Enrichment of arachidonic acid: Selective hydrolysis of a single-cell oil fromMortierella withCandida cylindracea lipase

Three lipases, isolated previously in our laboratory, and a known lipase fromCandida cylindracea were screened for the enrichment of arachidonic acid (AA). The enzyme fromC. cylindracea was the most effective for the production of oil with high concentration of AA. When a single-cell oil fromMortierella alpina, containing 25% AA, was hydrolyzed with this lipase for 16 h at 35°C, the resulting glycerides contained 50% AA at 52% hydrolysis. After this, no further hydrolysis occurred, even with additional lipase. However, when the glycerides were extracted from the hydrolyzate and were hydrolyzed again with new lipase, the resulting oil contained 60% AA, with a recovery of 75% of its initial AA content. Triglycerides were the main components of the resulting oil. The release of each fatty acid from the oil depended on the hydrolysis rate of its ester. The fatty acid, whose ester is the poorest substrate for the enzyme, is concentrated in the glycerides.     

Temperature and frequency dependence of dielectric loss of Ba(Mg1/3Ta2/3)O3 microwave ceramics

Ba(Mg_1/3Ta_2/3)O₃ ceramic possessing extremely high Q × f value of more than 300 THz at microwave frequency was developed in our previous study. It is of great interest to understand the mechanism of microwave absorption in such a practical material. In the present study we report on the temperature dependence of the dielectric loss in the Ba(Mg_1/3Ta_2/3)O₃. The mechanism of the microwave absorption is discussed using two phonons difference process. The samples were prepared by conventional solid state reaction and sintered at 1893 K in oxygen atmosphere. Dielectric properties in the microwave range were measured by Hakki & Colemann and resonant cavity methods in the temperature range of 20–300 K. Whispering gallery mode technique was used for the measurement of the dielectric properties at the millimeter wave frequency. Dielectric loss of the Ba(Mg_1/3Ta_2/3)O₃ at the microwave frequency increases with temperature between 200 and 300 K in general agreement with the theory of intrinsic dielectric loss derived from the two phonon difference process. However below 200 K, the dielectric loss has shown a distinctive behavior with a loss peak at 40 K. It was inferred that the loss peak of the Ba(Mg_1/3Ta_2/3)O₃ was caused by the local orientation polarization having dispersion at the microwave frequency.     

Gelation of poly(vinyl alcohol)/phenol/water solutions and gel spinning

The light transmittance of the gels of poly(vinyl alcohol) (PVA)/phenol/water solutions was examined for the entire range of phenol/water content. Excellent transparency was found for the gels with phenol contents of 70–95 vol %. In full consideration of the results for the transparency and melting temperature of the gels and the viscosity and gelation ability of solutions, the PVA solutions of 75 vol % phenol content were selected for the gel spinning. The maximum dynamic moduli of drawn filaments at 25°C (room temperature) were 42 GPa (15x) for atactic PVA and 45 GPa (14x) for syndiotacticity-rich PVA. © 1995 John Wiley & Sons, Inc.     

HEXHOOP: Modular Templates for Converting a Hex-Dominant Mesh to an ALL-Hex Mesh

This paper presents a new mesh conversion template called HEXHOOP, which fully automates a con-version from a hex-dominant mesh to an all-hex mesh. A HEXHOOP template subdivides a hex/prism/pyramid element into a set of smaller hex elements while main-taining the topological conformity with neighboring elements. A HEXHOOP template is constructed by assembling sub-templates, cores and caps. A dicing template for a hex and a prism is constructed by choosing the appropriate combination of a core and caps. A template that dices a pyramid without losing conformity to the adjacent element is derived from a HEXHOOP template. Some experimental results show that the HEXHOOP templates successfully convert a hex-dominant mesh into an all-hex mesh. ID="A1" Correspondence and offprint requests to: K. Shimada, Department of Mechanical Engineering, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA 15213–3890, USA. E-mail: shimada@cmu.edu     

Preparation and phase transition of Gd4(Al1 − xGax)2O9 solid solutions

The solid-solution compounds of Gd₄(Al_{1 – x} Ga _x )₂O₉ (x = 0.0–1.0) were prepared at 1600°C for 5 h in air. The unit cell volume of the compounds increased from 0.853 to 0.878 nm³ with x. Phase transitions having a temperature hysteresis were observed from 1100° to 1400°C by calorimetry and dilatometry. The transition temperature increased with x. The volume of the high-temperature phase was 0.5% smaller than that of the low-temperature phase at the transition temperature. The volume changes were independent of x. The hysteresis width observed by the dilatometry was about 300°C for the Gd₄Al₂O₉ ceramics (grain size: about 1 m) and decreased to 50°C for the Gd₄(Al_0.2Ga_0.8)₂O₉ ceramics (grain size: over 10 m). Gd₄Ga₂O₉ was unstable at low temperature and decomposed to Gd₃GaO₆ and Gd₃Ga₅O₁₂ during the thermal analyses.     

InGaAs angled-grating distributed Bragg reflector lasers integrated with grating outcoupler for collimation

An angled-grating distributed Bragg reflector (DBR) laser integrated with a grating outcoupler (GO) is proposed and demonstrated. It consists of an angled broad-area gain stripe surrounded by angled DBR (/spl alpha/-DBR) gratings parallel to the gain stripe and two DBR gratings for feedback at the stripe ends, and a GO for emitting a collimated output beam. Due to distributed Bragg reflection in the /spl alpha/-DBR gratings, filamentation can be suppressed. Single-mode lasing up to 69 mW peak power was obtained under pulse condition. A collimated output beam with divergence angles, close to the diffraction limit, was obtained. These results confirm the effectiveness of the /spl alpha/-DBR gratings.