Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Untersuchungen zum Korrosionsverhalten von AlLi-Legierungen

Corrosion behaviour of aluminium-lithium alloys The AlLiMgCu alloy 8090 was studied in its texturated fine grained version “A” and in its recrystallized coarse grain structured version “C” in different artificially aged conditions in reference to several other AlLi alloys, each in its heat treatment condition of practical interest, and to the convetional alloy 2024 T3. The subject of research was the general corrosion behaviour of semifinished AlLi products, particularly sheet material, under alternate and permanent immersion conditions in neutral 3.5% sodium chloride solution; the stress corrosion behaviour was studied under constant load in the long transverse direction according to ASTM G44 and G49. The underaged conditions, which are the relevant conditions for technical application of the 8090 “A” and “C” sheets, showed an approximately equivalent or even better corrosion behaviour in comparison to the lithium-free alloy 2024 T3 in the corrosion tests with unloaded specimens. The threshold above which the AlLi alloy 8090 in some heat treatment conditions is attacked by stress corrosion cracking within the 30 days lasting constant load test depends on alloy composition, testing direction, grain size, stretch-forming, artificial ageing condition, surface pretreatment and the specimens' dimensions.     

Electrochemical Faceting of polycrystalline platinum in HF solutions

The electrochemical faceting of polycrystalline (pc) platinum yielding a (100)-preferred oriented electrode surface was accomplished in HF solutions by applying to the pc platinum electrode a square wave potential perturbation at 1 kHz in the 0.2 to 1.3 V range (vs rhe). SEM patterns of the resulting surfaces were also obtained. For HF concentrations up to 2 M no appreciable influence of the electrolyte concentration on the electrochemical faceting was noticed. Otherwise, the voltammetric response of the (100)-type preferred oriented platinum surface in the H-adatom potential range when compared to previously reported data resulted remarkably sensitive to the electrolyte composition. The discussion of results was based on the non-equilibrium adsorption conditions for anions under the periodic perturbation.     

Catalytic properties and electronic structure of copper ions in Cu-ZSM-5

The effect of ion exchange conditions, such as Si/Al ratio, precursor copper salt, pH and concentration of the solution, on the catalytic activity in SCR of NO by propane and on the electronic state of copper ions in Cu-ZSM-5 has been studied. The NO conversion in NO SCR by C₃H₈ has been found to reach a maximum value at Cu/Al ratio about 0.37–0.4 and remain constant at higher Cu/Al.

ESR and UV–vis DR spectroscopy have been used to elucidate stabilization conditions of copper ions in Cu-ZSM-5 zeolites as isolated Cu²⁺ ions, chain copper oxide structures and square-plain oxide clusters. The ability of copper ions for reduction and reoxidation in the chain structures may be responsible for the catalytic activity of Cu-ZSM-5. These transformations of copper ions are accompanied by the observation of intervalence transitions Cu²⁺–Cu⁺ and CTLM of the chain structures in the UV–vis spectra.     

Wetting behaviour of silicon nitride ceramics by Ti–Cu alloys

The wetting of Ti–Cu alloys on Si₃N₄ was analyzed by the sessile drop method, using an imaging system with a CCD camera during the heating under argon flow. The contact angle was measured as a function of temperature and time. The samples were cut transversally and characterized by scanning electron microscopy and energy dispersive spectrometry (SEM/EDS). Wettability of the Ti–Cu alloy on Si₃N₄ is influenced by the reaction between the Ti and the ceramic. The TC1 and TC2 alloys presented low final contact angle values around 2° and 26°, respectively, indicating good wetting on Si₃N₄.     

Grain growth kinetics in Dy-doped Bi0.5Na0.5TiO3 ceramics

Dysprosium-doped bismuth sodium titanate ceramics were prepared using the conventional mixed-oxide method. The amount of dysprosium used was varied from 0 to 2 at.%. The mixed powders were calcined at 800 °C and checked for phase purity using X-ray diffraction technique. The calcined powders were then cold-pressed into pellets and sintered at 1050 °C for the time ranging from 2 to 48 h. The ceramics were checked for phases and microstructures using an X-ray diffractometer and a scanning electron microscope, respectively. The analysis showed that undoped BNT ceramics sintered at longer time exhibited a significant grain growth with non-uniform grain size distribution and shape. The Dy-doped BNT however showed a much more limited grain growth behavior, resulting in smaller grain size and more equiaxed grain shape. It was also found that all Dy-doped BNT ceramics sintered at 48 h possessed lower porosity than those sintered for shorter time.     

Refractories for handling steel outside a furnace

A range of refractories is presented for handling steel outside a furnace, which are produced by the Borovichi Refractories Corporation. The refractory characteristics and working features are given. Translated from Novye Ogneupory, No. 9, pp. 29–35, September, 2008.     

Factors of large graphite crucible life

Production methods used to prepare graphite crucibles with high operating properties are considered: use as a filler of good graphitizing acicular coke, vibration molding of the original coke mix, use of production cycles for impregnation with medium temperature coal-tar pitch — firing, firing of compacted billets in metal containers, graphitization of fired billets in graphite cylinders. The last two production methods make it possible to reduce the temperature drop throughout the volume of a billet during heat treatment, and as a consequence to reduce crack development to a minimum as a result of reducing thermal stresses. All of the production methods recommended may be entirely accomplished in existing electrode plants and may be used to increase markedly the quality crucible graphite. It is possible to achieve a quality for these materials at the best world level. Translated from Novye Ogneupory, No. 8, pp. 28–33, August 2008.