Safety evaluation on the depressurization accident in the gas turbine high temperature reactor (GTHTR300)

Japan Atomic Energy Agency has been developing a gas turbine high temperature reactor (GTHTR300) with electric power of approximately 300 MW. One of the unique safety design concepts of this system is that events with frequency of occurrence of higher than 10⁻⁸/reactor-year are evaluated as design basis events in order to show that the frequency of large amount of FP release is less than 10⁻⁸/reactor-year. According to this concept, a depressurization accident by a large break of helium piping is postulated as a design basis event. This accident is one of the most serious accidents in the high-temperature gas-cooled reactors from the viewpoint of loss of coolability. The safety evaluation on the accident was conducted based on the actual design of the system. The short-term and long-term behaviors of fuel temperature after occurrence of the accident, internal pressure of the reactor building, oxidation behavior of fuels and graphite structures were evaluated and exposure dose of general public was also estimated using the results of evaluation of fuel temperature and fuel failure by oxidation. All of the evaluation results meet the safety criteria and feasibility of the GTHTR300 was shown by this study.     

Measurement of losses and saturated permeability of saturable coresunder submicrosecond saturation

Two specific methods are introduced for obtaining accurate losses and saturated permeability of saturable cores under submicrosecond saturation. One employs an additional inductor for accurate measurement of the losses. The other minimizes stray inductance for accurate measurement of the saturated permeability. The measured relative permeability of Co-based amorphous cores rapidly drops to nearly 1.0. On the other hand, ferrite cores need a much larger magnetic field than that for Co-based amorphous cores in order to obtain the relative permeability of 1.0     

Stress analysis of elastomeric materials at large extensions using the finite element method

The finite element method is applied to stress and strain analyses around rigid spherical particles in elastomers at large extensions. The stress and strain distribution computed agree well with the classical theoretical ones at small strain. At large extension, however, the maximum stress concentration factor increases greatly and the maximum strain concentration factor decreases slightly as strain increases. These tendencies are increased more in carbon black-filled elastomers than in unfilled ones, which can be understood reasonably by considering both the geometric and material non-linearity. Reinforcement of elastomers with rigid spherical particles was also analysed through a numerical computation. The computed results agree with the Guth and Mooney equations at low volume fraction of fillers. In carbon black-filled elastomers, on the other hand, where the modulus is much higher than that given by the above equations, the computations give a good agreement with the experiments, considering the 20% increase in effective diameter of the filler.     

Theory and characteristics of novel variable reluctance 1X resolver

Although brushless resolvers have been used widely as angular position transducers, they are expensive due to their intricate construction, involving a rotary transformer to supply the exciting coils wound on the rotor poles with the current. It is shown theoretically in this paper that the resolver without rotary transformer or brushes can be realized by simple construction, which consists of the stator core with both 4-poles exciting windings and 2-poles output ones and the rotor core carrying no windings. In this resolver the rotor core has minimum gap at one side and a maximum gap at another side of the diameter. It is characterized by an outer surface form that makes the fluctuation part of gap permeance very in proportion to cos θ, where θ represents the angular position of a point in the air gap with respect to the origin on the rotor, the point of minimum air gap. The method determining the rotor form to embody the aforementioned gap permeance variation is also shown. It has been confirmed not only by simulation but also experiment that the 2-phase output voltages of a model designed based on the theory have sinusoidal waveforms with very small harmonic contents. Moreover, the rotor position detected by processing the output voltages through the conventional resolver/digital converter was within acceptable engineering accuracy.     

