手工水饺定量给馅机的设计

手工水饺定量给馅机解决了包制手工水饺的定量给馅问题，保持每个水饺的重量一致稳定。该机采用柱塞泵给馅，气动传动，自动化，高效率，适合工业化生产手工水饺使用。     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Polyetherimide substrates for future high density optical data storage

Polyetherimide (PEI) substrate for next‐generation high density optical data storage is fabricated and characterized. Cover‐layer incident or first‐surface recording configurations do not require optical properties of the substrate, which are the prerequisite conditions for the conventional material of polycarbonate (PC). Instead of the optical properties, good mechanical properties with a sufficient transcribability are required. Even though PEI has higher glass transition temperature than that of PC, a microscopic transcribability of PEI is comparable with PC by laminating a thermal insulation layer on the backside of a stamper to retard the heat flow. A macroscopic warpage of PEI substrate is smaller than that of PC substrates, which reduces tilt and servo burden. The lowest critical speed coupled with the flutter of PEI substrate is larger than that of PC substrate because of the mechanical properties of PEI. POLYM. ENG. SCI., 48:97–101, 2008. © 2007 Society of Plastics Engineers     

基于非均匀星座的改进ARQ方案及其性能分析

本文针对调制阶数大于4的MPSK和MQAM调制，在重传中采用非均匀星座图和符号比特重新排序，提出了一种改进的ARQ方案。通过对AWGN信道下ARQ方案进行理论分析和数值仿真，表明基于非均匀星座的新方案在信道条件较差时能有效地提高重要比特的可靠性，若重传中结合符号比特重排和分组合并，则可使接收端解调合并后的比特可靠性趋于均匀且总体得到提高，从而有效地减少重传次数，提高系统的吞吐率。由于本文所提方案并不改变调制解调规则和数据分组长度，故容易实现和控制。     

High-Tc dc-SQUID magnetometer and its application in eddy current non-destructive evaluation

We have fabricated and tested a high-T_c dc-SQUID magnetometer patterned on a YBCO thin film deposited on a SrTiO₃ bicrystal substrate. The measurement of noise spectrum at 77 K showed that the magnetometer has a white noise of 333 fT/Hz^1/2 without superconducting shield, corresponding to a flux sensitivity of 14.5 μΦ₀/Hz^1/2. We constructed a test system for eddy current non-destructive evaluation of conducting aluminum plates by using the magnetometer. Flaws over 10 mm below the surface can be clearly identified. By mapping the magnetic field distribution, we can locate the flaw position. The signals caused by flaw were expanded due to the use of double-D type driving coil with a wider central slit. The experimental results confirmed that this test system could operate in a magnetic unshielded environment.     

Verification of submodeling technique in thermomechanical reliability assessment of flip-chip package assembly

In this paper we verified the submodeling technique applied in the thermomechanical reliability assessment of a flip-chip BGA under accelerated thermal cycling test conditions. Since the steady-state creep model was implemented for the solder bump to better represent its realistic mechanical behavior, submodeling procedures developed specifically for path-dependent thermomechanical problems were considered. A detailed global model for the flip-chip BGA was built up to verify submodeling solutions. This model also served as a benchmark to examine solution discrepancies caused by different simplifications of the global model.     

国外尾矿坝安全与环境研究综述

安全与环境一直是国外尾矿坝研究的重点。笔者综述了自1990年以来国外涉及尾矿坝安全与环境方面有代表性的文献 ,内容包括尾矿坝溃坝、溃坝理论研究、安全管理、环境污染、污染监测、污染治理、污染理论研究及生态复垦 ,这些对提高我国尾矿坝管理、工程技术水平都有较好的参考价值     

Developing Cost Response Models for Company-Level Cost Flow Forecasting of Project-Based Corporations

The difficulty in applying the standard curve (S-curve) and cost-schedule integration (CSI) techniques for company-level cost flow forecasting in a project-based industry is the prerequisite of forecasting future unknown individual projects and contract classifications. By analyzing cost flows at the company level through a pool of macroeconomic and internal financial data, this paper proposes an innovative approach to firm-specific model estimation. First, a series of data transformations introduce linear relationships between cost, macroeconomic, and internal financial variables. Second, multivariate regression analysis is employed for initial model building. Third, for the purposes of model restructuring, a subsequent application of Yule–Walker estimates and incomplete principal component analysis is used. This paper uses a sample of four project-based construction firms to demonstrate model performance. Using this methodology, mean absolute percentage error (MAPE) values of the forecasting models range from 0.27 to 0.60%. As such, the transformed cost, macroeconomic, internal financial data could strongly predict company-level cost flow forecasting. While converting the predicted cumulative cost data to periodic cost flows, the MAPE values were augmented, ranging from 7.04 to 17.55%, thus, requiring future research.