Engineering Computation and Analysis of Enhancing Efficiency for Folded Waveguide TWT in MMW

Large signal operating equations in TWT have been solved by numerical solve method. The relations between interaction efficiency and design parameters in TWT are analyzed. A fast engineering design method of enhancing efficiency for folded waveguide TWT by velocity resynchronization is described. The computation is shown that the efficiency of Ka-band folded waveguide TWT with double taper can be enhanced over twice as original tube. This method of approach is very useful for tube designer.     

Associative properties of perfluorooctyl end‐functionalized polystyrene–poly(ethylene oxide) diblock copolymers

The synthesis of 2,2,3,3‐tetrahydro‐perfluoroundecanoyl end‐functionalized polystyrene–poly(ethylene oxide) block (PS‐block‐PEO‐R_F) copolymers and their matching PS‐block‐PEO diblock copolymers was carried out by sequential anionic polymerization. Viscometry and ¹⁹F NMR studies show that the PS‐block‐PEO copolymers, in contrast to their matching PS‐block‐PEO‐R_F copolymers, exhibit a micellar rather than the associative behavior seen for the latter. However, the presence of an excess of fluorinated acid, used for end‐functionalization, produces a reduction of the associative behavior above the overlap concentration, with the fluorinated acid acting like a surfactant. A competition may also occur between PS—and R_F—mediated micellization. Copyright © 2004 Society of Chemical Industry     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

钻机绞车滚筒体的窄间隙埋弧焊

针对钻机绞车滚筒体采用手工电弧焊工人劳动强度大、焊接效率低、质量不稳定及返修率高等问题,研制了钻机绞车滚筒体窄间隙埋弧焊专机。该专机由ESAB—A2埋弧焊电源和焊接小车、窄间隙焊头、滚轮架、防窜装置、旋转地线夹、三维焊接工作台、焊剂自动回收机组成。使用表明,采用该焊机焊接的滚筒体焊缝质量完全符合设计要求,合格率100%,焊接效率比原来提高6倍。每件滚筒体的焊接可降低人工成本约80%。     

Bias dependence of high-frequency noise in heterojunction bipolar transistors

Hawkins' isothermal model developed to study noise in bipolar junction transistors (BJTs) is modified to investigate bias-dependent noise in heterojunction bipolar transistors (HBTs) by incorporating thermal effects. It is shown that the inclusion of thermal effects into the high-frequency noise model of HBTs is necessary as the temperature of the device may become very different from the ambient temperature, especially at high bias current. Calculation of the noise figure by including the thermal effect shows that the isothermal calculation may underestimate the noise figure at high bias current. It is observed that noise at low bias is ideality factor n dependent whereas high bias noise is insensitive to the variation of n. Moreover, the common base current gain plays a major role in the calculation of the minimum noise figure. The excellent fit obtained between the theoretical calculation and the measured data are attributed to the inclusion of the bias-dependent junction heating as well as C/sub De/ and C/sub bc/ into the present calculation.     

A Bluetooth Routing Protocol Using Evolving Fuzzy Neural Networks

In this paper, a routing protocol which utilizes the characteristics of Bluetooth technology is proposed for Bluetooth-based mobile ad hoc networks. The routing tables are maintained in the master devices and the routing zone radius for each table is adjusted dynamically by using evolving fuzzy neural networks. Observing there exists some useless routing packets which are helpless to build the routing path and increase the network loads in the existing ad hoc routing protocols, we selectively use multiple unicasts or one broadcast when the destination device is out of the routing zone radius coverage of the routing table. The simulation results show that the dynamic adjustment of the routing table size in each master device results in much less reply time of routing request, fewer request packets and useless packets compared with two representative protocols, Zone Routing Protocol and Dynamic Source Routing.     

无线光接入技术

无线光通信系统以其高带宽、低成本和安装迅捷等优势成为非常有竞争力的光接入新技术。对无线光通信系统的关键技术、主要优势和存在的问题及国内外相关产品的发展状况和主要特点进行了论述和介绍。     

基于本地缓存的弹性分组环保护机制

本文提出一种基于本地缓存的弹性分组环保护倒换机制(WrapProtectionBasedOnLocalBuffers,简称WP-LB)。其主要思想是当环路上任何位于源节点和故障区域之间的中间节点接收到含有故障信息的控制信令后,就不再向下游转发数据分组,而是在本地缓存这些数据。等到保护通路建立好之后,再把缓存的数据分组经过保护通路发送给目的节点。分析计算表明,与原有的保护倒换(WrapProtection,简称WP)机制相比,WP-LB机制不仅提高带宽利用率,减少平均时延,并且还能避免数据包的丢失和失序。     

TPS/TDC3000系统串口通讯的规划与应用

针对TPS/TDC30 0 0系统串口通讯方式、机理进行了一般性的介绍 ,对规划与应用中常见的的问题 ,根据实际工程应用经验提出了解决方案。     

Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.