Spectral analysis methods for vehicle interior vibro-acoustics identification

Noise has various effects on comfort, performance and health of human. Sound are analysed by human brain based on the frequencies and amplitudes. In a dynamic system, transmission of sound and vibrations depend on frequency and direction of the input motion and characteristics of the output. It is imperative that automotive manufacturers invest a lot of effort and money to improve and enhance the vibro-acoustics performance of their products. The enhancement effort may be very difficult and time-consuming if one relies only on ‘trial and error’ method without prior knowledge about the sources itself. Complex noise inside a vehicle cabin originated from various sources and travel through many pathways. First stage of sound quality refinement is to find the source. It is vital for automotive engineers to identify the dominant noise sources such as engine noise, exhaust noise and noise due to vibration transmission inside of vehicle. The purpose of this paper is to find the vibro-acoustical sources of noise in a passenger vehicle compartment. The implementation of spectral analysis method is much faster than the ‘trial and error’ methods in which, parts should be separated to measure the transfer functions. Also by using spectral analysis method, signals can be recorded in real operational conditions which conduce to more consistent results. A multi-channel analyser is utilised to measure and record the vibro-acoustical signals. Computational algorithms are also employed to identify contribution of various sources towards the measured interior signal. These achievements can be utilised to detect, control and optimise interior noise performance of road transport vehicles.     

An ANFIS-based approach for predicting the bed load for moderately sized rivers

A total of 346 sets of bed-load data obtained from the Kinta River, Pari River, Kerayong River and Langat River were analyzed using four common bed-load equations. These assessments, based on the median sediment size (d₅₀), show that the existing equations were unable to predict the measured bed load accurately. All existing equations over-predicted the measured values, and none of the existing bed-load equations gave satisfactory performance when tested on local river data. Therefore, the present study applies a new soft computing technique, i.e. an adaptive neuro-fuzzy inference system (ANFIS), to better predict measured bed-load data. Validation of the developed network (ANFIS) was performed using a new set of bed-load data collected at Kulim River. The results show that the recommended network can more accurately predict the measured bed-load data when compared to an equation based on a regression method.     

Copper(II)‐Catalyzed Aerobic Oxidative Coupling between Chalcone and 2‐Aminopyridine via C?H Amination: An Expedient Synthesis of 3‐Aroylimidazo[1,2‐a]pyridines

A simple and efficient protocol has been developed for the synthesis of 3‐aroylimidazopyridines via copper(II) acetate‐catalyzed aerobic oxidative amination. A library of 3‐aroylimidazopyridines was synthesized from readily accessible chalcones and 2‐aminopyridines with high yields and regioselectivity. The reaction proceeds through a tandem Michael addition followed by an intramolecular oxidative amination. The successful application of this methodology for a gram‐scale reaction indicates its potential for bulk synthesis.

     

Determination of oil palm fruit phenolic compounds and their antioxidant activities using spectrophotometric methods

There is scarce information on the phenolics of oil palm fruits (Elaeis guineensis). In this study, phenolics were extracted from oil palm fruits and analysed using spectrophotometry for information on the different types of palm phenolics and their antioxidative activities. Analyses of the total phenolic content (TPC), total flavonoid content (TFC), o‐diphenols index, hydroxycinnamic acid index, flavonols index and phenol index showed ranges between 5.64 and 83.97 g L^?1 gallic acid equivalent (GAE), 0.31–7.53 g L^?1 catechin equivalent, 4.90–93.20 g L^?1 GAE, 23.74–77.46 g L^?1 ferulic acid equivalent, 3.62–95.33 g L^?1 rutin equivalent and 15.90–247.22 g L^?1 GAE, respectively. The antioxidant assay, 2,2‐diphenyl‐2‐picrylhydrazyl radical scavenging assay, showed antioxidative activities in all the extracts with results ranging from 4.41 to 61.98 g L^?1 trolox equivalent. The high antioxidant activities of the oil palm fruit phenolics were also found to increase with increasing TPC and TFC.     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Energy absorption and failure response of silk/epoxy composite square tubes: Experimental

