Restoration of solid oxide fuel cell stacks after failure of partial cells

We investigated a solid oxide fuel cell stack that employs anode-supported planar cells in which two intermediate plates are installed every 10 cells to determine the influence of the separation and reconnection of the intermediate plates after high temperature operation. We showed that this separation and reconnection caused no significant degradation in stack performance. A 30-cell stack, which was constructed by removing two 10-cell sub-stacks from a 50-cell stack that had operated stably 1200 h, functioned well. The difference between the average voltages of the cells in the 50- and 30-cell stacks was less than 3% when the current density, fuel utilization, and oxygen utilization were 0.30 A cm⁻², 60%, and 15%, respectively. The 30-cell stack operated stably for about 1200 h with almost no degradation. These findings indicate that our stack can be restored after cells in the stack have broken down simply by removing the 10-cell sub-stacks that contain the broken cells and replacing them with undamaged 10-cell sub-stacks.     

Influence of heating and laser irradiation on the Raman D band in single-wall carbon nanotubes

Fine structure of the Raman D band in single-wall carbon nanotubes (SWNTs) was investigated by heating and laser irradiation. It is shown that the D band is composed of three components at ～ 1313, 1340, and 1355 cm^? 1, denoted by D₁, D₂, and D₃, respectively. The D₁ and D₂ intensities significantly increase with laser irradiation in air and vacuum, respectively. The D₃ intensity drastically increases with heating in air. From these results, it is suggested that the fine structure of the D band is attributed to different kinds of defects introduced in SWNTs.     

Numerical simulation of solidification for aluminum-base multicomponent alloy

Solidification simulation of an aluminum-base multicomponent alloy was carried out by a method combining thermodynamic analysis using Thermo-Calc and heat-transfer calculation. An Al-9.5% Si-3% Cu-1% Mg-0.8% Fe (all mass%) aluminum-base multicomponent alloy was used for the simulation. The effect of latent heat on the heat-transfer calculation was considered by using an enthalpy method. The temperature-enthalpy curves for both an equilibrium state and nonequilibrium state with assumptions of no diffusion in the solid were calculated by using Thermo-Calc. A small casting with a cylindrical shape was used for the heat-transfer simulation. The vertical cross section of the casting was divided into rectangular grids, and the enthalpy change of each grid was numerically calculated. The calculated enthalpies in the grids were converted for each time-step into temperatures by using the temperature-enthalpy curve. A casting experiment was carried out under the same conditions as those of the simulation, and the calculated cooling curves obtained under the nonequilibrium condition agreed with the experimental ones.     

Influence of γ Irradiation on the Mechanical Strength and In Vitro Biodegradation of Porous Hydroxyapatite/Collagen Composite

Gamma irradiation treatment (GIT) is the most widely used sterilization method for biomaterials in spite of the potential to degrade polymers. The adverse effects of GIT on the mechanical properties and biological stabilities of porous hydroxyapatite/collagen (HAp/Col) composites were investigated in this study. Those properties of a porous HAp/Col composite stabilized by dehydrothermal treatment (DHT) drastically decreased by GIT in the same manner as conventional pure Col materials. DHT after GIT could partially eliminate the adverse effects, due to the introduction of cross-linkage among the degraded Col molecules.     

Morphologic analysis of odontogenic cysts with computed tomography

PURPOSE: The purpose of this study was to analyze the effects of lesion site and epithelial keratinization on the morphologic characteristics of odontogenic cysts and clarify determinate factors for cyst morphology. MATERIAL AND METHODS: Computed tomographic images of 92 odontogenic cysts were analyzed: 31 primordial, 31 dentigerous and 30 radicular. Thirty-four cysts were located in the maxilla (6 primordial, 10 dentigerous, and 18 radicular) and 58 in the mandible (25 primordial, 21 dentigerous, and 12 radicular). Histologically, 31 cysts showed epithelial keratinization (18 primordial and 13 dentigerous). No keratinization was seen in radicular cysts. The morphologic features of cysts were assessed by measuring long length parallel to dental arch and short length vertical to it and calculating the long/short ratio. In addition, the computed tomography pattern of the cyst was classified into unilocular, lobulated, and multilocular patterns. Appearance of the sclerotic rim and surrounding cortex were classified into three and four patterns respectively to evaluate the developmental features of the cyst. RESULTS: As a whole, the long length of the primordial cysts was statistically larger than the other two cyst groups and resulted in a larger long/short ratio. Statistical differences of CT pattern were also seen among cyst groups. There was no preference in any cyst group for the appearance of the sclerotic rim and cortex. There were statistical differences between maxilla and mandible in short axis and long/short ratio. The maxillary cysts generally showed round shapes irrespective of their histologic characteristics. A multilocular pattern was more frequent in the keratinized group of mandibular primordial cysts. In dentigerous cysts, a multilocular pattern was seen only in the keratinized group and the long/short ratio was statistically larger; cyst shape was elliptical along the long axis. CONCLUSION: Our results demonstrated morphologic differences of odontogenic cysts caused by lesion site and keratinization. The dentigerous cyst with predominant keratinization should be included in the primordial cyst (odontogenic keratocyst) group.     

