A 3D analysis of the joint torques developed during driver's ingress–egress motion

Providing an easy ingress–egress (I/E) movement remains a challenge for car designers. I/E has been largely studied in kinematics, but not in dynamics. This study proposes: (1) to evaluate and describe the motor torques developed in the lower limbs and lumbar joints during I/E motions and (2) to analyse the influence of the car geometry and subject anthropometry. An experiment was performed to observe 15 subjects of three anthropometrical groups getting in and out of a car mock-up simulating three different vehicle configurations. Motor torques were extracted using an inverse dynamics analysis. Both ingress and egress motions were primarily characterised by large torques. Overall, the taller a subject and the lower the seat of the vehicle were, the larger the peak torques were. Moreover, peak torques were higher for egress than ingress. These results are discussed in regard to the current knowledge on I/E ergonomics.     

Free fatty acid inhibition of the insulin induction of glucose-6-phosphate dehydrogenase in rat hepatocyte monolayers

Rat hepatocytes in monolayer culture were utilized to determine if the decrease in glucose-6-phosphate dehydrogenase (G6PD) activity resulting from the ingestion of fat can be mimicked by the addition of fatty acids to a chemically, hormonally defined medium. G6PD activity in cultured hepatocytes was induced several-fold by insulin. Dexamethasone or T3 did not amplify the insulin induction of G6PD. Glucose alone increased G6PD activity in cultured hepatocytes from fasted donors by nearly 500%. Insulin in combination with glucose induced G6PD an additional two-fold. The increase in G6PD activity caused by glucose was greater in hepatocytes isolated from 72 hr-fasted rats as compared to fed donor rats. Such a response was reminiscent of the “overshoot” phenomenon in which G6PD activity is induced well above the normal level by fasting-refeeding rats a high glucose diet. Addition of linoleate to the medium resulted in a significant suppression of insulin’s ability to induce G6PD, but linoleate had no effect on the induction of G6PD activity by glucose alone. A shift to the right in the insulin-response curve for the induction of G6PD also was detected for the induction of malic enzyme and acetyl-CoA carboxylase. Arachidonate (0.25 mM) was a significantly more effective inhibitor of the insulin action than linoleate was. Apparently rat hepatocytes in monolayer culture can be utilized as a model to investigate the molecular mechanism by which fatty acids inhibit the production of lipogenic enzymes. In part, this mechanism of fatty acid inhibition involves desensitization of hepatocytes to the lipogenic action of insulin.     

Supported Alumina Members by an in-Situ Sol–Gel Method

Alumina membranes were prepared using a sol–gel process. Thin gel layers were grown onto porous alumina support tubes by using the permeation of water through the tube to control the rate of hydrolysis. Optimum coating conditions were found to be an ASB to 2-propanol volume ratio of 1:25, coating times between 10 and 15 s, and partial drying times between 2.5 and 3 min, depending on whether the water was flowing in the tube or stored in the tube. The coatings remained crack-free and adherent when fired to 800°C.     

Lipase PS-catalyzed transesterification of citronellyl butyrate and geranyl caproate: Effect of reaction parameters

Pseudomonas sp. lipase PS was immobilized by adsorption and tested for its ability to catalyze the synthesis of citronellyl butyrate and geranyl caproate by transesterification in n-hexane. The reaction parameters investigated were: enzyme load, effect of substrate concentration, added water, temperature, time course, organic solvent, pH memory, and enzyme reuse. Yields as high as 96 and 99% were obtained for citronellyl butyrate and geranyl caproate, respectively, with 300 units (approx. 15% w/w of reactants) of lipase PS. Increasing amounts of terpene alcohol inhibited lipase activity, while excess acyl donor (triacylglycerol) concentration enhanced ester production. Optimal yields were obtained at temperatures from 30–50°C after 24-h incubation time. Yields of 90 and 99% were obtained for citronellyl and geranyl esters, respectively, with 2% added water. Solvents with log P values ≥ 2.5 showed the highest conversion yields. pH 7 and 6–8 seemed to be ideal for citronellyl butyrate and geraniol caproate, respectively. The lipase remained active after reusing 12 times.     

Synthesis of Biodiesel from Canola Oil Using Heterogeneous Base Catalyst

A series of alkali metal (Li, Na, K) promoted alkali earth oxides (CaO, BaO, MgO), as well as K₂CO₃ supported on alumina (Al₂O₃), were prepared and used as catalysts for transesterification of canola oil with methanol. Four catalysts such as K₂CO₃/Al₂O₃ and alkali metal (Li, Na, K) promoted BaO were effective for transesterification with >85 wt% of methyl esters. ICP-MS analysis revealed that leaching of barium in ester phase was too high (~1,000 ppm) when BaO based catalysts were used. As barium is highly toxic, these catalysts were not used further for transesterification of canola oil. Optimization of reaction conditions such as molar ratio of alcohol to oil (6:1–12:1), reaction temperature (40–60 °C) and catalyst loading (1–3 wt%) was performed for most efficient and environmentally friendly K₂CO₃/Al₂O₃ catalyst to maximize ester yield using response surface methodology (RSM). The RSM suggested that a molar ratio of alcohol to oil 11.48:1, a reaction temperature of 60 °C, and catalyst loading 3.16 wt% were optimum for the production of ester from canola oil. The predicted value of ester yield was 96.3 wt% in 2 h, which was in agreement with the experimental results within 1.28%.     

A biomarker of n−3 compliance in patients taking fish oil for rheumatoid arthritis

Dietary fish oil supplements have been shown to have benefits in rheumatoid arthritis (RA), other inflammatory diseases, and in cardiovascular disease. As with any medical advice, variability will exist with regard to adherence and consequent biochemical or pharmacophysiologic effects. The aim was to explore the utility of plasma phospholipid EPA as a measure of n−3 PUFA intake and response to standardized therapeutic advice given in an outpatient or office practice setting, to increase dietary n−3 PUFA, including a fish oil supplement. Patients with early RA were given verbal and written advice to alter their dietary n−3 PUFA intake, including ingestion of 20 mL of bottled fish oil on juice daily. The advice included instructions to increase n−3 PUFA and to avoid foods rich in n−6 PUFA. Every 3 mon, blood samples were obtained for analysis of plasma phospholipid FA. Plasma phospholipid EPA was used as the primary index of n−3 PUFA intake. A diverse response was seen, with about one-third of patients achieving a substantial elevation of plasma phospholipid EPA over the 12-mon study period. A third had little change, with the remainder achieving intermediate levels. Data obtained longitudinally from individual patients indicated that substantial elevations of EPA (>5% total plasma phospholipid FA) could be maintained for more than 3 yr. Plasma phospholipid EPA is a convenient measure of adherence to advice to take a dietary n−3 PUFA-rich fish oil supplement. This measure may prove a useful adjunct to intention to treat analyses in determining the effect of dietary fish oil supplements on long-term outcomes in arthritis and other chronic inflammatory diseases. It may also provide a guide to the effectiveness of therapeutic and preventive messages designed to increase n−3 PUFA intake.     

Integration Concepts for the Fabrication of LTCC Structures

At the Keck Smart Materials Integration Laboratory at Penn State University, low-temperature co-fired ceramic (LTCC) material systems have been used to fabricate a number of devices for a variety of applications. This article presents an overview of the integration of the concepts and materials that we have used to achieve miniaturization and unique device function. Examples of microwave filters, metamaterial antennas, and a dielectrophoretic cell sorter will be presented, with emphasis on device modeling and design, prototype construction methods, and test results.