Amperometric determination of tyramine in sauce and beer by epoxy resin biocomposite membrane bound tyramine oxidase

A method is described for construction of an amperometric biosensor for specific determination of tyramine, using black gram tyramine oxidase immobilized covalently on an epoxy resin membrane. The biosensor had optimum response within 10 s at pH 8.5 and 35 °C. A linear relationship was observed between tyramine concentrations and current (mA) in the range of 0.24 to 3.47 mg/dL. The biosensor was employed for determination of tyramine in beer and sauce. The detection limit of sensor was 0.24 mg/dL. The mean analytical recovery of added tyramine (0.5 and 1.0 mg/dL) was 97.3 ± 2.3 and 95.9 ± 3.4%. Within and between batch coefficient of variation were 5.1 and 5.34%, respectively. Enzyme electrode showed 35% loss in its initial activity after its regular use over a period of 2 months. The biosensor has the advantage that it does not suffer from leaching of enzyme and measures tyramine specifically.     

Isatin compounds as corrosion inhibitors for N80 steel in 15% HCl

The inhibition effect of two synthesized isatin compounds namely 1-morpholinomethyl-3-(1-N-dithiooxamide)iminoisatin [MMTOI] and 1-diphenylaminomethyl-3-(1-N-dithiooxamide)iminoisatin [PAMTOI] on the corrosion inhibition of N80 steel in 15% HCl solution was studied by polarization, EIS and weight loss measurements. It was found that both the inhibitors were effective and their inhibition efficiency was significantly increased with increasing concentration. Polarization curves revealed that the used inhibitors represent mixed-type inhibitors. Adsorption of these inhibitors led to a reduction in the double layer capacitance and an increase in the charge transfer resistance, and was found also to obey Langmuir isotherm.     

NAFLA – Ein Simulationswerkzeug zur analytischen Abschätzung von Schadstofffahnenlängen

Groundwater pollution with organic contaminants remains a world-wide problem. Before selection of any remediation technique, it is important to pre-assess contaminated sites with respect to their hazard. For this, several analytical and numerical approaches have been used and an initial assessment of contaminated sites the MS-Excel^© tool “NAFLA” was developed. “NAFLA” allows a quick and straightforward calculation and comparison of some analytical approaches for the estimation of maximum plume length under steady-state conditions. These approaches differ from each other in source geometry, model domain orientation, and in the consideration of (bio)chemical reaction within the domain. In this communication, we provide details about the development of “NAFLA”, its possible usage and information for users. The tool is especially designed for application in student education, by authorities and consultants.     

Synthesis and characterization of Cu nanotubes and nanothreads by electrical arc evaporation

We report the formation and characterization of copper nanostructures, nanotubules and nanothreads, which were obtained by electrical arc evaporation of Cu electrodes under varied conditions of He ambience. Electrical arc evaporation was done with approximately 10 V and (approximately 50-100 A) DC current. The current was used in a pulse mode. The evaporated material was condensed on a formvar-coated Cu grid mounted on a liquid N2-cooled specimen holder. Transmission electron microscopy was employed to characterize the condensed materials. These investigations revealed that the condensed materials consisted of the mentioned nanostructures. Nanotubes and nanothreads are formed for a He pressure in the chamber corresponding to approximately 140 and approximately 500 torr, respectively. Extensive electron microscopic investigations showed that the diameter of the nanotubes varied from approximately 5 nm to approximately 50 nm and their length from 2 microns to 3 microns.     

Extractability and phytotoxicity of heavy metals present in petrochemical industry sludge

Bioavailability of heavy metals present in industrial sludges and their subsequent phytotoxicity are crucial parameters to assess the associated health hazards and suitability for land application. The present study is an effort to determine the extractability of heavy metals present in different phases of the sludges, coming out of two different operations involved in petrochemical industry viz. spent caustic treatment (SCT) and waste water treatment (WWT) following the BCR sequential extraction procedure. The maximum amount of Cd and Cu was found associated with oxidizable phase, whereas Cr and Ni were best recovered in residual fractions of both the sludges. Maximum Pb was recovered in oxidizable and residual phase in the WWT and SCT sludges, respectively. The stabilization treatment undergone by sludges strongly influenced the heavy metal distribution and the phases to which they were associated. The total metal concentration in both the sludges did not exceed the limit set out by the European Legislation and was found as Cd = 0.449, Pb = 3.340, Ni = 6.530, Cr = 21.087, & Cu = 27.129 μg g^?1 and Cd = 0.549, Pb = 5.664, Ni = 7.161, Cr = 27.096, & Cu = 35.479 μg g^?1 in the SCT and WWT sludges, respectively. Phytotoxicity of the sludges was assessed against the germination index and the relative root and shoot growth. Sludge leachates did not adversely affect the seed germination and the early seedling growth of Mung (Phaseolus mungo) and Gram (Cicer arietinum), indicating that these metals were concentrated in the non-bioavailable fractions of sludges.     