Chemical sensing by an electrical oscillator: Detection and quantification of cationic surfactants

A new chemical sensing system using an electrical oscillator has been developed. This sensing system measures the electrical ‘non-linearity’ at the surface of an electrode immersed in a test solution: a sinusoidal voltage is applied to the electrode and the higher harmonics of the output current are obtained by Fourier transformation. This sensing system has been used to detect and quantify surfactant molecules in solutions. The relative intensity P₂/P₁ of the peaks of the second (P₂) and first (P₁) harmonics in the output current was found to be linearly correlated with the logarithms of the concentrations of cationic surfactants such as cetylpyridium bromide (CPB) and cetyl-N,N,N-trimethylammonium bromide (CTAB), but not with those of the anionic surfactant sodium dodecyl sulfate (SDS) or the neutral surfactant Triton X-100. The reproducibility of this sensing system was shown to be excellent.     

Premixed edge flame in a counterflow field with a stretch rate gradient

An edge flame was established in a counterflow field with a stretch rate gradient using twin rectangular burners which were misaligned by a few degrees. The stretch rate gradient was quantitatively defined as a function of the angle between the two burners and the distance from the edge of the burner, and thus the effect of stretch rate gradient on the behavior of the edge flame was investigated. The local chemical reaction rate at the edge of a CH₄/air flame was stronger than that at other parts of the flame. On the other hand, the reaction rate at the edge of a C₃H₈/air flame was weaker than that of other parts of the flame. The curvature of the flame edge of the CH₄/air flame was much larger than that of the C₃H₈/air flame. These results are thought to be due to the effect of the Lewis number. The ratios of the local stretch rate at the flame edge to the extinction stretch rate for planar twin flames with the same composition as the edge flame were 0.5 to 0.7 for the CH₄/air flame and 0.6 to 0.8 for the C₃H₈/air flame. These values were midway between those in the numerical simulation by Daou and Linan and those in the experiment by Liu and Ronney. Moreover, it was shown that an increase in the stretch rate gradient resulted in a lower local stretch rate at the flame edge. Behavior of the edge flames did not depend on the Lewis number of the mixture.     

Linear programming software tools on UNIX System

Linear programming(LP) is one of the most widely used Operations Research/Management Science/Industrial Engineering techniques. Recently, multiple criteria decision making or multiple objective linear programming has been well established as a practical approach to seeking satisfactory solutions to real-world decision problems.

In this paper we develop software tools for solving various linear programming problems such as a traditional LP problem, bicriteria LP problem, and multi-criteria LP problem on UNIX system. In a phase for reading data of various LP problems, we define a BNF(Backus-Nauel form) of various LP problems and implement BNF rules by using the C programming language.

In a phase for computing various LP problems, we use efficient methods for solving LP problems, develop various software tools on UNIX system, and combine each LP tool corresponding to an user request in which the Shell programming is used.

We also demonstrate some real-world LP problems by using LP software tools developed here on an UNIX System. Sanyo MPS 020.     

Structure and orientation development in biaxial stretching of ultrahigh molecular weight polyethylene gel films

Ultrahigh molecular weight polyethylene (UHMWPE) gel films were prepared by gelation crystallization from decalin solutions. According to wide- and small-angle X-ray scattering (WAXD and SAXS) studies, single crystal mat texture with crystal c-axis oriented normal to film surface generally develops. However, randomly oriented structure can also develop if an external force is applied to gel films during gelation crystallization. Both textures invariably yield high drawability in uniaxial mode with outstanding modulus and strength. Biaxial films, typically 5 × 5, 6 × 6, 8 × 8, and 10 × 10 times the original dimensions, were prepared at 130°C–135°C in a biaxial stretcher. Optical microscopic Investigations reveal the development of interwoven fibrillar structure in all specimens. WAXD and SAXS studies show that lamellar structure transforms to fibrillar texture during biaxial stretching. Crystal orientation is characterized by WAXD pole figure and infrared dichroic methods. Mechanical studies suggest that tensile modulus and strength appear uniform. In comparison with uniaxial deformation, significant improvement in the lateral strength is seen in the biaxially stretched films.