Broad-band MMICs based on modified loss-compensation method using 0.35-/spl mu/m SiGe BiCMOS technology

Using the concept of loss compensation, novel broad-band monolithic microwave integrated circuits (MMICs), including an amplifier and an analog multiplier/mixer, with LC ladder matching networks in a commercial 0.35-mum SiGe BiCMOS technology are demonstrated for the first time. An HBT two-stage cascade single-stage distributed amplifier (2-CSSDA) using the modified loss-compensation technique is presented. It demonstrates a small-signal gain of better than 15 dB from dc to 28 GHz (gain-bandwidth product=157 GHz) with a low power consumption of 48 mW and a miniature chip size of 0.63 mm² including testing pads. The gain-bandwidth product of the modified loss-compensated CSSDA is improved approximately 68% compared with the conventional attenuation-compensation technique. The wide-band amplifier achieves a high gain-bandwidth product with the lowest power consumption and smallest chip size. The broad-band mixer designed using a Gilbert cell with the modified loss-compensation technique achieves a measured power conversion gain of 19 dB with a 3-dB bandwidth from 0.1 to 23 GHz, which is the highest gain-bandwidth product of operation among previously reported MMIC mixers. As an analog multiplier, the measured sensitivity is better than 3000 V/W from 0.1 to 25 GHz, and the measured low-frequency noise floor and corner frequency can be estimated to be 20 nV/sqrt(Hz) and 1.2 kHz, respectively. The mixer performance represents state-of-the-art result of the MMIC broad-band mixers using commercial silicon-based technologies     

Viable：设计折射生活体验

从上个世纪九十年代中期开始，无定型的造型在设计中占据了主导。十年之后，人们的审美和设计标准发生了变化。几何原理的广泛应用使得生活物品的设计出现了“硬边”（产品的棱线和轮廓）与“精确”之风的回潮。也许是人们渴望在这个不稳定的世界中寻求稳定的元素，也许是为了用简单直白的设计来掩饰以往设计中复杂计算的造型。总之，设计师对成熟稳重的几何形式表现得情有独钟。这种席卷而来的感觉体现了一种设计的成熟，而Viable工作室的设计就是其中的代表；不仅如此，他们的设计还反映出了每个人对生活的不同理解。[编者按]     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Workplane illuminance prediction method for daylighting control systems

A new prediction method with an interior light sensor for the workplane illuminance in daylighting control systems is introduced. Based on radiosity theory, the spatial distributions of daylight and electric light in the space are discussed and the prediction method is developed. An experimental verification of the technique is performed in an outdoor test-room for a double-glazed window system with a motorized venetian blind integrated between the two glazings. Electric light and daylight predictions were performed in accordance with the proposed method. The results showed that the electric light workplane illuminance can be predicted with high accuracy (±5 lux error with a linear correlation) and that the daylight workplane illuminance can be predicted within ±20 lux (with a linear correlation) for any sky conditions (overcast, clear sky, or variable) with the window system controlled to prevent direct daylight transmission. This method is useful for integrated control of motorized daylighting devices and dimmable electric lights.