Crystallite size distribution and the lattice distortions in highly γ-irradiated linear polyethylene

Crystallite size distributions and lattice distortions have been analysed for highly-irradiated linear polyethylene in the direction normal to 1 1 0 and 0 0 1 lattice planes through X-ray line profile analysis. It has been found that the lateral crystallite size is little affected irradiation greater than 1000 Mrad, whereas that in the chain direction decreases almost linearly with the dose of irradiation. A minor difference in the crystallite size between irradiation atmospheres, i.e. irradiation in air or in vacuum, has been disclosed at a very high dose of irradiation. The above degradation behaviour of crystallites and the change in lattice distortions have proved that radiation cross-links are mainly formed in the amorphous region near the lamellar surface of polyethylene.     

Voltage Control of Static Var Compensator for a Remote System Interconnected by Long‐Distance AC Cables

The voltage variation in a remote system is large when the system is connected by long‐distance AC cables due to the cable capacitance. In Japan, the longest 54‐km 66‐kV AC submarine cable interconnection between the Kyushu mainland and Goto Islands was commissioned in 2005. It was requested to mitigate the voltage variation caused by switching off and on one circuit of the two circuits in the AC cables when a fault occurs. Since the conventional voltage control methods such as transformer tap changer or shunt capacitor and reactor banks are not sufficient because of their slow response time, a static var compensator (SVC) was installed on the Goto Islands. In such an application, an SVC control method should be developed so as not to override the existing voltage control systems. This paper describes the SVC control method developed for the Goto Islands AC interconnection project, which can be applied to similar situations. The effectiveness of the control method was verified by the results of effective value simulation and of field testing, which was implemented before the SVC was commissioned in 2007. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(3): 19–30, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22337     

A consistent grayscale‐free topology optimization method using the level‐set method and zero‐level boundary tracking mesh

This paper proposes a level‐set based topology optimization method incorporating a boundary tracking mesh generating method and nonlinear programming. Because the boundary tracking mesh is always conformed to the structural boundary, good approximation to the boundary is maintained during optimization; therefore, structural design problems are solved completely without grayscale material. Previously, we introduced the boundary tracking mesh generating method into level‐set based topology optimization and updated the design variables by solving the level‐set equation. In order to adapt our previous method to general structural optimization frameworks, the incorporation of the method with nonlinear programming is investigated in this paper. To successfully incorporate nonlinear programming, the optimization problem is regularized using a double‐well potential. Furthermore, the sensitivities with respect to the design variables are strictly derived to maintain consistency in mathematical programming. We expect the investigation to open up a new class of grayscale‐free topology optimization. The usefulness of the proposed method is demonstrated using several numerical examples targeting two‐dimensional compliant mechanism and metallic waveguide design problems. Copyright © 2014 John Wiley & Sons, Ltd.     

Surface-collection efficiency of Nuclepore filters for nanoparticles

The flat surface of Nuclepore filters is suitable for observing collected particles with a scanning electron microscope (SEM). However, experimental data on surface-collection efficiency are limited because surface-collection efficiencies cannot be measured directly using aerosol measuring instruments. In this study, the surface-collection efficiencies of Nuclepore filters were determined by establishing the ratio of the number of particles deposited on the surface of the filter visually counted with an SEM to the number of inflow particles counted by a condensation particle counter, using monodispersed polystyrene latex particles (30–800 nm) and silver particles (15–30 nm). Because Nuclepore filters with smaller pore sizes would be expected to produce higher minimum surface-collection efficiency and a higher pressure-drop, 0.08 and 0.2 µm Nuclepore filters were chosen as the test filters in view of both collection efficiency and pressure drop. The results showed that the minimum surface-collection efficiencies of the 0.08 µm pores at face velocities of 1.9 and 8.4 cm·s^?1 were approximately 0.6 and 0.7, respectively, and those of the 0.2 µm pores at face velocities of 1.5 and 8.6 cm·s^?1 were approximately 0.8 and 0.6, respectively. Because the pressure drop of the 0.2 µm pore filter was lower than that of the 0.08 µm pore filter under the same flow-rate conditions, the 0.2 µm pore filter would be more suitable considering the pressure drop and collection efficiency. The obtained surface collection efficiencies were quantitatively inconsistent with theoretical surface-collection efficiencies calculated using conventional theoretical models developed to determine the collection efficiency of filters with larger pores.

