Development of µGC (micro gas chromatography) with high performance micromachined chip column

A micro gas chromatography (µGC) instrument applying a high performance chip column fabricated on a silicon wafer was developed. Experimental results of the chip column and protyping of a µGC instrument are described. Approximately 35 000 theoretical plates were generated with the chip column coated liquid phase (5% phenyl-/95% dimethyl-polysiloxane). The theoretical plates of the chip column were close to those of the capillary column. Experimental minimum height equivalent to a theoretical plate (HETP, H_min) of the chip column was 1.2 times higher than the calculated H_min. A prototype µGC applying the chip column was developed. The µGC generated approximately 35 000 theoretical plates, similar to the theoretical plates obtained by a commercial GC instrument. Copyright © 2009 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Effect of the preparation condition on the properties of titania-silica derived from tetraisopropyl titanate(IV) and tetraethyl orthosilicate

Titania-silica mixed oxide was prepared by hydrolyzing tetraethyl orthosilicate and tetraisopropyl titanate(IV) with a mixture of ethanol and 0.01 N aqueous acetic acid. Surface Ti content, BET surface area, and the number of acid sites increased with an increase in 0.01 N aqueous acetic acid. Thus hydrolysis of both alkoxides occurred simultaneously with a large amount of the acetic acid solution, and there was extensive interaction between TiO₂ and SiO₂ phases. With small amount of 0.01 N aqueous acetic acid, however, titanium hydroxide was first formed and, then, it was covered with the silica phase produced in a later stage of the hydrolysis. Increase in the acetic acid solution also led to the formation of a large amount of tetrahedral Ti species, which were active for the epoxidation of oct-1-ene usingt-butyl hydroperoxide as an oxidant.     

Hyperbranched poly(cyanurateamine): A new corrosion inhibitor for mild steel in hydrochloric acid medium

Hyperbranched poly(cyanurateamine) (POCYAM) was tested as a novel corrosion inhibitor for mild steel in 0.5–3 M HCl using chemical and electrochemical techniques at 25–70 °C. The results show that this compound has good corrosion inhibiting properties for mild steel in HCl at very low concentrations. Corrosion inhibition efficiency rises with POCYAM concentration. The adsorption of the POCYAM onto the mild steel surface obeys Langmuir adsorption isotherm model. The inhibition mechanism was further corroborated by the values of thermodynamic parameters obtained from the experimental data.     

Real-time measurements of local myocardium motion and arterial wall thickening

We have already developed a new method, namely, the phased tracking method, to track the movement of the heart wall and arterial wall accurately based on both the phase and magnitude of the demodulated signals to determine the instantaneous position of an object. This method has been realized by an off-line measurement system, which cannot be applied to transient evaluation of rapid response of the cardiovascular system to physiological stress. In this paper, therefore, a real-time system to measure change in the thickness of the myocardium and the arterial wall is presented. In this system, an analytic signal from standard ultrasonic diagnostic equipment is analogue-to-digital (A/D) converted at a sampling frequency of 1 MHz. By pipelining and parallel processing using four high-speed digital signal processing (DSP) chips, the method described is realized in real time. The tracking results for both sides of the heart and/or arterial wall are superimposed on the M (motion)-mode image in the work station (WS), and the thickness changes of the heart and/or arterial wall are also displayed and digital-to-analogue (D/A) converted in real time. From the regional change in thickness of the heart wall, spatial distribution of myocardial motility and contractility can be evaluated. For the arterial wall, its local elasticity can be evaluated by referring to the blood pressure. In in vivo experiments, the rapid response of the change in wall thickness of the carotid artery to the dose of the nitroglycerine (NTG) is evaluated. This new real-time system offers potential for quantitative diagnosis of myocardial motility, early stage atherosclerosis, and the transient evaluation of the rapid response of the cardiovascular system to physiological stress.     

Adaptive Ray‐bundle Tracing with Memory Usage Prediction: Efficient Global Illumination in Large Scenes

This paper proposes an adaptive rendering technique for ray‐bundle tracing. Ray‐bundle tracing can be done by per‐pixel linked‐list construction on a GPU rasterization pipeline. This rasterization based approach offers significant benefits for the efficient generation of light maps (e.g., hardware acceleration, tessellation, and recycling of shaders used in real‐time graphics). However, it is inapplicable to large and complex scenes due to the limited capacity of the GPU memory because it requires a high‐resolution frame buffer and high‐capacity node buffer for the linked‐lists. In addition, memory overflow can potentially occur on the per‐pixel linked‐list since the memory usage of the lists is usually unknown before the rendering process. We introduce an adaptive tiling technique with memory usage prediction. Our method uses an appropriately tiled frame buffer, thus eliminating almost all of the overflow risks thanks to our adaptive tile subdivision scheme. Using this technique, we are able to render high‐quality light maps of large and complex scenes which cannot be computed using previous ray‐bundle based methods.     

