碳氮共渗提高空心圆柱滚子轴承寿命的研究

通过GCr15钢碳氮共渗,在表层获得大量的残余奥氏体。磨损中,马氏体组织剥落,残余奥氏体则成小岛状,进而在表面迁移发生形变诱发马氏体相变,使耐磨性得以提高。同时,共渗在空心滚子内表面造成的压应力对改善弯曲疲劳性能有利。     

整锻支承辊锻造新工艺应用研究

本文介绍了第一重型机械集团公司分别用FM法和KD法,以及两种锻造法联合生产70Cr3Mo钢整锻大型支承辊的工艺及生产经验。使用这些工艺能实现轧辊内部良好压实,减少锻造火次,提高锻造生产率。     

稀盐酸中锰结核还原浸出溶液净化除铁

针对酸性氯化物中黄铁矿还原浸出锰结核的溶液成分特点，选择黄钠铁矾法进行了沉淀分离铁的研究。结果表明温度和晶种以及溶液ｐＨ值是影响铁矾沉淀的重要因素。在ｐＨ２．０左右，溶液温度高于９０℃，足量晶种加入的情形下，１５０ｍｉｎ后可将溶液中的铁含量降至０．１ｇ／Ｌ。沉矾过程的表观活化能为９４．６６ｋＪ／ｍｏｌ。黄铁矿氧化生成的硫酸根随铁一同沉淀，从而消除了ＳＯ２－４在氯化物体系中的积累。     

液压气动缸筒用高精度冷拔钢管生产的回顾与展望

介绍了近年来我国液压气动缸筒用高精度冷拔钢管生产的进展及其现状，分析了影响产品尺寸精度的因素，提出了改进措施，指出了发展方向。     

模糊控制在半固态浆料制备装置中的应用

介绍了低转速输送管半固态浆料制备装置的原理和组成，采用模糊控制技术改进了该装置的温度控制系统，并详细介绍了该控制系统的总体设计及软硬件方案。试验证明，模糊控制技术的应用提高了该装置的温度控制效果，实现了良好稳定的铝金属半固态浆料微观组织控制作用。     

等离子喷涂纳米Al2O3-13%TiO2涂层组织与性能

采用大气等离子喷涂方法制备了纳米结构Al2O3-13%TiO2(质量分数,下同)涂层,进行了SRV滑动磨损试验,通过扫描电镜对涂层的断口显微组织及磨损表面形貌进行了观察,并测定了涂层的显微硬度.结果表明,该纳米涂层具有独特的显微组织结构特征,层片间具有冶金结合特征的界面较多,界面结合得到明显改善,其显微硬度明显高于微米涂层,具有优良的耐磨性能,其磨损面积仅为常规微米涂层的1/5,界面结合改善是耐磨性提高的主要原因.     

Preparation and properties of nanosize MnZn ferrite from δ-FeOOH

Ferrous ion was transformed into feroxyhyte (δ-FeOOH) by oxidation. Then, manganese sulfate and zinc sulfate in some ratio were added to the feroxyhyte solution. The co-precipitation was boiling reflux conditions sometime under constant stirring. The nanosize MnZn ferrite powder was formed. The mechanism of preparation of the nanosize MnZn ferrite was discussed, and the formation of feroxyhyte which was playing a key role during the process was mentioned. The properties of powder was tested by means of X-ray diffraction, transmission electron microscopy and vibrating sample magnetometer. The results show that the samples of spherical particles about 20 nm, which have characteristics of ferrimagnetism, has larger saturation magnetization, but the remanent magnetization and coercivity are comparatively smaller. The spinel MnZn ferrite nanosize powder was successfully prepared from δ-FeOOH at low temperature, with low-carbon steel and peroxide as main material.     

圆柱体相贯线上的圆角表示方法

在机械设计中，圆柱体相贯线上的圆角表示方法是CAD和计算机辅助设计中的难题，所有的CAD／CAM软件都没有这一功能，多数使用者采用的是各种近似方法。本文介绍了严密精确的设计和几何造型方法，可用于大型铸锻件和重型机械的CAD和计算机辅助设计。     

Influence of the stress,strain, and temperature on the surface roughness of an AlSl 52100 steel due to an orthogonal cut

In recent years, the finite element method (FEM) has become the main tool for simulating the metal cutting process because research based on trial and error is time consuming and requires high investment. Early studies were done by different investigators. In this research AISI 52100, hardened steel (62 HRC) was selected for an orthogonal machining process as well as metal cutting simulation using the software DEFORM-2D. This software is based on a forging process and has been adapted to an orthogonal machining process. The results of simulated cutting forces were compared with experimental cutting force data to validate the orthogonal cut simulation. Also, the surface roughness was measured, and the influence of the stress, strain, and temperature on the surface roughness was studied.     

过共晶铝硅合金半固态浆料表观粘度研究

通过自制的双筒旋转粘度计对过共晶ZL117合金的表观粘度进行了研究。结果表明,随着保温温度的降低,即固相率的升高,ZL117合金浆料的表观粘度随之增加;随着搅拌电流的增加,其表观粘度先降低,在搅拌电流为14A左右时达到最低,然后增大;随着冷却速度的增大,其表观粘度增大。