© 2016 American Association for Aerosol Research     

Aerosol Particle Collection Efficiency of Holey Carbon Film-Coated TEM Grids

A simple sampling method to collect aerosol particles for transmission electron microscope (TEM) analysis was developed by R’mili and others in 2013. The method involves passing air through a holey carbon film-coated copper mesh TEM grid (holey carbon grid) and sampling particles by filtration. In this study, we proposed a modified calculation method to represent the collection efficiencies of holey carbon grids, taking into consideration the porosity of the copper mesh. We then evaluated the particle collection efficiencies of holey carbon grids both theoretically and experimentally. We tested the collection efficiency of two types of holey carbon grids, with nominal pore sizes of 1.2 and 0.6 μm, using particles of monodispersed polystyrene latex (PSL) and potassium chloride. The overall collection efficiency of each grid (E_grid) was determined by the downstream/upstream concentration ratio measured by condensation particle counters (CPCs). In addition, for PSL particles, the collection efficiency of the holey carbon film (E_film) was determined by the ratio of the number of particles on the film (counted on a scanning electron microscope) to the number of inflow particles (counted by a CPC). We compared model calculations against the experimental results obtained in this study and those reported by R’mili and others in 2013. These data showed that the calculated E_grid values were in reasonably good agreement with the experimental E_grid values. However, although the model calculation indicated that E_film ≈ E_grid, there was an inconsistency between the experimental E_film and E_grid, which requires further investigation in order to determine its cause.

Copyright 2014 American Association for Aerosol Research     

Morphology‐dependent electrocatalytic activity of nanostructured Pt/C particles from hybrid aerosol–colloid process

An optimum nanostructure and pore size of catalyst supports is very important in achieving high catalytic performances. In this instance, we evaluated the effects of various carbon nanostructures on the catalytic performances of carbon‐supported platinum (Pt/C) electrocatalysts experimentally and numerically. The Pt/C catalysts were prepared using a hybrid method involving the preparation of dense, hollow, and porous nanostructured carbon particle via aerosol spray pyrolysis followed by microwave‐assisted Pt deposition. Electrochemical characterization of the catalysts showed that the porous Pt/C catalyst gave the best performance; its electrochemical surface area was much higher, more than twice than those of hollow or dense Pt/C. The effects of pore size on electrocatalysis were also studied. The results showed the importance of a balance between mesopores and macropores for effective catalysis with a high charge transfer rate. A fluid flow model showed that good oxygen transport contributed to the catalytic activity. © 2015 American Institute of Chemical Engineers AIChE J, 62: 440–450, 2016     

A GIS-based DRASTIC model for assessing aquifer vulnerability in Kakamigahara Heights, Gifu Prefecture, central Japan

Vulnerability assessment to delineate areas that are more susceptible to contamination from anthropogenic sources has become an important element for sensible resource management and land use planning. This contribution aims at estimating aquifer vulnerability by applying the DRASTIC model as well as utilizing sensitivity analyses to evaluate the relative importance of the model parameters for aquifer vulnerability in Kakamigahara Heights, Gifu Prefecture central Japan. An additional objective is to demonstrate the combined use of the DRASTIC and geographical information system (GIS) as an effective method for groundwater pollution risk assessment. The DRASTIC model uses seven environmental parameters (Depth to water, net Recharge, Aquifer media, Soil media, Topography, Impact of vadose zone, and hydraulic Conductivity) to characterize the hydrogeological setting and evaluate aquifer vulnerability. The western part of the Kakamigahara aquifer was dominated by "High" vulnerability classes while the eastern part was characterized by "Moderate" vulnerability classes. The elevated north-eastern part of the study area displayed "Low" aquifer vulnerability. The integrated vulnerability map shows the high risk imposed on the eastern part of the Kakamigahara aquifer due to the high pollution potential of intensive vegetable cultivation. The more vulnerable western part of the aquifer is, however, under a lower contamination risk. In Kakamigahara Heights, land use seems to be a better predictor of groundwater contamination by nitrate. Net recharge parameter inflicted the largest impact on the intrinsic vulnerability of the aquifer followed by soil media, topography, vadose zone media, and hydraulic conductivity. Sensitivity analyses indicated that the removal of net recharge, soil media and topography causes large variation in vulnerability index. Moreover, net recharge and hydraulic conductivity were found to be more effective in assessing aquifer vulnerability than assumed by the DRASTIC model. The GIS technique has provided efficient environment for analyses and high capabilities of handling large spatial data.     

