双波长稳频CO_2激光模糊控制系统的建模与优化

报导一种模糊逻辑控制系统的建模与优化方法。以此方法设计的模糊逻辑控制器，用于双波长稳频ＣＯ２激光器的控制得到令人满意的结果。     

Storage performance-metrics and benchmarks

The metrics and benchmarks used in storage performance evaluation are discussed. The technology trends taking place in storage systems, such as disk and tape evolution, disk arrays, and solid-state disks, are highlighted. The current popular I/O benchmarks are then described, reviewed, and run on three systems: a DECstation 5000/200 running the Sprite Operating System, a SPARCstation 1+ running SunOS, and an HP Series 700 (Model 730) running HP-UX. Two approaches to storage benchmarks-LADDIS and a self-scaling benchmark with predicted performance-are also described     

Clinical study in epidural injection with lappaconitine compound for post-operative analgesia

In this study, the effect and side-effect of epidural injection with lappaconitine compound for post-operative analgesia was observed. One hundred and twenty patients were randomly divided into 4 groups. Lappaconitine compound (LB) consisted of 12 mg of lappaconitine and 22.5 mg of bupivacaine, was given to group A (the group of observation), and lappaconitine 12 mg, bupivacaine 22.5 mg and morphine 2 mg to group B, C and D respectively for control. All were given by epidural injection with single blind method during post-operative pain of incision operation. Result showed that the initiating of analgesia was quicker in group A and C than that in group B and D, and the efficacy was group D > A > C > B. There was significant difference between group A and B in the above two parameters, P < 0.01 and P < 0.05. The analgisia maintenence time of single injection was D > A > B > C, that of group D was significantly longer than that of group A (P < 0.01). It indicated that the epidural injection with LB was more rapid and potent than that with lappaconitine alone in post-operative analgesia, and the former had no side-effect, it was safer than morphine.     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

Normal-incidence InAs self-assembled quantum-dot infrared photodetectors with a high detectivity

An InAs/AlGaAs quantum-dot infrared photodetector based on bound-to-bound intraband transitions in undoped InAs quantum dots is reported. AlGaAs blocking layers were employed to achieve low dark current. The photoresponse peaked at 6.2 /spl mu/m. At 77 K and -0.7 V bias, the responsivity was 14 mA/W and the detectivity, D*, was 10/sup 10/ cm/spl middot/Hz/sup 1/2//W.     

Improved Yen-Joye's authenticated multiple-key agreement protocol

An authenticated multiple-key agreement protocol is proposed. The protocol is not only secure against the unknown-key attack but also more efficient than other protocols.     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

Coplanar waveguide-fed uniplanar bow-tie antenna

The design of coplanar waveguide (CPW)-fed bow-tie antenna for the 2.4-GHz ISM band is described. A coplanar waveguide-to-coplanar strips (CPW-to-CPS) balun is used to obtain the balanced feed line for the printed bow-tie. An analysis method based on the mixed potential integral equation method is used to characterize the input characteristics of the bow-tie antenna. The numerical results obtained are in good agreement with the experimental data. Through experiments with bow-tie antennas of various extended angles, the bow-tie antenna with a 90° extended angle exhibits the widest bandwidth in the desired frequency band which has a bandwidth of 17% for a VSWR <1.5:1