基于分形插值的改进趋势面拟合法在地面沉降中的应用

针对区域地面沉降监测点数量有限、分布不均的情况,一般采用空间插值的手段建立表面拟合模型来解决。基于分形插值,采用随机选择迭代函数的思想对传统的趋势面拟合法作出改进,改进后拟合优度系数提高0.03,达到0.995,且改进前后的拟合结果符合显著性检验的要求。实验结果表明:改进前后趋势面拟合法拟合结果满足地面沉降监测的精度要求,改进后方法的拟合优度更高,对现实地面沉降量变化的描绘更加真实,可为沉降灾害评价工作提供更准确的依据。     

服役后20号钢在低温下的力学性能研究

分析了20号无缝钢管的室温和低温力学性能,结合显微组织观察、晶粒度统计和断口分析,发现低温低应力工况下服役后20号无缝钢管的力学性能完全符合冷库用液氨管道的使用要求。     

多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。     

共享交通的时空轨迹检索与群体发现

为解决共享交通下的共乘用户群体发现效率低、准确率不高问题，依据R-树原理建立GeoOD-Tree索引，并在此基础上提出以最大化共乘率为目标的群体发现策略。首先，对原始时空轨迹数据进行特征提取与标定处理，挖掘有效出行起讫点（OD）轨迹；其次，针对用户起讫点轨迹的特征，建立GeoOD-Tree索引进行有效的存储管理；最后，给出以最大化共乘行程为目标的群体发现模型，并运用K最近邻（KNN）查询对搜索空间剪枝压缩，提高群体发现效率。采用西安市近12000辆出租车营运轨迹数据，选取动态时间规整（DTW）等典型算法与所提算法在查询效率与准确率上进行性能对比分析。与DTW算法相比，所提算法的准确率提高了10.12%，查询效率提高了约15倍。实验结果表明提出的群体发现策略能有效提高共乘用户群体发现的准确率和效率，可有效提升共乘出行方式的出行率。     

Isolated hepatic tuberculosis mimicking liver tumors in a dialysis patient

Cases of isolated hepatic tuberculosis (TB) are rare. The diagnosis is often delayed or missed because of nonspecific symptoms and laboratory findings. Besides, the disease is extremely rare even in a country where TB is an alarming public health problem. This report demonstrates the difficulty in correctly diagnosing local hepatic TB. We report the case of a 62‐year‐old male patient with end‐stage renal disease treated with hemodialysis, who developed 2 months of abdominal distension and general anorexia, with hyperechoic hepatic lesions on ultrasound. Computed tomography suspected multiple liver tumors. The liver biopsy finally led to the diagnosis of TB of the liver without other involvements. We conclude that isolated hepatic TB is one of the rare forms of extrapulmonary TB in dialysis patients. A greater awareness of this rare clinical entity may prevent needless surgical interventions.     

Polyethylene oxide-polypropylene oxide -polyethylene oxide derived porous carbon materials with different molecular weights as ORR catalyst in alkaline electrolytes

Polyethylene oxide (PEO)-polypropylene oxide (PPO)-polyethylene oxide block copolymer having different molecular weights are used as precursors of carbon materials to prepare Hollow -Derivatives carbon material as an electrocatalyst through block copolymer self-assembly. The composition and microstructure of the prepared catalysts are shown by Raman spectroscopy, X-ray diffraction (XRD), Test of nitrogen adsorption and desorption curves, High resolution transmission electron microscopy (HR-TEM) and scanning electron microscopy (HR-SEM). Oxygen was passed into alkaline electrolyte solution until the solution reached saturation state. With molecular weight increasing, the obtained sample gradually changed from block to hollow and spherical. When the molecular weight was 12600 g mol^?1, the evenly hollow carbon nanocages was acquired (C-12600). In O₂ saturated alkaline electrolyte (0.1 M KOH solution), C-12600's limited current density，half-wave potential and initial potential are 5.23 mA cm^?2@0.4 V, 0.72 V and 0.81 V, respectively. And most important is that half-wave potential and onset potential have barely change after 2000 cycles of cyclic voltammetry. As a result, the porous carbon materials exhibited excellent electrocatalytic activity while maintaining high stability in alkaline KOH solution.     

A novel temperature-tolerant foamed resin for enhanced oil recovery

The synthesis and performance of a novel temperature-tolerant foamed resin for enhanced oil recovery were investigated using various methods, including infrared, NMR, scanning electron microscopy (SEM), and displacement experiments. Polycondensation of furfuryl alcohol prepolymers was confirmed by the infrared and NMR results. The poor temperature tolerance of furfuryl alcohol prepolymers after gelation at high temperatures is mainly due to the fracture of furan rings. The addition of ester additives is an effective method of increasing the temperature tolerance of the prepared foamed resins and can effectively reduce the weight-loss rate of the polycondensation products. The SEM results show that the skeleton structure of the foamed resin remains intact after high-temperature treatment. Thus, the novel plugging agent system has excellent thermal stability and still has a high strength (>0.8 MPa) after high-temperature aging treatment for 40 days, giving the prepared foamed resin a good plugging performance (plugging rate > 91%) at 250 °C. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47161.