The effect of structural features on mechanical properties of loose optical fiber poly(butylene terephthalate) tubes

Results of a study on the modifying mechanical properties of loose optical‐fiber poly(butylene terephthalate) (PBT) tubes, produced during the standard industrial extrusion process, show that heat treatment make the structure of their material to change. The study comprised measurements of mechanical strengths properties of the tubes (tensile strength, compression strength, kinking) and determination of tube material structure [by differential thermal analysis (DTA), wide angle X‐ray scattering analysis (WAXD), and scanning electron microscopy (SEM)]. Results of the study allowed observation that the annealing at 70°C for 34 h of the tubes caused the crystalline α phase to increase in the tube material from ～28.5% to ～31.5% and the structure of the existing crystallites to become more perfect. This made the values of certain mechanical properties of the tubes to increase even by as much as 30%. The tubes following such thermal treatment could be used in cables exposed to heavy‐duty operation in arduous environments, where a larger margin from the standpoint of mechanical properties is required. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2130–2134, 2002     

Studies on obtaining of aluminium ammonium calcium phosphates

Aluminium ammonium calcium phosphates were prepared with the use of AlCl₃, CaCO₃, H₃PO₄. The influence of the process parameters (pH 5 ± 3, the molar ratios of Ca²⁺:Al⁺³:PO₄^?3 in the substrates, respectively 0.31:0.62:1; 0.5:0.5:1; 0.72:0.36:1, temperature 40 ± 20 °C) on the phase composition and the product properties was determined. The process parameters that enable to obtain the material with expected physicochemical properties were determined based on the statistical evaluation of the experiments (fractional factorial design at three levels 3^(k?p)27). The phase composition of the obtained samples was studied with the use of XRD analysis. The specific surface area was calculated with the use of S_BET method and the particle size was determined by the laser scanning microscopy. The materials with the molar ratio of Al³⁺/NH₄⁺ and Al³⁺/Ca²⁺ in the range of 0.70–27.93 and 0.47–24.48, respectively, with an absorption oil number of 95–157 g/100 g paraffin oil, the S_BET within 25–118 m²/g, the pore volume within 0.14–0.74 cm³/g and the particle size in the range of 168–285 nm were obtained.     

Polyurethane/Polylactide-Based Electrospun Nonwovens as Carriers for Human Adipose-Derived Stromal Stem Cells and Chondrogenic Progenitor Cells

Articular cartilage dysfunctions are major cause of pain and disability and lead to serious health complications. Cell-based therapies are proposed as treatment methods for cartilage regeneration. In this study, we proposed polyurethane/poly(L-lactide-co-D, L-lactide)-based electrospun nonwovens as carriers for the delivery of human adipose-derived stromal stem cells. We found that 6:4 and 8:2 polyurethane/poly(L-lactide-co-D, L-lactide) initially enhance proliferative rate of human adipose-derived stromal stem cells, shorten their population doubling time, promote creation of functional chondrogenic nodules during chondrogenic differentiation, improve the collagen-2-to-collagen-1 protein ratio, and upregulate the expression of collagen-2 and aggrecan genes.     

The influence of electron beam irradiation,plastic deformation,and re‐irradiation on crystallinity degree,mechanical and sclerometric properties of GUR 1050 used for arthroplasty

The article describes the influence of an electron beam irradiation (I), plastic deformation (D), and re‐irradiation (R) on the properties of ultrahigh molecular weight polyethylene (GUR 1050). It was found that the modification through irradiation entailed a gradual increase in the degree of crystallinity (after irradiation–I). After plastic deformation and re‐irradiation (IDR) the degree of crystallinity decreases which had a direct influence on the mechanical properties. The polymer irradiation only (technique I) resulted in an increase in the maximum stress as compared with the material in the initial state. The application of deformation and re‐irradiation (technique IDR) allowed increasing the deformation resistance by more than 40%. Moreover, the irradiation with an electron beam resulted in the increase in hardness (H) and Young's modulus (E) proportionally to the applied irradiation dose and in the reduction of total indentation work (W_tot) and its components. After deformation and re‐irradiation the polyethylene hardness went down. The application of technique (I) caused an improvement to the material abrasion resistance (reduction of parameter PD–working scratch depth) with the increasing irradiation dose. The introduction of deformation and re‐irradiation did not have a material impact on parameter (PD) increasing at the same time elastic properties of UHMWPE (increase in parameter NPS–elastic recovery). Modification IDR has changed the wear mechanism (β) toward ploughing and has increased the abrasion‐resistance index (W_β) and also significantly reduced the coefficient of friction (μ) of GUR 1050. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43683.     

Kinetics of nucleation and growth of L-sorbose crystals in a continuous MSMPR crystallizer with draft tube: Size-independent growth model approach

The experimental data concerning kinetics of a continuous mass crystallization in L-sorbose - water system are presented and discussed. Influences of L-sorbose concentration in a feeding solution and mean residence time of suspension in a working volume of laboratory DT MSMPR crystallizer on the resulting crystal size distributions, thus on the nucleation and growth kinetics, were determined. The kinetic parameter values were evaluated on the basis of size-independent growth (SIG) kinetic model (McCabe’s ΔL law). It was observed that within the investigated range of crystallizer productivity (220–2,200 kg of L-sorbose crystals m⁻³ h⁻¹), a crystal product of mean size Lm from 0.22 to 0.28 mm and CV from 68.8 to 44.0% was withdrawn. The values of linear growth rate show increasing trend (from 6.6·10⁻⁸ to 7.6·10⁻⁸ m s⁻¹) with the productivity enlargement (assuming constant residence time τ=900 s). Occurrence of secondary nucleation phenomena within the circulated suspension, resulting from the crystals attrition and breakage was observed. The parameter values in a design equation, matching linear growth rate and suspension density with nucleation rate were determined.     

