Cable insulation density profile determined from ultrasonicvelocity measurements

Density results obtained on the same cable sample with a column and from ultrasonic measurements are reported. A calibration curve relating ultrasonic velocity and cable insulation density is given for PE and crosslinked PE (XLPE) cables. The limits and advantages of deducing density profiles of cable insulation using a focused, ultrasound beam rather than the more time-consuming column measurements are discussed     

β″－Al_2O_3陶瓷的强化和韧化

研究了稳定ＺｒＯ＿２和部份稳定ＺｒＯ＿２对β″－Ａｌ＿２Ｏ＿３陶瓷的强化和韧化作用，观察了不同种类、不同含量的ＺｒＯ＿２对β″－Ａｌ＿２Ｏ＿３陶瓷的显微结构、力学性能和电导率的影响，探讨了β″－Ａｌ＿２Ｏ＿３的韧化机理。     

Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

Application of evolutionary programming to transient andsubtransient parameter estimation

This paper presents an artificial intelligence approach of using evolutionary programming to estimate the transient and subtransient parameters of a generator under normal operation. The estimation using evolutionary programming is compared with that using a corrected extended Kalman filter. The comparisons with both simulation and micromachine test results show that evolutionary programming is robust to search the real values of parameters even when the data are highly contaminated by noise, while with the extended Kalman filter, the estimation tends to diverge with such data     

A new erasing method for a single-voltage long-endurance flashmemory

A new method to erase a standard (double-poly, stacked-gate NOR-type) flash cell is proposed. The method, still using the tunneling mechanism to extract electrons from the floating gate, is based on the concept of keeping the electric field constant during the whole erasing operation. The new method has two main advantages with respect to the conventional one: (1) it does not depend on the supply voltage variation and (2) it allows a better reliability in terms of endurance-induced stress. Results have shown that flash device performances are greatly improved in terms of stability and endurance reliability up to one million cycles     

Ultralow-voltage boron-doped diamond field emitter vacuum diode

A boron-doped diamond field emitter diode with ultralow turn-on voltage and high emission current is reported. The diamond field emitter diode structure with a built-in cap was fabricated using molds and electrostatic bonding techniques. The emission current versus anode voltage of the capped diamond emitter diode with boron doping, sp² content, and vacuum thermal electric (VTE) treatment shows a very low turn-on voltage of 2 V. A high emission current of 1 μA at an anode voltage of less than 10 V can be obtained from a single diamond tip. The turn-on voltage is significantly lower than comparable silicon field emitters     

Lamp configuration design for rapid thermal processing systems

We have studied lamp configuration design for rapid thermal processing (RTP) systems. We considered a configuration consisting of four concentric circular lamp zones, three of them above the wafer and one circumventing the wafer. We propose a method to determine the geometric parameters, the width, height and radius, of the lamp zones so that the configuration designed has the capacity to achieve a uniform temperature on the wafer. The method is based on a necessary and sufficient condition for uniform temperature tracking and analytic expressions of the view factors. A design example is given in which a least square open-loop control law yields good temperature uniformity     

A novel method for elimination of line-current harmonics insingle-stage PFC switching regulators

This paper studies a particular single-stage power-factor-correction (PFC) switching regulator employing a discontinuous-conduction-mode (DCM) boost-input cell and a continuous-current-mode (CCM) forward output cell. Although this single-stage PFC regulator can provide a reasonably high power factor when its PFC stage is operating in discontinuous mode, substantial reduction in line-current harmonics is possible by applying a suitable frequency-modulation scheme. This paper derives a frequency-modulation scheme and proposes a practical implementation using a simple translinear analog circuit. A quantitative analysis on the total harmonic distortion (THD) of the line current when the circuit is subject to a limited range of frequency variations is presented along with some considerations for practical design. Experimental data obtained from a prototype confirms the effectiveness of the proposed frequency-modulation scheme. The proposed analog translinear circuit allows custom integrated circuit implementation, making it a viable low-cost solution to the elimination of line-current harmonics in switching regulators