A case study of regional catchment water quality modelling to identify pollution control requirements.

There are four ecologically important river catchments that contain candidate Special Areas of Conservation (cSACs) under the Habitats Directive in the Lake District National Park located in the North of England. These are the rivers Ehen, Kent, Derwent and Eden. For each cSAC, there are defined ecological criteria that include water quality targets to protect the designated species. Stretches of the riverine cSACs in each catchment are failing to meet these and other water quality targets. The Environment Agency commissioned a study of each catchment to provide the underpinning scientific knowledge to allow it to deliver its statutory obligations under the Habitats Directive. SIMCAT river water quality models were produced and used to predict the water quality impacts resulting from a number of water quality planning scenarios aimed at achieving full compliance with the Habitats Directive and other national and EEC water quality targets. The results indicated that further controls on effluent discharges will allow the majority of targets to be met but other sources of pollution will also need to be controlled. The outcome of the study also recognised that water quality improvements alone will not necessarily produce the required improvement to the ecological interest features in each cSAC.     

Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

A series active power filter based on a sinusoidalcurrent-controlled voltage-source inverter

A series active power filter working as a sinusoidal current source, in-phase with the mains voltage, has been developed and tested. The amplitude of the fundamental current in the series filter is controlled through the error signal generated between the load voltage and a pre-established reference. The control allows an effective correction of power factor, harmonic distortion and load voltage regulation. Compared with previous methods of control developed for series active filters, this method is simpler to implement because it is only required to generate a sinusoidal current, in-phase with the mains voltage, the amplitude of which is controlled through the error in the load voltage. The proposed system has been studied analytically and tested using computer simulations and experiments. In the experiments, it has been verified that the filter keeps the line current almost sinusoidal and in-phase with the line voltage supply. It also responds very quickly under sudden changes in load conditions, reaching its steady-state in about two cycles of the fundamental     

Monte Carlo simulations of homogeneous upconversion in erbium-dopedsilica glasses

Quenching of Er³⁺ ions by homogeneous energy-transfer upconversion in high-concentration erbium-doped silica glasses has been theoretically investigated, The results indicate that at Er³⁺ concentrations of 1.0-2.0·10²⁶ m^-3 or below, the kinetic limit of strong migration is not reached, and hence the widely accepted quadratic upconversion model is not generally valid. Nevertheless, the results offer an explanation of the experimental observations of quadratic upconversion. Furthermore, it has been shown that at a given population inversion, the quenching rate depends on the rate of exchange of the excited Er³⁺ ions by emission and absorption     

Optical imaging of anatomical maps derived from magnetic resonanceimages using time-independent optical sources

Presents a model suitable for computing images of absorption cross sections of thick tissue structures illuminated at near infrared (NIR) wavelengths from tomographic projection data. Image reconstruction is accomplished by solving a system of linear equations derived from transport theory. Reconstruction results using different algebraic solvers are shown for anatomical maps of the breast, derived from magnetic resonance imaging data, containing two simulated pathologies, in which case qualitatively good reconstructions were obtained. Evaluation of magnetic resonance (MR) data to optimize NIR optical tomographic imaging methods and to assess the feasibility of a combined MR-optical measurement scheme is discussed     

Assessing Environmental Risks: Lessons From Superfund

This essay analyzes the use of risk assessment in Superfund, the controversial American hazardous waste cleanup programme. We argue that risk assessment has been used in three ways in discussing policy options in this programme: as a metric for assessing performance; as a means for resolving conflicts; and as a tool for comparing different environmental initiatives. Use of risk reduction as an analytical tool in European efforts to clean up hazardous waste sites is discussed. We conclude that while risk assessment has potential utility for each of these applications, there are also accompanying technical and political difficulties.     

Cable insulation density profile determined from ultrasonicvelocity measurements

Density results obtained on the same cable sample with a column and from ultrasonic measurements are reported. A calibration curve relating ultrasonic velocity and cable insulation density is given for PE and crosslinked PE (XLPE) cables. The limits and advantages of deducing density profiles of cable insulation using a focused, ultrasound beam rather than the more time-consuming column measurements are discussed     

Application of evolutionary programming to transient andsubtransient parameter estimation

This paper presents an artificial intelligence approach of using evolutionary programming to estimate the transient and subtransient parameters of a generator under normal operation. The estimation using evolutionary programming is compared with that using a corrected extended Kalman filter. The comparisons with both simulation and micromachine test results show that evolutionary programming is robust to search the real values of parameters even when the data are highly contaminated by noise, while with the extended Kalman filter, the estimation tends to diverge with such data