Development Of Cvt Control System And Its Use For Fuel‐Efficient Operation Of Engine

Continuously variable transmission (CVT) provides an automobile with the ability to change the gear ratio continuously, which can then improve not only ride quality such as acceleration performance but also fuel‐efficiency. However, to take advantage of the ability, a control system that can precisely control the gear ratio is required. This paper proposes such a control system for a belt‐driven CVT system. For controller design, first the CVT system is modeled by analytical and experimental approaches. The resultant static and dynamic characteristics provide a nonlinear first‐order model with an uncertain time constant and time delay. The nonlinear steady‐state gain is adjusted to one by a gain‐scheduled pre‐compensator. Thereby the plant model becomes a linear first‐order lag system with a dead time. The next step is controller design using the plant model. To guarantee stability and control performance against the parameter variation and time delay, the μ‐synthesis, a robust control method, is employed for feedback control. In addition, a feedforward controller is incorporated into the feedback control system to obtain better output response. The feedforward controller is given by a combination of the inverse system of the plant and a reference model that gives desired output response. As a result, the control system becomes a two‐degree‐of‐freedom control system. To evaluate the performance of the control system and its effectiveness on the fuel‐efficiency, computer simulation and driving tests were conducted. The simulation and experiment results prove that the proposed control system can make the gear ratio track a reference output quickly and precisely in the presence of the uncertainties. The results also show that the control system improves fuel‐efficiency by changing the gear ratio so that the engine torque and its revolution speed can satisfy optimum‐efficiency operating condition.     

Further discussion on magnetic vector potential finite-elementformulation for three-dimensional magnetostatic field analysis

A linear soft-iron and current model called the IEE Japan model using a novel vector potential finite-element formulation is examined. Calculated and measured results are in close agreement. For comparison, the same model was calculated by the conventional variational formulation. The divergence of magnetic vector potential equals zero at the boundary of different materials and the values themselves are small enough at the Gaussian quadratural points, which means that uniqueness of the solution is guaranteed. The gauge condition is determined by the formulation, not by the boundary conditions. The new formulation requires less computing time and memory than the conventional variational formulation     

Phantom experiments on a PSAPD-based compact gamma camera with submillimeter spatial resolution for small animal SPECT

We demonstrate a position sensitive avalanche photodiode (PSAPD) based compact gamma camera for the application of small animal single photon emission computed tomography (SPECT). The silicon PSAPD with a two-dimensional resistive layer and four readout channels is implemented as a gamma ray detector to record the energy and position of radiation events from a radionuclide source. A 2 mm thick monolithic CsI:Tl scintillator is optically coupled to a PSAPD with a 8mm×8mm active area, providing submillimeter intrinsic spatial resolution, high energy resolution (16% full-width half maximum at 140 keV) and high gain. A mouse heart phantom filled with an aqueous solution of 370 MBq (99m)Tc-pertechnetate (140 keV) was imaged using the PSAPD detector module and a tungsten knife-edge pinhole collimator with a 0.5 mm diameter aperture. The PSAPD detector module was cooled with cold nitrogen gas to suppress dark current shot noise. For each projection image of the mouse heart phantom, a rotated diagonal readout algorithm was used to calculate the position of radiation events and correct for pincushion distortion. The reconstructed image of the mouse heart phantom demonstrated reproducible image quality with submillimeter spatial resolution (0.7 mm), showing the feasibility of using the compact PSAPD-based gamma camera for a small animal SPECT system.     

Development of thermoelectric module based on dense Ca3Co4O9 and Zn0.98Al0.02O legs

Ca₃Co₄O₉ (p-type) and Zn_0.98Al_0.02O (n-type) pellets were prepared by conventional sintering (CS) and Spark Plasma sintering (SPS) starting from the oxides. The best p-type sample was SPS Ca₃Co₄O₉ obtained from pre-sintered pellets, with electrical conductivity σ = 144 S/cm and Seebeck coefficient S = 172 μV/K at 800 °C, while thermal conductivity κ = 2.00 W/m×K and figure of merit ZT = 0.23. The best n-type sample was CS Zn_0.98Al_0.02O showing σ = 83 S/cm and S = ?268 μV/K at 800 °C, while = 5.03 W/m×K and ZT = 0.127. The output power of a module based on SPS Ca₃Co₄O₉ and CS Zn_0.98Al_0.02O legs was 2.26 mW (with T = 500 °C, ΔT = 248 °C).     

Design of the shield tunnel for the trans-Tokyo bay highway

The Trans-Tokyo Bay Highway project is the first phase of an ambitious plan to connect Kawasaki and Chiba by a 15-km crossing of Tokyo Bay. The crossing involves a 5-km bridge, a 10-km undersea tunnel, and a manmade island in the middle of the bay. The construction method for the undersea tunnel must take into account the large external diameter of the primary lining (approx. 14 m); the extremely soft ground under the sea; the extremely high water pressure to which the tunnel will be subjected; and active seismic conditions in the Tokyo Bay area. This paper discusses the slurry shield tunnelling method adopted for the undersea tunnel portion of the project.