Intensely irradiated steel components: Plastic and fracture properties, and a new concept of structural design criteria for assuring the structural integrity

In order to develop a systematic and reasonable concept assuring the structural integrity of components under intense neutron irradiation, two basic tensile properties, true stress-true strain (TS-TS) curves and fracture strain, were investigated on an austenitic stainless steel and martensitic steel. Application of Swift equation is confirmed to a large plastic strain range of TS-TS curves. Fracture strain ?_f data were well correlated as ?_f + ?₀ = const. where ?₀ is the pre-strain representing the irradiation hardening.Based on those formulations and available experimental information, several critical issues to be dealt with in developing the concept were identified possible reduction in ductility, significant change in mechanical properties, remarkable cyclic softening and other unique cyclic properties observed during a high-cycle fatigue testing, and the redundancy of the plastic collapse concept to bending. Existing structural codes are all based on the assumption that there will be no significant changes in mechanical properties during operation, and of high ductility. Therefore, a new concept for assuring structural integrity is required for application not only to components with high ductility but also components with reduced ductility. First, potential failure modes were identified, and a new and systematic concept was proposed for preventing these modes of failure, introducing a new concept of categorizing the loadings by stability of deformation process to fracture (as type F and M loadings). Based on the basic concept, a detailed concept of how to protect against ductile fracture was given, and loading type-dependent limiting parameters were set.Finally, application of the detailed concept was presented, especially on determination of loading type (in numerical approach, the formulation of TS-TS curves and fracture strain derived above are needed), and on how to determine the limiting parameters as allowable limits. Experiments were done to identify the loading type of a tensile loading acting on a structure with a discontinuity. Tensile loadings acting on an intensely neutron-irradiated flat plate with a hole in the center cause plastic tensile instability and necking at the minimum ligament section but do not initiate any surface crack at the initiation of necking.     

R&D activities on manufacturing plasma-facing unit for prototype of ITER divertor outer target in JADA

Japan Domestic Agency (JADA) carried out R&Ds activities to improve joining CFC monoblocks onto a CuCrZr cooling tube in PFUs to boost the success rate of joint and to confirm load carrying capability of the monoblock attachments to Steel Support Structure (SSS) against tensile force simulating electromagnetic load to pull PFUs from SSS. In joining the CFC monoblocks to the cooling tube, JADA has adopted brazing by using noble-metal-free filler with the following improvements; (1) metalizing joint surface of CFC using Ti-coating with accurate thickness controlling, (2) Changing buffer layer material from soft pure copper to Cu–W alloy. By using the present improved joint, JADA has manufactured three mock-ups with 5 CFC monoblocks and tested against repetitive high heat loads more than 20 MW/m². All of CFC monoblocks of each mockup can survive the high heat loads throughout 1000 cycles with no degradation of heat removal capability. Regarding the load carrying capability of monoblock attachments to SSS, tensile experiments were carried out using the same geometries of CFC and tungsten monoblocks in PFUs and the results show that both geometries and joints meet the ITER requirements, that is, 3 kN and 8 kN, respectively.     

Development of the Water Cooled Ceramic Breeder Test Blanket Module in Japan

The development of a Water Cooled Ceramic Breeder (WCCB) Test Blanket Module (TBM) is being performed as one of the most important steps toward DEMO blanket in Japan. For the TBM testing and evaluation toward DEMO blanket, the module fabrication technology development by a candidate structural material, reduced activation martensitic/ferritic steel, F82H, is one of the most critical items from the viewpoint of realization of TBM testing in ITER. In Japan, fabrication of a real scale first wall, side walls, a breeder pebble bed box and assembling of the first wall and side walls have succeeded. Recently, the real scale partial mockup of the back wall was fabricated. The fabrication procedure of the back wall, whose thickness is up to 90 mm, was confirmed toward the fabrication of the real scale back wall by F82H. Important key technologies are almost clarified for the fabrication of the real scale TBM module mockup. From the view point of testing and evaluation, development of the technology of the blanket tritium recovery, development of advanced breeder and multiplier pebbles and the development of the blanket neutronics measurement technology are also performed. Also, tritium production and recovery test using D-T neutron in the Fusion Neutronics Source (FNS) facility has been started as the verification test of tritium production performance. This paper overviews the recent achievements of the development of the WCCB TBM in Japan.     

