptake of b-FITC into the microcapsules was highly enhanced through a strong binding of b-FITC to avidin, as compared to the uptake into avidin-free microcapsules. Release of b-FITC from the microcapsules was accelerated upon addition of biotin, 2-iminobiotin, or lipoic acid in the solution due to the competitive binding of the additives to the binding site of avidin.     

Molecular recognition by wall-assembling-type nanocavity in aqueous media

Steroid cyclophanes, each having a macrocyclic ring attached to four bile acid moieties via chiral lysine connectors, were synthesized, and the binding of the 2-naphthylphenylketone (guest) to the steroid cyclophanes in water was investigated. The circular dichroism spectra of the steroid cyclophane with cholic acid and L-lysine were significantly affected by the binding of the guest, and the induced circular dichroism based on the absorption of the achiral guest was also observed. The binding of the guest to the steroid cyclophane with cholic acids and D-lysines induced changes in the circular dichroism spectra with the opposite sign of the molecular ellipticities. An induced circular dichroism spectral change was not observed upon binding of the guest to the analogous host without OH sites. These results strongly suggest that the guest is conformationally fixed through hydrogen bonding between the carbonyl group of the guest and the steroidal hydroxyl group of the host. The assembly of only four steroid residues on the macrocyclic ring probably provided a hydrophobic nanocavity for hydrogen bonding.     

Standardized evaluation of chemical compositions of LiTaO3 single crystals for SAW devices using the LFB ultrasonic material characterization system

The line-focus-beam ultrasonic material characterization (LIFB-UMC) system is applied to compare and evaluate tolerances provided independently for the Curie temperature T/sub C/ and lattice constant /spl alpha/ to evaluate commercial LiTaO/sub 3/ single crystals by measuring the Rayleigh-type leaky surface acoustic wave (LSAW) velocities V/sub LSAW/. The relationships between VLSAW, and T/sub C/ and /spl alpha/ measured by individual manufacturers were obtained experimentally using 42/spl deg/YX-LiTaO/sub 3/ wafers as specimens from three crystal manufacturers. In addition, the relationship between VLSAW and SH-type SAW velocities V/sub SAW/ that are actually used for the SAW device wafers was obtained through calculations, using the chemical composition dependences of the acoustical physical constants for LiTaO/sub 3/ crystals reported previously. The result of a comparison between the T/sub C/ tolerance of /spl plusmn/3/spl deg/C and the /spl alpha/ tolerance of /spl plusmn/0.00002 nm through the common scale of VLSAW or VSAW demonstrated that the /spl alpha/ tolerance is 1.6 times larger than the T/sub C/ tolerance. Furthermore, we performed a standardized comparison of statistical data of T/sub C/ and /spl alpha/ for LiTaO/sub 3/ crystals grown by two manufacturers during 1999 and 2000, using VLSAW. The results clarified the differences of the average chemical compositions and of the chemical composition distributions among the crystal ingots between the two manufacturers. A guideline for the standardized evaluation procedure has been established for the SAW-device wafer specifications by the LFB-UMC system.