导流筒浆态连续结晶器内鸟粪石的反应结晶动力学——器内流体力学的影响

A laboratory-scale reaction-crystallization process of struvite synthesis from diluted water solution of Mg2+, and ions was studied. The research covered the tests of two original constructions of continuous jet-pump Draft Tube Magma (DTM)-type crystallizers with internal circulation of suspension (upward/downward). Interactions between constructional, hydrodynamic and kinetic factors were established and discussed. Nucleation and linear growth rates of struvite crystals were calculated on the basis of population density distribution. Kinetic model of idealized Mixed Suspension Mixed Product Removal (MSMPR) crystallizer considering the size-dependent growth mechanism was applied (Rojkowski hyperbolic equation). For comparison purposes the kinetic data corre-sponded to a simpler, continuous draft tube-type crystallizer equipped with propeller agitator were analyzed. It was concluded that crystal product of larger size was withdrawn from the jet-pump DTM crystallizer of the descending flow of suspension in a mixing chamber.     

mRNA and miRNA Expression Analyses of the MYC/E2F/miR-17-92 Network in the Most Common Pediatric Brain Tumors

Numerous molecular factors disrupt the correctness of the cell cycle process leading to the development of cancer due to increased cell proliferation. Among known causative factors of such process is abnormal gene expression. Nowadays in the light of current knowledge such alterations are frequently considered in the context of mRNA–miRNA correlation. One of the molecular factors with potential value in tumorigenesis is the feedback loop between MYC and E2F genes in which miR-17-5p and miR-20a from the miR-17-92 cluster are involved. The current literature shows that overexpression of the members of the OncomiR-1 are involved in the development of many solid tumors. In the present work, we investigated the expression of components of the MYC/E2F/miR-17-92 network and their closely related elements including members of MYC and E2F families and miRNAs from two paralogs of miR-17-92: miR-106b-25 and miR-106a-363, in the most common brain tumors of childhood, pilocytic astrocytoma (PA), WHO grade 1; ependymoma (EP), WHO grade 2; and medulloblastoma (MB), WHO grade 4. We showed that the highest gene expression was observed in the MYC family for MYCN and in the E2F family for E2F2. Positive correlation was observed between the gene expression and tumor grade and type, with the highest expression being noted for medulloblastomas, followed by ependymomas, and the lowest for pilocytic astrocytomas. Most members of miR-17-92, miR-106a-363 and miR-106b-25 clusters were upregulated and the highest expression was noted for miR-18a and miR-18b. The rest of the miRNAs, including miR-19a, miR-92a, miR-106a, miR-93, or miR-25 also showed high values. miR-17-5p, miR-20a obtained a high level of expression in medulloblastomas and ependymomas, while close to the control in the pilocytic astrocytoma samples. miRNA expression also depended on tumor grade and histology.     

Stem Photosynthesis—A Key Element of Grass Pea (Lathyrus sativus L.) Acclimatisation to Salinity

Grass pea (Lathyrus sativus) is a leguminous plant of outstanding tolerance to abiotic stress. The aim of the presented study was to describe the mechanism of grass pea (Lathyrus sativus L.) photosynthetic apparatus acclimatisation strategies to salinity stress. The seedlings were cultivated in a hydroponic system in media containing various concentrations of NaCl (0, 50, and 100 mM), imitating none, moderate, and severe salinity, respectively, for three weeks. In order to characterise the function and structure of the photosynthetic apparatus, Chl a fluorescence, gas exchange measurements, proteome analysis, and Fourier-transform infrared spectroscopy (FT-IR) analysis were done inter alia. Significant differences in the response of the leaf and stem photosynthetic apparatus to severe salt stress were observed. Leaves became the place of harmful ion (Na⁺) accumulation, and the efficiency of their carboxylation decreased sharply. In turn, in stems, the reconstruction of the photosynthetic apparatus (antenna and photosystem complexes) activated alternative electron transport pathways, leading to effective ATP synthesis, which is required for the efficient translocation of Na⁺ to leaves. These changes enabled efficient stem carboxylation and made them the main source of assimilates. The observed changes indicate the high plasticity of grass pea photosynthetic apparatus, providing an effective mechanism of tolerance to salinity stress.     

Tribological Properties of the Oxide Coatings Produced onto 6061-T6 Aluminum Alloy in the Hard Anodizing Process

The aim of this work was to establish the influence of the thickness of the anodic coatings on their mechanical properties and to understand the relation between their hardness and the abrasion resistance. The coatings were produced in the hard anodizing process onto the 6061-T6 aluminum alloy. Their thickness was in the range between 19 and 43 µm. The abrasion resistance was determined by using Taber abrasion test. The weight losses of the coatings obtained were in the range between 15 and 11 mg and decreased with their increasing thickness. It has been shown that the hardness measured on the cross sections of the coatings did not correspond to their abrasion resistance. Thus, the new approach has been proposed. The hardness of the coatings was estimated on the basis of the results of the scratch test performed at the constant load. The results obtained correspond to the abrasion resistance of the coatings.