Fabrication of Flexible and Transparent Conductive Nanosheets by the UV‐Irradiation of Gold Nanoparticle Monolayers

Conductive films that are highly transparent and flexible are extremely attractive for emerging optoelectronic applications. Currently, indium‐doped tin oxide films are the most widely used transparent conductive films and much research effort is devoted to developing alternative transparent conductive materials to overcome their drawbacks. In this work, a novel and facile approach for fabricating transparent conductive Au nanosheets from Au nanoparticles (AuNPs) is proposed. Irradiating an AuNP monolayer at the air–water interface with UV light results in a nanosheet with ≈3.5 nm thickness and ≈80% transparency in the UV–visible region. Further, the so‐fabricated nanosheets are highly flexible and can maintain their electrical conductivity even when they are bent to a radius of curvature of 0.6 mm. Fourier‐transform infrared and X‐ray photoelectron spectroscopy characterizations reveal that the transformation of the monolayer of AuNPs into the nanosheet is induced by the photodecomposition and/or photodetachment of the dodecanethiol ligands capping the AuNPs. Further, the UV‐irradiation of a hybrid monolayer consisting of AuNPs and silica particles affords the patterning of Au nanosheets with periodic hole arrays.     

Redox‐Active Polymers Connecting Living Microbial Cells to an Extracellular Electrical Circuit

Microbial electrochemical systems in which metabolic electrons in living microbes have been extracted to or injected from an extracellular electrical circuit have attracted considerable attention as environmentally‐friendly energy conversion systems. Since general microbes cannot exchange electrons with extracellular solids, electron mediators are needed to connect living cells to an extracellular electrode. Although hydrophobic small molecules that can penetrate cell membranes are commonly used as electron mediators, they cannot be dissolved at high concentrations in aqueous media. The use of hydrophobic mediators in combination with small hydrophilic redox molecules can substantially increase the efficiency of the extracellular electron transfer process, but this method has side effects, in some cases, such as cytotoxicity and environmental pollution. In this Review, recently‐developed redox‐active polymers are highlighted as a new type of electron mediator that has less cytotoxicity than many conventional electron mediators. Owing to the design flexibility of polymer structures, important parameters that affect electron transport properties, such as redox potential, the balance of hydrophobicity and hydrophilicity, and electron conductivity, can be systematically regulated.     

Label-free protein biosensor based on aptamer-modified carbon nanotube field-effect transistors

We have fabricated label-free protein biosensors based on aptamer-modified carbon nanotube field-effect transistors (CNT-FETs) for the detection of immunoglobulin E (IgE). After the covalent immobilization of 5'-amino-modified 45-mer aptamers on the CNT channels, the electrical properties of the CNT-FETs were monitored in real time. The introduction of target IgE at various concentrations caused a sharp decrease in the source-drain current, and a gradual saturation was observed at lower concentrations. The amount of the net source-drain current before and after IgE introduction on the aptamer-modified CNT-FETs increased as a function of IgE concentration. The detection limit for IgE was determined as 250 pM. We have also prepared CNT-FET biosensors using a monoclonal antibody against IgE (IgE-mAb). The electrical properties of the aptamer- and antibody-modified CNT-FETs were compared. The performance of aptamer-modified CNT-FETs provided better results than the ones obtained using IgE-mAb-modified CNT-FETs under similar conditions. Thus, we suggest that the aptamer-modified CNT-FETs are promising candidates for the development of label-free protein biosensors.     

Characteristics of an Experimental Guided Millimeter-Wave Transmission System

An experimental guided millimeter-wave transmission system is constructed employing two 806-Mbit/s digital repeaters, an 8.4-km waveguide line loop, and channel coupling networks. This paper presents its characteristics, such as waveforms, amplitude and delay, error rate, and timing jitter in some detail.     

Some elements comprising particulate matter during summer in waters of various environments in British Columbia, Canada

Multi-elemental traces comprising particulate matter in natural water collected during summer in 1978 and 1979 from British Columbia, Canada, were analyzed by α-particle excited X-ray fluorometry. Common elements from all waters examined were Si, Cl, Ca and Fe. The similarity of their distribution in different aquatic environments was statistically analyzed. They were distributed homogeneously in the marine environment but heterogeneously in the freshwater environments. No heavy metals concerned with the environmental standards were detected for all waters examined.     

Theory and characteristics of novel variable reluctance 1X resolver

Although brushless resolvers have been used widely as angular position transducers, they are expensive due to their intricate construction, involving a rotary transformer to supply the exciting coils wound on the rotor poles with the current. It is shown theoretically in this paper that the resolver without rotary transformer or brushes can be realized by simple construction, which consists of the stator core with both 4-poles exciting windings and 2-poles output ones and the rotor core carrying no windings. In this resolver the rotor core has minimum gap at one side and a maximum gap at another side of the diameter. It is characterized by an outer surface form that makes the fluctuation part of gap permeance very in proportion to cos θ, where θ represents the angular position of a point in the air gap with respect to the origin on the rotor, the point of minimum air gap. The method determining the rotor form to embody the aforementioned gap permeance variation is also shown. It has been confirmed not only by simulation but also experiment that the 2-phase output voltages of a model designed based on the theory have sinusoidal waveforms with very small harmonic contents. Moreover, the rotor position detected by processing the output voltages through the conventional resolver/digital converter was within acceptable engineering accuracy.