Distribution of mineral species in different coal seams of Talcher coalfield and its transformation behavior at varying temperatures

International Journal of Coal Science & Technology - Mineral phase characterization and thorough understanding of its transformation behavior during combustion are imperative to know the...     

Column Kinetic Tests Assessing Geochemical Behavior of Mine Wastes in the Jerada Coal District (Morocco)

The Jerada anthracite mine in Morocco was abandoned in 2001 after producing approximately 20 million tonnes of solid waste. The acid generating potential of these wastes was determined by performing tests on five samples collected from relatively older and more recent waste deposits. No carbonate minerals were identified. Pyrite was the only sulphide mineral observed and much of it had been completely transformed into Fe-oxides. Analysis of the waste indicated low levels (<1 %) of Ca and Mg, while Fe and Al concentrations generally exceeded 5 %. Modified Sobek static tests and column kinetic tests were conducted for 24 months. The static test results were not conclusive (20 <net neutralising potential <20 Kg CaCO₃/t). Leachates from the kinetic tests for three of the five samples showed an initially acidic pH, while those of the remaining two became acidic by the end of the tests. Sulfate concentrations (SO₄ ^2?) decreased over time from 5000 to 200 mg/L.     

Prediction of seepage water pressure for slope stability at the Gol-E-Gohar open pit mine

Slope stability accidents are one of the leading causes of destruction at open pit mining operations. Such interception of the seepage water results in the water inflow from the surrounding aquifer towards the mine excavations. In order to design an effective drainage scheme for an open pit mine, prediction of water inflow into the pit is essential. These changes have resulted in some failures and instability problems in different parts of Gol-E-Gohar iron open pit mine. It seems that main parameters which effect the failure and instability of the mine slopes are high pressure of groundwater and system of discontinuities (faults, joins, and bedding planes), which intersect the pit walls. The analysis results indicate that stability of the final pit slopes is sensitive to multi-planar failures and confined water in the walls pit is also a factor adversely affecting the stability. Problems associated with groundwater at the site were also assessed with the analyses of piezometric level and groundwater inflow.     

The Effects of Annealing After Equal Channel Angular Extrusion (ECAE) on Mechanical and Magnetic Properties of 49Fe-49Co-2V Alloy

Metallurgical and Materials Transactions A - Equal channel angular extrusion (ECAE) of 49Fe-49Co-2V, also known as Hiperco® 50A or Permendur-2V, greatly improves the strength and ductility of...     

Microstructure-Based Estimation of Strength and Ductility Distributions for $$\alpha +\beta $$ Titanium Alloys

Titanium alloys are processed to develop a wide range of microstructure configurations and therefore material properties. While these properties are typically measured experimentally, a framework for property prediction could greatly enhance alloy design and manufacturing. Here a microstructure-sensitive framework is presented for the prediction of strength and ductility as well as estimates of the bounds in variability for these properties. The framework explicitly considers distributions of microstructure via new approaches for instantiation of structure in synthetic samples. The parametric evaluation strategy, including the finite element simulation package FEpX, is used to create and test virtual polycrystalline samples to evaluate the variability bounds of mechanical properties in Ti-6Al-4V. Critical parameters for the property evaluation framework are provided by measurements of single crystal properties and advanced characterization of microstructure and slip system strengths in 2D and 3D. Property distributions for yield strength and ductility are presented, along with the validation and verification steps undertaken. Comparisons between strain localization and slip activity in virtual samples and in experimental grain-scale strain measurements are also discussed.

     

High Temperature Oxidation Behavior of Conventional and Nb-Modified MAR-M246 Ni-Based Superalloy

The present investigations focused on the thermal oxidation of two variants of MAR-M246 alloy having the same contents of Ta and Nb in at. pct, considering the effects of total replacement of Ta by Nb. The alloys were produced by investment casting using high purity elements in induction furnace under vacuum atmosphere. The alloys were oxidized pseudo-isothermally at 800 °C, 900 °C and 1000 °C up to 1000 hours under lab air. Protective oxidation products growing on the surface of the oxidized samples were mainly Al₂O₃, Cr₂O₃. Other less protective oxide such as spinels (NiCr₂O₄ and CoCr₂O₄) and TiO₂ were also detected as oxidation products. The conventional alloy exhibited slight internal oxidation at 800 °C and an enhanced resistance at 900 °C and 1000 °C. The Nb-modified alloy presented an exacerbated internal oxidation and nitridation at 900 °C and 1000 °C and an enhanced resistance at 800 °C. At 1000 °C, Nb-modified alloy was particularly affected by excessive spalling as the main damage mechanisms. From a kinetic point of view, both alloys exhibit the same behavior at 800 °C and 900 °C, with k_p values typical of alumina forming alloys (2 × 10⁻¹⁴ to 3.6 × 10⁻¹³ g² cm⁻⁴ s⁻¹). However, Ta modified alloys exhibited superior oxidation resistance at 1000 °C when compared to the Nb modified alloy due to better adherence of the protective oxide scale.

     

Effect of Thermomechanical Fatigue on Precipitation Microstructure in Two Precipitation-Hardened Cast Aluminum Alloys

Thermal loading induces modifications of the precipitation microstructure of Al–Si–Cu–Mg alloys. This study focuses on the effect of deformation on precipitation microstructure during thermomechanical loadings. Several specimens were thermomechanically cycled while others were exposed to the same thermal cycles without any mechanical loading. The nature and morphological characteristics of the precipitation microstructure of the thermomechanically cycled specimens are compared to those of the thermally aged ones, using transmission electron microscopy (TEM), in order to assess the effect of deformation on the precipitation microstructure and especially on the kinetics of precipitate growth. The absence of any significant effect of superimposed straining during thermal cycling is discussed. Implications for the prevision of yield strength degradation during service operation are briefly presented.

     

Accelerated Design of Eutectic High Entropy Alloys by ICME Approach

Eutectic high entropy alloy with seven components is designed based on the integrated computational materials engineering (ICME) framework. The framework includes thermodynamic prediction using calculation of phase diagrams (CALPHAD), microstructure simulation using phase-field method, and experimental validation. The designed alloy shows the eutectic structure consisting of FCC and laves phase in the composition range from 8.25 to 10 at. pct Ta. The simulation and experimental results are co-related and a framework is proposed that can be used for high entropy alloy design subjected to various manufacturing processes.

     

Buckling-Induced Delamination of TiN Film on Stainless Steel in the Presence of Stress Concentration

TiN coating is provided by reactive magnetron coating on a 304 stainless steel sample with a notch introduced at the edge of the sample. The sample is subjected to a tensile stress close to that of yield strength of the stainless steel. Optical and scanning electron microscopy characterization showed the distribution of buckled and delaminated regions around the notch. The distribution of the size of the partially delaminated regions of the film on the substrate is determined by transient thermo-reflectance. The stress field due to the notch is represented by that of a circular hole present at the tip and the variation of compressive and shear strain as a function of radial and angular coordinates is determined. The distribution of buckled and delaminated regions is found to follow the compressive strain variation around the notch. The size of the partially delaminated film is found to be larger near the notch and decreased with distance from the notch. The results illustrate that structures with regions of stress concentration should not be provided with brittle protective coatings that will delaminate.

     

Plastic Deformation Resistance of Steel Grades EP450-Sh and EP823-Sh in Hot and Cold State

Metallurgist - The article presents the results of plastometric studies on hot deformation and studies on the hardening curves in cold deformation of EP450-Sh (12H12M1BFR-Sh) and EP823-Sh...