溶剂脱沥青组合工艺生产重交通道路沥青

中国石化荆门分公司以江汉-阿曼混合原油和江汉-鲁宁混合原油为原料,分别采用减压蒸馏—丙烷脱沥青和减压蒸馏—添加催化裂化油浆—丙烷脱沥青工艺,生产出符合SH 0522—2000的100号道路沥青。结果表明,江汉-阿曼混合原油减压渣油中掺兑质量分数为30%的催化裂化油浆后,脱油沥青的各项性能均满足AH-70或AH-90重交通道路沥青的要求,而且薄膜烘箱试验表明,试样延度超过标准要求。     

广州清洁燃料汽车发展方向

选择好合适的汽车替代燃料，科学确定一个地区清洁燃料汽车的发展方向，是减少机动车有害尾气排放、控制城市大气环境污染重大而紧迫的课题。国内外汽车清洁燃料的发展规律表明，天然气特别是液化天然气，是汽车替代燃料的最佳选择与发展方向。为此，探讨了随着天然气工业的加快发展，作为广州这样一座已经发展液化石油气汽车并已形成有一定规模的城市，如何适应新形势的需求，科学决策，选择符合国家能源发展政策并适应当地具体实际的汽车清洁燃料路线，寻求顺利实施液化石油气与天然气两种清洁燃料平稳过渡的具体措施。最后提出以下建议：加速LNG加气站和液化天然气汽车（LNGV）相关技术规范的制定；加快实现LNG关键设备，如LNG泵、LNG售气机、车用LNG储罐的国产化步伐，以降低LNGV和加气站的成本；鉴于LNGV改装技术的现状，不提倡对在用车进行改装，而应加大力度，逐步推广单燃料LNG汽车。     

催化精馏合成N-异丙基苯胺

在Joback基团贡献法估算反应的G ibbs函数的基础上,得到了异丙醇与苯胺合成N-异丙基苯胺的平衡常数与反应温度的关系式。研究了回流比、异丙醇与苯胺的摩尔比、塔釜操作温度、苯胺进料口位置距塔顶的距离对异丙醇与苯胺催化精馏合成N-异丙基苯胺的影响,确定了适宜的工艺条件:回流比2.5~3.5、异丙醇与苯胺的摩尔比1.5、塔釜操作温度223℃、苯胺进料口位置距塔顶300~400mm。在优化条件下,苯胺的转化率可达到99%,N-异丙基苯胺的选择性可达到99.5%,N-异丙基苯胺的质量分数可稳定在98.8%以上。     

H型丝光沸石催化剂催化甲苯与叔丁醇的烷基化反应

针对合成对叔丁基甲苯传统工艺中存在的缺点,采用环境友好、可重复利用的H型丝光沸石催化剂(以下简称催化剂)进行了甲苯与叔丁醇的烷基化反应,并用X射线衍射和氨程序升温脱附等方法对不同焙烧温度下得到的催化剂的物相结构和酸性质进行了表征,研究了各种反应条件对催化剂的催化性能的影响。实验结果发现,在适宜的操作条件下,即催化剂的焙烧温度823K、反应温度180℃、反应时间3h、初始压力1.0MPa、原料与催化剂的质量比为8、叔丁醇与甲苯的摩尔比为4、溶剂环己烷与甲苯的摩尔比为5时,甲苯转化率达42.73%,叔丁基甲苯的选择性为96.30%,对叔丁基甲苯的选择性为80.37%。     

Dispersion-tolerant 10-gb/s duobinary system employing heterodyne detection and MLSE

We experimentally demonstrate a 10.7-Gb/s duobinary transmission system operating over a chromatic-dispersion range of /spl sim/12 000 ps/nm. Heterodyne detection and maximum-likelihood sequence estimation are employed to achieve this result.     

A New Hand-Held Microsystem Architecture for Biological Analysis

This paper presents a hand-held microsystem based on new fully integrated magnetoresistive biochips for biomolecular recognition (DNA hybridization, antibody antigen interaction, etc.). Magnetoresistive chip surfaces are chemically treated, enabling the immobilization of probe biomolecules such as DNA or antibodies. Fluid handling is also integrated in the biochip. The proposed microsystem not only integrates the biochip, which is an array of 16times16 magnetoresistive sensors, but it also provides all the electronic circuitry for addressing and reading out each transducer. The proposed architecture and circuits were specifically designed for achieving a compact, programmable and portable microsystem. The microsystem also integrates a hand-held analyzer connected through a wireless channel. A prototype of the system was already developed and detection of magnetic nanoparticles was obtained. This indicates that the system may be used for magnetic label based bioassays     

An optically clocked transistor array with dual serial-to-parallel and parallel-to-serial conversion capability for optical label swapping

We propose an optically clocked transistor array optoelectronic integrated circuit (OEIC) for both serial-to-parallel and parallel-to-serial conversion (demux/mux), enabling an interface between high-speed asynchronous burst optical labels and CMOS circuitry for optical label swapping. Dual functionality of the OEIC reduces size, power, and cost of the optical label swapper. The capability for greater than 20-Gb/s conversion operation is demonstrated.     

Knowledge-based control and case-based diagnosis based upon empirical knowledge and fuzzy logic for the SBR plant.

Because biological wastewater treatment plants (WWTPs) involve a long time-delay and various disturbances, in general, skilled operators manually control the plant based on empirical knowledge. And operators usually diagnose the plant using similar cases experienced in the past. For the effective management of the plant, system automation has to be accomplished based upon operating recipes. This paper introduces automatic control and diagnosis based upon the operator's knowledge. Fuzzy logic was employed to design this knowledge-based controller because fuzzy logic can convert the linguistic information to rules. The controller can manage the influent and external carbon in considering the loading rate. The input of the controller is not the loading rate but the dissolved oxygen (DO) lag-time, which has a strong relation to the loading rate. This approach can replace an expensive sensor, which measures the loading rate and ammonia concentration in the reactor, with a cheaper DO sensor. The proposed controller can assure optimal operation and prevent the over-feeding problem. Case-based diagnosis was achieved by the analysis of profile patterns collected from the past. A new test profile was diagnosed by comparing it with template patterns containing normal and abnormal cases. The proposed control and diagnostic system will guarantee the effective and stable operation of WWTPs.     

Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.