This paper focuses on natural silk/epoxy composite square tubes energy absorption and failure response. The tested specimens were featured by a material combination of different lengths and same numbers of natural silk/epoxy composite layers in form of reinforced woven fabric in thermosetting epoxy resin. Tubes were compressed in INSTRON 5567 with a loading capacity of 30 kN. This research investigates the influence of the wall lengths on the compressive response and also failure mode of the tested tubes are analysed. The load–displacement behaviour of square tubes recorded during the test. Since natural woven silk has been used as textile in centuries but due to rare study of this fabric as reinforcement material for composites, the results of this paper can be considerable. Outcomes from this paper might be helpful to guide the design of crashworthy structures.     

Developing a method to generate semi-distributed layouts by genetic algorithm

Recent research in industries shows that existing layout configurations do not satisfy the needs of multi-product enterprises in turbulent environments but within new layout strategies, distributed layouts have deserved more attention in most manufacturing environments and have a promising potential to cope with demand disturbances. This study is an attempt to design weighted distributed layouts via considering machine independent capabilities by a resource elements (REs) approach, which has caused generation of a new type of distributed layout named semi-distributed layout. REs are used to define processing requirements of parts and processing capabilities of machines. Another contribution of this paper is applying genetic algorithms (GAs) to distribute REs to find the optimal assignment of machines to available locations in such a way the travelled distances of parts are minimised and the accessibility of them to the required machines are maximised. The methodology of this paper is illustrated using a two-phase procedure. First, all machining facilities are divided into a set of REs based on their capabilities and second, the weighted connections among REs are considered to distribute them over the floor through implementing the developed GA. To evaluate the methodology, the proposed algorithm is tested with three illustrative examples obtained from the literature, in which two of them are comparable with outputs of simulated annealing (SA). The comparison between the outputs of the GA and the SA on the same cases presents that for large size problems, the GA significantly outperforms the SA.     

Failure assessment on offshore girth welded pipelines due to corrosion defects

Corrosion is an electrochemical process in offshore pipelines where the material strength begins to decrease as corrosion advances. Numerous studies have been performed to determine the remaining strengths (failure pressure) of corroded pipelines. Currently the axial corrosions of the girth welded pipelines still leave much to be understood. This study attempted to simulate girth welded pipeline with various corroded depths and lengths in order to compare with offshore pipeline design manuals. Based on the numerical results, the influence of corrosion defects parameters on remaining strengths were investigated for girth welded pipelines. The investigation on the effect of strength mismatch revealed that in the cases of under‐matched, higher failure pressures are obtained. Comparisons of current results with B31G‐2012 and DNV‐RP‐F101 demonstrated that both codes may produce somewhat conservative predictions on the failure pressure. Furthermore, an equation was proposed to evaluate the corrosion progress across girth welded pipelines.     

A multi-period scheduling method for trading-off between skilled-workers allocation and outsource service usage in dynamic CMS

In this paper, a new method is proposed for short-term period scheduling of dynamic cellular manufacturing systems in a dual resource constrained environment. The aim of this method is to find best production strategy of in-house manufacturing using worker assignment (both temporary and skilled workers) and outsourcing, while part demands are uncertain and can be varied periodically. For this purpose, a multi-period scheduling model has been proposed which is flexible enough to use in real industries. To solve the proposed problem, a number of metaheuristics are developed including Branch and Bound; a hybrid Tabu Search and Simulated Annealing algorithms and a hybrid Ant Colony Optimization and Simulated Annealing algorithms. A Taguchi method (L₂₇ orthogonal optimisation) is used to estimate parameters of the proposed method in order to solve experiments derived from the literature. For evaluating the system imbalance in dynamic market demands, a new measuring index is developed. Our findings indicate that the uncertain market demands affects the part allocating which may induce workstation-load variations that yield to cell-load variation accordingly. To solve this problem, two methods are offered. The results show that promoting staff and using freezing technique are promising ways to reduce system imbalance while confronting with the mentioned condition. The outcomes also show the superiority of the proposed hybrid method in providing solutions with better quality.