Determination of the flow stress of five AHSS sheet materials (DP 600, DP 780, DP 780-CR,DP 780-HY and TRIP 780) using the uniaxial tensile and the biaxial Viscous Pressure Bulge (VPB) tests

Room temperature uniaxial tensile and biaxial Viscous Pressure Bulge (VPB) tests were conducted for five Advanced High Strength Steels (AHSS) sheet materials, and the resulting flow stress curves were compared. Strain ratios (R-values) were also determined in the tensile test and used to correct the biaxial flow stress curves for anisotropy. The pressure vs. dome height raw data in the VPB test was extrapolated to the burst pressure to obtain the flow stress curve until fracture. Results of this work show that the flow stress data can be obtained to higher strain values under biaxial state of stress. Moreover, it was observed that some materials behave differently if subjected to different state of stress. These two conclusions, and the fact that the state of stress in actual stamping processes is almost always biaxial, suggest that the bulge test is a more suitable test for obtaining the flow stress of AHSS sheet materials for use as an input to Finite Element (FE) simulation models.     

Combustion synthesis of compounds in the Y2O3-Al2O3 system

In the Y₂O₃-Al₂O₃ system, compounds Y₃Al₅O₁₂ (yttrium aluminum garnet, YAG), YAlO₃ (yttrium aluminum perovskite, YAP), and Y₄Al₂O₉ (yttrium aluminate monoclinic, YAM) are well known. YAG and YAP are of considerable technological importance. Conventional solid-state reaction techniques require high sintering temperatures (above 1800°C) to prepare phase-pure compounds. Though several soft chemical routes have been explored for synthesis of YAG, YAP and YAM, most of these methods are complex. Moreover, phase-pure materials are not obtained in one step and prolonged annealing at temperatures around 1000°C is necessary. In this paper, one-step combustion synthesis of these compounds is reported using a modified procedure and employing mixed (glycine + urea) fuel. Phosphors based on Ce³⁺ activation were also prepared and exhibited characteristic photoluminescence.     

Guest–host interaction in ferroelectric liquid crystal–nanoparticle composite system

The present paper deals with the characterization of a ferroelectric liquid crystal–nanoparticle (FLC–NP) composite system. The dielectric, electrical and polarization property of the FLC–NP composite system have been studied as a function of temperature and frequency. Ferroelectric Cu-doped ZnO (Cu–ZnO) nanoparticles have been added to the pure ferroelectric liquid crystal (FLC) Felix 17/100. The nanoparticles are bigger in size as compared to FLC molecules; therefore, they distort the existing geometry of FLC matrix and set up an antiparallel correlation with the dipole moments of the host FLC molecules. This antiparallel correlation of guest–host geometry reduces the net ferroelectricity of the composite system and modifies all the physical properties of the pure FLC. The change in properties has been analysed and explained in the light of guest–host interaction.     

Morphology optimization for achieving air stable and high performance organic field effect transistors

To develop an all organic active matrix light emitting display required for large area thin display, electronic paper and electronic paints, Si-based thin film transistor has to be replaced with organic thin film transistor (OTFT). The most important issues in OTFT are the low charge carrier mobility and poor stability under ambient conditions, which critically depend on how organic thin films are grown on different substrates. Here we show that both these issues are correlated and can be overcome by certain surface morphology which can only be achieved through anisotropic growth. Careful control of different growth parameters can lead to unprecedented control on thin film morphology which has been shown to be engineered reversibly and reproducibly. High temperature and low evaporation rate increase the diffusive mobility of molecules, which are responsible for the stacking of molecules to higher length scales. By carefully choosing a temperature and evaporation rate, elongated rod-like grains were grown for achieving high performance and stable thin film transistors.