Robust parameter-estimation using the bootstrap method for the2-parameter Weibull distribution

This paper proposes bootstrap robust estimation methods for the Weibull parameters; it applies bootstrap estimators of order statistics to the parametric estimation procedure. Estimates of the Weibull parameters are equivalent to the estimates using the extreme value distribution. Therefore, the bootstrap estimators of order statistics for the parameters of the extreme value distribution are examined. Accuracy and robustness for outliers are examined by Monte Carlo experiments which indicate adequate efficiency of the proposed reliability estimators for data with some outliers     

Transdermal Absorption of Zidovudine from Ethanol-Isopropyl Myristate Mixed System and Influence of Probenecid on It in Rats

Transdermal absorption of zidovudine (AZT) from an ethanol-isopropyl myristate (IPM) mixed system was examined in rats. For comparison of bioavailability (BA) after topical applications, 0.25 ml of the ethanol/IPM system containing 40% ethanol and 60 mM AZT was applied as a standard formulation. Values of the area under the plasma concentration-time curves of AZT for 8 hr (AUC_0-8), as indices of BA, following application of various formulations were compared with that of the standard formulation. Then the influence of content of the drug and ethanol, and application volume of the system was evaluated. BA was effectively improved only when the total amount of ethanol applied on the skin was increased. On the other hand, simultaneous transdermal application of AZT and probenecid increased the AU_0-8, of AZT without necessitating the increase in ethanol content in the formulation. In addition, coadministered probenecid improved cerebrospinal fluid/plasma concentration ratio of AZT.     

Sensitivity of an anadically oxidized aluminium film on a surface acoustic wave sensor to humidity

The sensitivity, transient response and sensitivity mechanism of a surface acoustic wave humidity sensor using porous anodically oxidized aluminium (alumina) films as mechanical interfaces have been studied theoretically and experimentally. It is found that the sensitivity of alumina films of 1.0 μm thickness is -0.034 m/(s %RH) and is the same order as that of polyimide films. The transient response of alumina films to humidity is about one order faster than that of polyimide films. For the sensitivity mechanism, the phase-velocity change is attributed to the mechanical perturbation caused by the absorption of water molecules. The equivalent density change of alumina films between 0 and 100%RH is about 0.7%. In addition, the actual stiffness constants of alumina films are two orders less than those of bulk alumina.     

Development of flexible organic light‐emitting diode on barrier film and roll‐to‐roll manufacturing

To come out with a successful organic light‐emitting diode (OLED) lighting business, it is very important to have clear differentiation of OLED from LEDs. Flexible OLED has merits, such as capability to be mounted on the curved wall, which is not easy for LEDs to achieve the feature. There are several approaches to make flexible OLEDs especially among those plastic barrier films that can bring high level of flexibility, which could not be achieved by any conventional lighting method. In this paper, barrier films with various water vapor transmission rate values, including 10^{? 6} order, are applied, and the conditions to have almost no dark spot growth under 85 °C and 85% high temperature/humidity test are shown. Flexible OLED panels are manufactured with the world's first roll‐to‐roll equipment using plastic barrier film.     

On-chip fabrication of magnetic alginate hydrogel microfibers by multilayered pneumatic microvalves

Alginate hydrogel has widespread applications in tissue engineering, cancer therapy, wound management and drug/cell/growth factor delivery due to its biocompatibility, hydrated environment and desirable viscoelastic properties. However, the lack of controllability is still an obstacle for utilizing it in the fabrication of 3D tissue constructs and accurate targeting in mass delivery. Here, we proposed a new method for achieving magnetic alginate hydrogel microfibers by dispersing magnetic nanoparticles in alginate solution and solidifying the magnetic alginate into hydrogel fiber inside microfluidic devices. The microfluidic devices have multilayered pneumatic microvalves with hemicylindrical channels to fully stop the fluids. In the experiments, the magnetic nanoparticles and the alginate solution were mixed and formed a uniform suspension. No aggregation of magnetic nanoparticles was found, which is crucial for flow control inside microfluidic devices. By regulating the flow rates of different solutions with the microvalves inside the microfluidic device, magnetic hydrogel fibers and nonmagnetic hydrogel fibers were fabricated with controlled sizes. The proposed method for fabricating magnetic hydrogel fiber holds great potential for engineering 3D tissue constructs with complex architectures and active drug release.