Determination of molecular weight distributions of tert-octylphenol ethoxylate surfactant polymers by laser desorption Fourier transform ion cyclotron resonance mass spectrometry and high-performance liquid chromatography

Triton polymers are commercial surfactants whose molecular weight distributions are conventionally determined by means of high-performance liquid chromatography (HPLC). However, in the case of the important octylphenol ethoxylates [p-C8H17-C6H4-O-(CH2CH2O)n-H], HPLC cannot resolve individual oligomers of high molecular weight Triton surfactants (e.g., greater than 2000 u or so; u = unified atomic mass unit). In this paper, we show that laser desorption Fourier transform ion cyclotron resonance mass spectrometry (LD/FT/ICR/MS) provides a simple and accurate measure of such Triton surfactant molecular weight distributions up to at least 3500 u, based on a single-shot laser pulse measurement of a few seconds duration. Comparison of LD/FT/ICR/MS and HPLC molecular weight distributions of low molecular weight surfactants shows that laser desorption/ionization produces minimal fragmentation and thus offers an accurate measure of the relative abundances of the neutral oligomers, without the need for prior chromatographic separation of the components. Moreover, for all Triton polymer molecular weight distributions (700-3000 u), LD/FT/ICR/MS provides much more highly resolved profiles of oligomer relative abundances. Finally, LD/FT/ICR/MS reveals the presence of poly(ethylene oxide) side products of the polymerization process, which are not observed by HPLC with conventional ultraviolet absorption detection.     

佛山市中心组团桥梁群对河道影响的数值分析

在不同频率流量和阻水程度条件下,采用一维明渠非恒定流网河数学模型,分析规划中的佛山市桥梁群对区间河道洪季行洪、枯季水环境的影响,计算洪季不同频率洪峰流量下规划桥梁群对区间河道行洪洪水位、分流比的影响,枯季时规划桥梁群对区间河道过流量、分流比的影响,结果表明,利用一维网河数学模型计算佛山市中心组团规划桥梁群对区间河道断面平均水位、流量和流速的影响,结果有足够的数值精度,是可信的。     

锂离子电池有机电解液成膜添加剂的研究现状

文章综述了锂离子电池有机电解液成膜添加剂的作用原理，具体介绍了CO2、SO2、VC化合物、卤化物、有机铜盐以及马来酐等添加剂的研究现状。     

上海外环隧道水下最终接头的施工技术

沉管隧道采用水下最终接头,可以大大缩短工期和减少成本,但施工难度较大,而且有一定风险。文章以上海外环隧道工程为例,对沉管隧道水下最终接头的施工工艺中管段轴线精度控制、安装保护罩、间隙间的安全排水和混凝土施工等四大难点进行探讨,并介绍了水密性施工和管内结构施工的具体工艺和步骤。指出其成果对今后类似工程具有较大的参考价值。     

Identify unrepairability to speed-up spare allocation for repairing memories

In this paper, we discuss some strategies for identifying unrepairable memories, and from that to introduce a novel theorem that can make more precise identification. A new algorithm for searching repair solutions is also proposed, which characterizes the rows, and columns of defective memory cells with revised effective coefficients. We have simulated it on many generated example maps, and compared it with the previous algorithms to verify its efficiency. It's combined with those arranged strategies of judging unrepairability to generate a complete flow. The complete algorithm has also been run on many examples with various memory sizes, defect numbers, and distribution types. The simulation results further show that identifying unrepairability in advance can help the reconfiguration procedure run much faster than searching solutions directly.     

基体温度对磁控溅射沉积ZAO薄膜性能的影响

利用中频交流磁控溅射方法 ,采用氧化锌铝陶瓷靶材 [w(ZnO) =98%、w(Al2 O3 ) =2 % ]制备了ZAO(ZnO∶Al)薄膜 ,观察了基体温度对ZAO薄膜的晶体结构、电学和光学性能的影响 ,采用X射线衍射仪对薄膜的结构进行了分析 ,采用光学分度计和电阻测试仪测量了薄膜的光学、电学特性 ,采用霍尔测试仪测量了薄膜的载流子浓度和霍尔迁移率。结果表明 :沉积薄膜时的基体温度对薄膜的结构、结晶状况、可见光透射率以及导电性有较大的影响。当基体温度为 2 5 0℃ ,Ar分压为 0 8Pa时 ,薄膜的最低电阻率为 4 6× 10 -4Ω·cm ,方块电阻为 35Ω时 ,可见光 (λ =5 5 0nm)透射率高达 92 0 %。     

绿色再生混凝土利用途径与评定思路

就再生混凝土骨料进行深入系统的研究 ,建立了一套与现行评价天然骨料标准相一致的评定方法 ,具有工程实际意义 ,为将来实际应用作好了基础理论研究     

IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

示踪剂技术在秦家屯油藏开发中的应用

秦家屯油田位于松辽盆地南部东南隆起区十屋断陷东北部,属于非均质断块层状油藏,通过示踪剂监测技术可以了解区块内井间连通情况,判断油井见水、来水方向及油层水驱动用程度,结合油藏静态资料研究,指导油田开发,改善开发效果,达到了稳产的目的。