变异函数在进间砂体预测中的应用

应用变异函数探讨了砂体的定量预测问题。通过对北二东密井网试验区不同类型砂体，不同井网密和岩厚度的预测，检验了此方法的精度（为70％左右），在原方法的基础上，通过对预报精度的分析并结合精度地质研究进一步完善了该方法，提出二次建模法并应用于北二东西块聚驱井的砂岩厚度预测中，预测精度可提高5％以上，从而说明应用变异函数研究砂体的定量预测问题具有可借鉴性，可以为今后新井调整厚度的预测及砂体描述提供依据。     

蒸馏与减粘热联合装置的设备腐蚀及防护

介绍了锦西石化分公司南蒸馏与减粘热联合装置炼制辽河高酸值原油及带炼高硫进口油在 2 0 0～40 0℃范围内对设备、管线和阀门的腐蚀特点、腐蚀机理以及针对高温环烷酸腐蚀所采取的防护措施。通过试验和理论分析 ,提出了应用新材料和新工艺解决减粘后高温渣油系统的腐蚀及低温露点腐蚀的建议     

车间调度下流水线制造系统的仿真研究

在车间调度的基础上，采用事件调度法仿真策略，对流水线制造系统的仿真进行研究。     

大庆油田杏1-3区三次加密试验区剩余油分布研究

通过对试验区近年完钻的检查井各单砂层水淹状况及其影响因素的分析。利用神经网络模式识别方法建立起单层剩余油识别模型，在此基础上对三次加密试验区各小层剩余油分布进行研究，总结出各类油层剩余油分布特征及成因类型，并分析了试验区剩余油潜力分布，从而为三次加密布井及射孔方案编制提供了可靠的依据。     

储层石蜡沉积预测技术研究与应用

在油田开发过程中 ,由于油藏温度、压力等条件的变化 ,高含蜡原油在近井带容易产生石蜡沉积 ,堵塞地层孔隙或裂缝 ,严重影响油田开采 ,尤其对于低渗油田 ,伤害特别严重。文中应用理想溶液理论、质量守恒和能量守恒等基本原理 ,建立更符合油田实际情况的油藏中石蜡沉积预测数学模型 ,开发一套方便实用的油藏中石蜡沉积预测软件系统FPOS1 0。在此基础上 ,应用室内实验数据和现场数据对吉林新民油田油井石蜡沉积情况进行预测和现场拟合 ,确定新民油田临界石蜡沉积半径为 2 5m ,快速、准确地为现场清防蜡措施提供理论依据。     

A randomized voltage vector switching scheme for three-level powerinverters

In this paper, a feasibility study of a randomized space vector switching scheme for three-level inverters is reported. Based on the traditional space vector concept for pulse width modulation (PWM) inverters, the sequence of the space vector is randomized in this scheme. The overall vector, resulting from the randomization, is mathematically identical to that of the traditional space vector. It has been found that the randomized scheme can effectively spread the switching noise over a wide frequency range and at the same time keep the steady-state link capacitor voltage balanced. The proposed scheme has been implemented in real time in a digital controller and its features have been experimentally confirmed     

Thermal—Mechanical Fatigue Behavior and Life Analysis of Cast Ni—base Superalloy K417

In-phase(IP) and out-of-phase(OP)thermal-mechanical fatigue(TMF) behavior of cast Ni-base superalloy K417 was studied.All experiments were carried out under total strain control with temperature cycling between 400-850℃.Both in-phase and out-of-phase TMF specimens exhibited cyclic hardening followed by cyclic softening at the minimum temperature.Besides,they cyclically hardened in the early stage of life followed by cyclic softening at the minimum temperature.Besides,they cyclically hardened in the early stage of life followed by cyclic softening at the maximum temperature.OP TMF life was longer than of IP TMF.Various damage mechanisms operating in different controlled strain ranges and phasing were discussed.A few life prediction methods for isothermal fatigue were used to handle TMF fatigue and their applicability to superalloy K417 was evaluated.The SEM analysis of the fracture surface showed that transgranular fracture was the principal cracking mode for both IP and OP TMF.Oxidation was the main damage mechanism in causing shorter fatigue life for IP TMF compared with OP TMF.     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

热力除氧器运行特性实验研究

在热力除氧器实验装置上，对研制的新型除氧器进行了稳态运行特性和动态运行特性实验，得到了除氧器的各种运行特性曲线。研究结果表明，由于对喷嘴和填料进行改进，建立起有利于除氧的传热传质条件，使所研制的除氧器具有良好的稳态及动态运行特性，除氧效果优良。