Near-ML multiuser detection with linear filters and reliability-based processing

The prohibitive - exponential in the number of users - computational complexity of the maximum-likelihood multiuser detector for direct-sequence code-division multiple-access communications has fueled an extensive research effort for the development of low-complexity multiuser detection alternatives. We show that we can efficiently and effectively approach the error rate performance of the optimum multiuser detector as follows. We utilize a multiuser zero-forcing or minimum mean-square error (MMSE) linear filter as a preprocessor and we establish that the output magnitudes, when properly scaled, provide a reliability measure for each user bit decision. Then, we prepare an ordered, reliability-based error search sequence of length linear in the number of users; it returns the most likely user bit vector among all visited options. Numerical and simulation studies for moderately loaded systems that permit exact implementation of the optimum detector indicate that the error rate performance of the optimum and the proposed detector are nearly indistinguishable over the whole predetection. signal-to-noise ratio range of practical interest. Similar studies for higher user loads (that prohibit comparisons with the optimum detector) demonstrate error rate performance gains of orders of magnitude in comparison with straight decorrelating or MMSE multiuser detection.     

Fringing in tubular permanent-magnet machines: Part I. Magnetic field distribution, flux linkage, and thrust force

This paper extends an analysis developed for tubular permanent-magnet machines to account for the effect of fringing associated with the finite length of the ferromagnetic armature core. The magnetic field distribution, established by using an analytical technique formulated in the cylindrical coordinate system, provides an accurate means of evaluating the effect of the fringing flux on the thrust force and the back-electromotive force. Finite-element calculations confirm the analytically derived results. In Part II of the paper, the analysis is used to predict the cogging force that results from end effects and to facilitate minimization of the force.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

Design procedure of class-E amplifier for off-nominal operation at 50% duty ratio

Design equations for satisfying the off-nominal operating condition [i.e., only the zero-voltage switching (ZVS) condition] of the Class-E amplifier with a linear shunt capacitance at a duty ratio D=0.5 are derived. A new parameter s (V/s), called the slope of switch voltage when the switch turns on is introduced to obtain an image of the distance from the nominal conditions. By examining off-nominal Class-E operation degree of the design freedom of the Class-E amplifier increases by one. In addition various amplifier parameters such as operating frequency, output power, and load resistance range can be set as design specifications. For example, the peak switch voltage and switch current can be taken into account in the design procedure. Examples of a design procedure of the Class-E amplifier for off-nominal operation are given. The theoretical results were verified with PSpice simulation and experiments.     

Mobile Device Security Using Transient Authentication

Mobile devices are vulnerable to theft and loss due to their small size and the characteristics of their common usage environment. Since they allow users to work while away from their desk, they are most useful in public locations and while traveling. Unfortunately, this is also where they are most at risk. Existing schemes for securing data either do not protect the device after it is stolen or require bothersome reauthentication. Transient Authentication lifts the burden of authentication from the user by use of a wearable token that constantly attests to the user's presence. When the user departs, the token and device lose contact and the device secures itself. We show how to leverage this authentication framework to secure all the memory and storage locations on a device into which secrets may creep. Our evaluation shows this is done without inconveniencing the user, while imposing a minimal performance overhead     

A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

Web Services Architecture

The underlying need for Web Services has been demonstrated by their early adoption and rapid evolution during the last few years. This evolution has resulted in a number of specifications being proposed that at first glance seem independent of one another. The current immaturity of the base technology and the growing number and diversity of specifications related to Web Services is sometimes seen as a barrier to developers attempting to combine them to create a working piece of software. For some, the apparent lack of stability and coherence in the specifications even raises the question of the real long-term viability and value of the technology. This document puts those specifications into perspective by describing the set of interoperable XML protocols that are the foundation of building interoperable systems, middleware, and applications. This revised version was published online in July 2006 with corrections to the Cover Date.