海底电缆交叉鬼波化双检合并技术改进及应用

双检合并技术在海底电缆地震资料处理中被广泛应用,可衰减电缆鬼波的影响。传统方式以水、陆检记录的波场记录相同为假设,电缆鬼波压制效果差,合并效果并不理想。在分析交叉鬼波化双检合并技术基本原理的基础上,综合利用水检资料与陆检鬼波褶积的结果和陆检资料与水检鬼波褶积的结果求取刻度算子,同时在地震资料处理中利用陆检资料标定水检资料,从而优化了交叉鬼波化双检合并技术。实际资料处理结果表明,改进后的技术可有效衰减电缆鬼波,分离出上行波场,大幅度拓宽地震资料频带,提高地震资料分辨率,从而提供更丰富的构造细节信息。     

Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

快速切换(SMED)在空调制造厂的研究与应用

在目前市场需求呈现规模扩张和品类个性化的冲击下,制造业面对的竞争压力愈发明显.且随着新时代自动化、信息化、大数据智能化等先进制造特征的兴起,更加促使制造业向转型升级不断进军.以空调制造业的控制器版块为例,从制约此单位效率的SMT车间切换浪费为切入点,在SMED快速换模的理念基础上,通过使用IE分析工具对切换流程进行研究,提炼出一套多模组固定料站切换模型,同时结合自动化、信息化等智能制造技术引进,完成SMT车间人力投入减少35人,日均产出点数提升18.29％,设备运行率提升15.46％,综合成本降低110.6万元/年的效益.成功推广应用至电子物料拣选版块,并开发信息化看板,夯实应用效益,再次证实"多模组固定料站"快速切换模型是典型小、多、高生产模式,具有可行性的解决方案.     

Facile synthesis of Li 2 ZrO 3 -modified LiNi 0.5 Mn 0.5 O 2 cathode material from a mechanical milling route for lithium-ion batteries

Li2ZrO3-modified LiNi0.5Mn0.5O2 materials with improved electrochemical performance were directly synthesized by a simple mechanical milling route with ZrO2, Li2CO3 and Ni0.5Mn0.5(OH)2 precursors...     

Polyethylene oxide-polypropylene oxide -polyethylene oxide derived porous carbon materials with different molecular weights as ORR catalyst in alkaline electrolytes

Polyethylene oxide (PEO)-polypropylene oxide (PPO)-polyethylene oxide block copolymer having different molecular weights are used as precursors of carbon materials to prepare Hollow -Derivatives carbon material as an electrocatalyst through block copolymer self-assembly. The composition and microstructure of the prepared catalysts are shown by Raman spectroscopy, X-ray diffraction (XRD), Test of nitrogen adsorption and desorption curves, High resolution transmission electron microscopy (HR-TEM) and scanning electron microscopy (HR-SEM). Oxygen was passed into alkaline electrolyte solution until the solution reached saturation state. With molecular weight increasing, the obtained sample gradually changed from block to hollow and spherical. When the molecular weight was 12600 g mol^?1, the evenly hollow carbon nanocages was acquired (C-12600). In O₂ saturated alkaline electrolyte (0.1 M KOH solution), C-12600's limited current density，half-wave potential and initial potential are 5.23 mA cm^?2@0.4 V, 0.72 V and 0.81 V, respectively. And most important is that half-wave potential and onset potential have barely change after 2000 cycles of cyclic voltammetry. As a result, the porous carbon materials exhibited excellent electrocatalytic activity while maintaining high stability in alkaline KOH solution.     

In situ characterization of LiY(WO4)2 nanotubes for electrochemical energy storage

Here, LiY(WO₄)₂ nanotubes are prepared via a feasible electrospinning technique. This new anode material shows excellent electrochemical properties. The capacity loss of LiY(WO₄)₂ nanotubes is as low as 6.9% after 156 cycles, while bulk LiY(WO₄)₂ presents the capacity loss higher than 55.0%. Even after 600 long-life cycles, the capacity loss of the nanotubes is only 9%. It can be seen that the hollow structure with a rough surface and a porous morphology contributes to the improvement of electrochemical performance. Furthermore, online X-ray diffraction (XRD) method is firstly applied to understand the lithium ions insertion/extraction mechanism of LiY(WO₄)₂ nanotubes. It can be concluded that it is an asymmetrical two-phase reaction. A phase transformation from LiY(WO₄)₂ to Li₃Y(WO₄)₂ can be obviously seen from the in situ XRD during discharge process. While Li₂Y(WO₄)₂ appears as an intermediate phase with a reverse charge reaction. In addition, in situ XRD also demonstrates that LiY(WO₄)₂ nanotubes have surprised electrochemical reversibility. All the above results indicate that LiY(WO₄)₂ nanotubes can be expected to be anode candidate for rechargeable lithium ion batteries (LIBs).