Amelioration of mechanical brittleness in hyperbranched polymer. 1. Macroscopic evaluation by dynamic viscoelastic relaxation

Hyperbranched poly(ether ketone)-b-linear poly(ether ketone)-b-hyperbranched poly(ether ketone) (HLHPEK) triblock copolymers with two different block compositions were prepared as an approach to improve the mechanical brittleness of hyperbranched poly(ether ketone) (HPEK). From the time-temperature superposition of dynamic shear moduli, G′(ω) and G″(ω), of HPEK and two HLHPEKs, it was investigated that the junction points between G′(ω) and G″(ω) shifted to the higher frequencies and the rubbery plateau region spread wider over the reduced frequency axis as the linear blocks were introduced and their compositions were increased. Such changes in viscoelastic response were consequences of increase in the amount of chain entanglements additionally formed by the linear blocks. In order to verify the effect of the linear block incorporation on amelioration of the mechanical brittleness, the degree of brittleness and its improvement were evaluated from the temperature dependence of the shift factors, a_Ts, experimentally obtained during the superposition of the dynamic moduli and of the average viscoelastic relaxation times, τ_HNs, determined with empirical Havriliak-Negami distribution function. From the nonlinear curve fittings of the a_Ts and the τ_HNs by the Vogel-Tamman-Fulcher equation, the degree of brittleness for HPEK and HLHPEK triblock copolymers were quantified as values of the material parameter D, an indicative of deviation from the linear Arrhenius behavior and a measure of fragility of the given material. The tendency of increasing D values with the linear block compositions confirmed substantial improvement of the mechanical brittleness in the HLHPEK triblock copolymers compared to HPEK. Therefore, the approach to copolymerize HPEK with its chemically analogous linear counterpart was verified to be an effective strategy to impart molecular entanglements and hence ameliorate the mechanical brittleness on the basis of macroscopic rheological evaluation.     

Zeolite Formation in Class F Fly Ash Blended Cement Pastes

Zeolite formation in Class F fly ash blended cement pastes is under investigation. A Na–P type zeolite and Zeolite Y were synthesized from Class F fly ash and NaOH solution after 2 days of aging at room temperature and 6 days of curing at 80°C. However, no zeolites formed when KOH was used. In additional experiments, a Na–P type zeolite, Zeolite Y, and chabazite developed in cement pastes blended with Class F fly ash and NaOH solution which had been aged 2 days at room temperature and then cured 6 days at temperatures ranging from room temperature to 90°C. Seeding the pastes with natural zeolites was also investigated.     

Influences of metallic polymeric materials on the properties of fresh polyester and acrylic polymer concrete

To investigate the influences of three metallic polymeric materials in polyester and acrylic fresh polymer concretes (PCs), PC‐incorporated different levels of these materials have been investigated for their properties of fresh PC. The mix design was made and optimized for workability, strength, and economy, depending on the resin viscosity, the intended use, and the additional quantities of these polymeric materials. The properties investigated include workability, working time, and curing time of fresh PC. It is concluded that these polymeric materials offer the possibility of improving properties of polyester and acrylic fresh polymer concretes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Effects of diacrylate monomers on the mechanical properties of polymer concrete made with wet aggregates

Because normal polymer concrete does not work well with wet aggregates, diacrylate (DA) monomers were evaluated for improving the mechanical properties of polymer concrete made with wet aggregates. Zinc diacrylate (ZDA) and calcium diacrylate (CDA) were each used as an additive to resins (two epoxies). The variables were the amount of diacrylate monomers and the aggregate conditions (wet or dry). Compressive strength, flexural strength, workability, working time, and curing time were measured. ZDA was found to improve the workability and the working time, and CDA was found to improve the compressive and the flexural strength. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1077–1085, 2004     

Binary blends of nylons with ethylene vinyl alcohol copolymers: Morphological,thermal, rheological,and mechanical behavior

Binary blends of ethylene vinyl alcohol copolymers, containing 62 (EVOH-62) and 71 (EVOH-71) mole percent vinyl alcohols, with nylons (nylon-6, nylon-6/12, and nylon-12) have been prepared from melt mixing in a twin screw compounding machine. Morphological, thermal, rheological, and mechanical properties were determined. EVOH-62/nylon-6 and EVOH-71/nylon-6 blends showed homogeneous phase morphologies in the nylon-6-rich region, and fine phase separations (c.a. 2 × 10^?7 m) in the EVOH-rich region. Melting point depression, positive deviations in viscosity and flexural modulus, and negative deviation in impact strength from the simple additive rule were generally observed. And the results were possibly interpreted in terms of compatibility and increased nylon/EVOH interactions over the nylon/nylon interactions. On the contrary, clean phase separations in large domains were observed from EVOH-71/nylon-6/12 and EVOH-71 /nylon-12 blends. Fibrillation was also obtained from EVOH rich blends. Probably due to the incompatible nature of these blends, yield at low rate of shear and a mechanical property drop were also observed.     

