The effect of grain size, strain rate, and temperature on the mechanical behavior of commercial purity aluminum

Commercial purity aluminum AA1050 was subjected to equal channel angular extrusion (ECAE) that resulted in an ultrafine-grained (UFG) microstructure with an as-received grain size of 0.35 μm. This UFG material was then annealed to obtain microstructures with grain sizes ranging from 0.47 to 20 μm. Specimens were compressed at quasi-static, intermediate, and dynamic strain rates at temperatures of 77 and 298 K. The mechanical properties were found to vary significantly with grain size, strain rate, and temperature. Yield stress was found to increase with decreasing grain size, decreasing temperature, and increasing strain rate. The work hardening rate was seen to increase with increasing grain size, decreasing temperature, and increasing strain rate. The influence of strain rate and temperature is most significant in the smallest grain size specimens. The rate of work hardening is also influenced by strain rate, temperature, and grain size with negative rates of work hardening observed at 298 K and quasi-static strain rates in the smallest grain sizes and increasing rates of work hardening with increasing loading rate and grain size. Work hardening behavior is correlated with the substructural evolution of these specimens.     

Interview mit Hans-Christian Boos zum Thema „Unternehmertum in der IT-Branche“

Ohne Zusammenfassung     

Sensor guided handling and assembly of active micro-systems

Positioning accuracies in the range of a few micrometers and below are necessary for the assembly of active micro-systems. In order to reach these accuracies, an assembly system for sensor guided micro-assembly is developed in the Collaborative Research Centre 516 “Design and manufacturing of active micro-systems”. The combination of a parallel robot with an integrated 3D vision sensor and a micro-gripper enables to reach relative positioning accuracies below 1 μm.     

Comprehensive heat exchange model for a semiconductor laser diode

By measuring the total energy flow from an optical device, we can develop new design strategies for thermal stabilization. Here we present a comprehensive model for heat exchange between a semiconductor laser diode and its environment that includes the mechanisms of conduction, convection, and radiation. We perform quantitative measurements of these processes for several devices, deriving parameters such as a laser's heat transfer coefficient, and then demonstrate the feasibility of thermal probing for the nondestructive wafer-scale characterization of optical devices.     

Growing of Tubes with a Small Inner Diameter from the Melt by the Stepanov Method

A mathematical model is suggested for describing the growth of a crystal tube with a small inner diameter from the melt by the modified Stepanov method with the tube being affected by temperature pulses. The behavior of the inner and outer radii of the tube as a function of the amplitude and duration of temperature jumps is studied.     

Pilot: probabilistic lightweight group communication system for ad hoc networks

Providing reliable group communication is an ever recurring topic in distributed settings. In mobile ad hoc networks, this problem is even more significant since all nodes act as peers, while it becomes more challenging due to highly dynamic and unpredictable topology changes. In order to overcome these difficulties, we deviate from the conventional point of view, i.e., we "fight fire with fire," by exploiting the nondeterministic nature of ad hoc networks. Inspired by the principles of gossip mechanisms and probabilistic quorum systems, we present in this paper PILOT (probabilistic lightweight group communication system) for ad hoc networks, a two-layer system consisting of a set of protocols for reliable multicasting and data sharing in mobile ad hoc networks. The performance of PILOT is predictable and controllable in terms of both reliability (fault tolerance) and efficiency (overhead). We present an analysis of PILOT's performance, which is used to fine-tune protocol parameters to obtain the desired trade off between reliability and efficiency. We confirm the predictability and tunability of PILOT through simulations with ns-2.     

Capture of Organic Vapors Using Adsorption and Electrothermal Regeneration

Activated-carbon-fiber cloth (ACFC) is an alternative adsorbent to granular activated carbon (GAC) for removing and recovering organic vapors from gas streams. Electrothermal desorption (ED) of ACFC provides rapid regeneration while requiring less energy compared to traditional regeneration techniques used with GAC. This paper provides proof-of-concept results from a bench-scale ACFC adsorption system. The automated system captured 1,000 ppmv of hazardous air pollutants/volatile organic compounds (HAPs/VOCs) from air streams and demonstrated the use of ED, using ac voltage, to recover the HAP/VOC as a pure liquid. The desorbed HAP/VOC condensed onto the inner walls of the adsorber and was collected at the bottom of the vessel, without the use of ancillary cooling. Seventy percent of the HAP/VOC was collected per cycle as condensate, with the balance being retained in the regenerated adsorber or recycled to the second adsorber. ED with in-vessel condensation results in minimal N2 consumption and short regeneration cycle times allowing the process to be cost competitive with conventional GAC-based adsorption processes. This technology extends the application of carbon adsorption systems to situations that were previously economically and physically impractical.     

In situ TEM observations of fracture in nanolaminated metallic thin films

Fracture of single crystal nanolaminated thin films has been investigated through in situ straining of cross-sectional samples of Cu/Ni nanolaminates grown on Cu (001) single crystal substrates. The earlest stages of deformation exhibits a confined layer slip mechanism. With continued straining, unstable fracture occurs creating a mixed-mode crack that propagates across the nanolaminate, roughly perpendicular to the interfaces. Eventually, stable crack growth with intense plastic deformation ahead of the crack tip occurs over many bilayers in the direction of crack growth. Simultaneously, plasticity was seen to spread only 1 or 2 bilayer distances normal to the crack, creating an extremely localized plastic zone. Transmission electron microscopic (TEM) examination after the test did not reveal the presence of dislocations in the crack wake, except where severe crack deflection was observed. By comparison, the plastic zone size in the substrate was greater by several of orders of magnitude.     

Optoelectronic Method of Noncontacting Reconstruction of the Profile of a Surface of Three Dimensional Objects of Large Dimensions

An optoelectronic method is considered for noncontacting reconstruction of the surface profile of three-dimensional objects of large dimensions. The optimal conditions for performing measurements are identified. It is shown that the proposed method, in contrast to the already known methods, does not require fine tuning of the equipment. A numerical method is given for compensating distortions caused by aberrations. A method is described for reconstructing the surface profile cell by cell which increases the accuracy of measurements.