Acceleration of the redox kinetics of VO2+/VO2 + and V3+/V2+ couples on carbon paper

The redox kinetics of VO²⁺/VO₂ ⁺ and V³⁺/V²⁺ couples on a carbon paper (CP, HCP030 N, Shanghai Hesen, Ltd., China) electrode were investigated in terms of their standard rate constant (k ₀) and reaction mechanism. The values determined for k ₀ for VO²⁺ ?? VO₂ ⁺ and V³⁺ ?? V²⁺ using the CP electrode are 1.0 × 10^?3 and 1.1 × 10^?3 cm s^?1, respectively. The value of k ₀ increases by one or two order(s) of magnitude compared with values obtained using electrodes composed of pyrolytic graphite and glassy carbon. The acceleration of the redox kinetics of vanadium ions is a result of the large surface area of the CP electrode. An inner-sphere mechanism for the reaction on the surface of the electrode is proposed. The kinetic features of vanadium redox reactions on the CP electrode reveal that CP is suitable for use as the electrodes in vanadium redox-flow batteries.     

Chemical reaction kinetics dataset of Cs-I-B-Mo-O-H system for evaluation of fission product chemistry under LWR severe accident conditions

In order to improve LWR source term under severe accident conditions, the first version of a fission product chemistry database named ‘ECUME’ was developed. The ECUME is intended to include several datasets of major chemical reactions and their effective kinetic constants for representative severe accident sequences. It is expected that the ECUME can serve as a fundamental basis from which fission product chemical models can be elaborated for use in the severe accident analysis codes. The implemented chemical reactions in the first version were those for representative gas species in Cs-I-B-Mo-O-H system from 300 to 3000 K. The chemical reaction kinetic constants were evaluated from either literature data or calculated values using ab-initio calculations. The sample chemical reaction calculation using the presently constructed dataset showed meaningful kinetics effects at 1000 K. Comparison of the chemical equilibrium compositions by using the dataset with those by chemical equilibrium calculations has shown rather good consistency for the representative Cs-I-B-Mo-O-H species. From these results, it was concluded that the present dataset should be useful to evaluate fission product chemistry in Cs-I-B-Mo-O-H system under LWR severe accident conditions, where kinetics effects should be considered.     

Pipe Heating System with Underground Water Tank for Snow Thawing and Ice Prevention on Roads and Bridge Decks

In order to prevent traffic accidents on snow-covered bridge decks, the writers developed a new pipe heating system that uses only groundwater stored in a large underground tank. The underground tank provides geothermal energy, i.e., groundwater of constant temperature, through heating pipes embedded in concrete pavements with no electric heater or fuel boiler. The pipe heating system was constructed at approximately 50% of the cost of comparable systems. In addition, there is a reduction of 10% in operating costs compared with the previous system. The present paper outlines its design and construction and provides fundamental data for the developed system. The piped heating system has kept the road conditions safe during the winter season by always removing the snow and ice from the heated road and bridge sections earlier than the surrounding roads. According to long-term temperature measurements, this system has prevented the road temperature from decreasing below 0°C, even through nighttime and morning periods. This report presents the system as an economical and effective solution for snow thawing and ice prevention.