Adhesion property of novel polyimides with 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride

Novel polyimides were synthesized from 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride (6FPPMDA) by a conventional two‐step process: the preparation of poly(amic acid) followed by solution imidization via refluxing in p‐chlorophenol. The diamines used for polyimide synthesis included bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, bis(3‐aminophenyl)‐4‐trifluoromethylphenyl phosphine oxide, and bis(3‐aminophenyl)phenyl phosphine oxide. The synthesized polyimides were designed to have a molecular weight of 20,000 g/mol by off‐stoichiometry and were characterized by Fourier transform infrared, NMR, differential scanning calorimetry, and thermogravimetric analysis. In addition, their intrinsic viscosity, solubility, water absorption, and coefficient of thermal expansion (CTE) were also measured. The adhesion properties of the polyimides were evaluated via a T‐peel test with bare and silane/Cr‐coated Cu foils, and the failure surfaces were investigated with scanning electron microscopy. The 6FPPMDA‐based polyimides exhibited high glass‐transition temperatures (280–299°C), good thermal stability (>530°C in air), low water absorption (1.46–2.16 wt %), and fairly low CTEs (32–40 ppm/°C), in addition to good adhesion properties (83–88 g/mm) with silane/Cr‐coated Cu foils. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1801–1809, 2005     

Polymer gel electrolytes prepared from P(EG‐co‐PG) and their nanocomposites using organically modified montmorillonite

Polymer gel electrolytes were prepared by thermal crosslinking reaction of a series of acrylic end‐capped poly(ethylene glycol) and poly(propylene glycol) [P(EG‐co‐PG)] having various geometries and molecular weights. Acrylic end‐capped prepolymers were prepared by the esterification of low molecular weight (M_n: 1900–5000) P(EG‐co‐PG) with acrylic acid. The linear increase in the ionic conductivity of polymer gel electrolyte films was observed with increasing temperature. The increase in the conductivity was also monitored by increasing the molecular weight of precursor polymer. Nanocomposite electrolytes were prepared by the addition of 5 wt % of organically modified layered silicate (montmorillonite) into the gel polymer electrolytes. The enhancement of the ionic conductivity as well as mechanical properties was observed in the nanocomposite systems. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 894–899, 2004     

Molecular simulation of hydrogen adsorption in organic zeolite

The adsorption of molecular hydrogen on model zeolites has been simulated employing Grand Canonical Monte Carlo (GCMC) procedure. The effects of cation type, available volume, surface area, temperature, pressure and pre-adsorbed organics such as benzene on the hydrogen uptake are analyzed. The hydrogen adsorption can be affected mainly by the available volume and surface area per g-zeolite at the same temperature and pressure. Increase of temperature results in the decrease of sorption intensity and capacity. The adsorption capacity correlates well with the pressure with high linearity at room temperature. Adsorption is lowered by the pre-adsorbed benzene molecule. The orientation and the number of benzene molecule in zeolite affect the adsorption capacity. The organic zeolite with larger available volume shows larger adsorption capacity.     

High catalytic activity of PdOx/MnO2 for CO oxidation and importance of oxidation state of Mn

PdO_x/MnO₂ has been examined as a catalyst for CO oxidation using a conventional flow reactor at reaction temperatures between 50 and 150°C. In the reaction conditions of GHSV (gashourlyspacevelocity) of 1.22 × 10⁵/h and CO concentration of 2000 ppm, PdO_x/MnO₂ showed higher catalytic activity compared with PdO_x/Mn₂O₃, which had been previously reported as an effective catalyst due to the cooperative action of Pd and Mn₂O₃ for this reaction. The reason for higher activity of PdO_x/MnO₂ than PdO_x/Mn₂O₃ has been investigated using TPR (temperatureprogrammed reduction) and XPS studies. TPR showed that PdO_x/MnO₂ could be reduced by CO at much lower temperature than PdO_x/Mn₂O₃. During the experiment of reduction and oxidation, XPS showed that the valence of Mn in the PdO_x/MnO₂ was between 4+ and 3+, which is higher than that of Mn in the PdO_x/Mn₂O₃ catalyst of which the valence has been reported to be between 3+ and 2+. It is known that in this catalyst system the support supplies oxygen onto Pd, where the oxidation occurs with adsorbed CO, and the ability of the support to provide oxygen improves the performance of the catalyst. Therefore, it was concluded that the readiness of MnO₂ to be reduced with maintaining a higher oxidation state showed higher CO oxidation activity than Mn₂O₃ as support for PdO_x.     

Absorption of NO x in packed column (I)

A mathematical model for an absorption of nitrogen oxides into water in packed column was developed based on the mass-transfer coefficient in packed column and the chemical reaction accompanying NO _x absorption produces HNO₃ and HNO₂ in the liquid phase. The subsequent dissociation of HNO₂ in the liquid-phase results in the formation of HNO₃ and NO gas, and then this NO gas follows to be oxidized by O₂ in air. The important factors influenced on the absorption of NO _x are the oxidation state of NO gas and the partial pressure of nitrogen oxides in the gas. The efficiency of NO _x absorption increases with the increase of the partial pressure of NO _x . The most critical value for using the model is the constant of .The selection of 11×10⁻⁴kg·mol/atm·m²·sec for resonable for this model.