The toughness of copolymers of polypropylene

A series of fracture mechanics tests of a set of random and impact copolymers of polypropylene, in which the ethylene content was varied, is described. The plane strain toughness is found to change from the homopolymer value, but thereafter to be independent of ethylene content. The yield stress of the impact copolymers decreases markedly with ethylene content, while that for random copolymers increases only slightly. This is reflected in toughness values in tension. A comparison with the behavior of other rubber-modified materials is made and it is concluded that crazing is an important mechanism in polypropylene and is perhaps more rate and temperature sensitive than in acrylonitrile-butadiene-styrene (ABS).     

Nucleation and growth of anodic oxide films on bismuth—I. Cyclic voltammetry

The early stages in the formation of a continuous anodic layer of bismuth oxide on a solid bismuth electrode, in the pH range 5–14, were studied. The oxide covered the surface by the simultaneous thickening and spreading of patches. The metal surface was classified into two different areas with different overvoltage for oxide nucleation. The ratio of the two areas varied according to the history of the surface.The thickening of the newly formed layer (final thickness ～20 nm) followed the high-field growth law i = $\text{A}$exp(B$\text{E}$) where $\text{E}$ is the field in the oxide layer, with B = (2.0 ± 0.5) × 10^?6 V^?1 cm. This value of B gives an activation distance for high-field ion transport of 0.2 nm, comparable to the radius of a lattice site and much smaller than that obtained previously, for much thicker films.Dissolution of the film, giving breakdown of the oxide layer and pitting of the metal, occurred for pH<8. The thickness of the anodic film was thus limited to only 4 nm at pH 5.Cathodic reduction of the anodic oxide resulted in a porous metal surface. The current—voltage curve for the reduction often had a complex shape, which was related to the morphology of the original anodic layer.     

Chemical nature of a supercritical-gas extract of coal at 350 °C

A novel supercritical-gas (toluene) extract, comprising 17.0% of a low-rank coal, was separated by a combination of solvent fractionation and both silica-gel and gel-permeation chromatography. The average structure of the soluble fractions, together amounting to 85% of the extract, was investigated by a variety of spectroscopic methods, including high-resolution ¹H nuclear magnetic resonance, proton-decoupled pulse Fourier transform ¹³C magnetic resonance, infrared and low-ionizing-voltage mass spectrometry. Analyses were also made by gas chromatography. The results for the low-oxygen fractions are consistent with a generally open-chain polynuclear aromatic average structure with about 33% of the available sites carrying alkyl substituents. The most common of these is methyl, but there are also substantial numbers of longer-chain alkyls, some branched, and naphthenic groups. The fractions rich in oxygen also have similar structure but for the presence of phenolic hydroxyl groups, and, as is demonstrated for the first time by ¹³C n.m.r., ether oxygen links. Aliphatic constituents are mainly straight-chain alkanes with some branched-chain and isoprenoid hydrocarbons. These conclusions are discussed in terms of the thermal history of the extract and are compared with other contemporary views on the low-molecular-weight constituents of coal.     

Feeding pure docosahexaenoate or arachidonate decreases plasma triacylglycerol secretion in rats

Essential fatty acid (EFA)-deficient rats were fed highly purified methyl esters of docosahexaenoate (22∶6n−3), arachidonate (20∶4n−6), alpha-linolenate (18∶3n−3) or oleate (18∶1n−9) (100 mg/day, tube fed for 3–10 days), and their plasma triacylglycerol (TG) secretion rates were measured. Secretion rates of TG into plasma were reduced by tube-feeding 22∶6n−3, 20∶4n−6, 18∶3n−3, but not 18∶1n−9, to EFA-deficient rats. A significant reduction occurred after feeding 22∶6n−3 for only three days. Feeding 22∶6n−3 or 18∶3n−3 to EFA-deficient rats for three days also reduced the activities of liver lipogenic enzymes and sharply increased the proportions of 22∶6n−3 and 20∶5n−3 in liver phospholipid fractions. Mechanisms by which these EFA may reduce lipogenesis are discussed.     

Use of surface modified recycled rubber particles for toughening of epoxy polymers

The objective of this research is to investigate the feasibility of using surface treated recycled rubber particles for toughening of epoxy polymers. These particles are obtained through grinding of scrap tires followed by oxidizing the surface of the particles in a reactive gas atmosphere. Surface treated recycled rubber particles with a nominal particle size of approximately 75 μm and a commonly used reactive liquid elastomer, CTBN, have been incorporated in a DGEBA epoxy resin. It has been shown that the recycled rubber particles are not as effective as CTBN in toughening of the epoxy matrix. However, blending of the two modifiers results in a synergistic toughening. Microscopy reveals that, when used alone, recycled rubber particles simply act as large stress concentrators and modestly contribute to toughening via crack deflection and microcracking. In the presence of micron size CTBN particles, which cavitate and induce massive shear yielding in the matrix, however, the recycled particles “stretch” the plastic deformation to distances far from the crack tip. This mechanism causes plastic zone branching and provides an unexpectedly high fracture toughness value. This study, therefore, provides a practical approach for manufacturing engineering polymer blends utilizing the surface modified recycled rubber particles.     

Axial pressure profiles in non-newtonian flow: Part I: Theoretical and experimental considerations

The flow behavior of polymeric fluids in tubes can be determined from measurements of the radial stress profile in the flow direction. This subject, the focus of our research, will be examined in Part II of this communication. Part I describes a research designed to test the accuracy of stress measurement with pressure transducers in a variety of recess mount geometries. No mount geometry errors were detected for the fluids used in this work over a shear rate range of 1 to 2000 sec^?1. Part I also contains a survey of the literature and theoretical considerations pertinent to the entire work.     

Heat transfer

Conclusions Numerous new heat transfer developments have been reported in the last few years. These developments are useful for a better understanding of the basic theory and for developing improved equipment. In many cases both heat and mass transfer occur simultaneously in commercial operations.     

Orientation effects during the flow of short-fibre reinforced thermoplastics

A study has been carried out to investigate molecular orientation in injection moulded bars of short glass fibre reinforced polypropylene and polyethylene. For the range of fibre concentrations encountered commercially, the fibres do not appear to have any direct effect on the matrix orientation. As the fibre concentration increases, however, the matrix orientation becomes dominated by the orientation of the fibres. These effects are interpreted in terms of current ideas of the rheology of polymer melts during injection moulding and the crystallization of polymers at fibre surfaces.     

Rigid polyurethane foams: A model of the foaming process

A model of the manufacture of rigid polyurethane foams by free rising is presented. The extent of cream and rise periods as well as the amount of blowing agent necessary to give the desired foam density are theoretically predicted. The rate of blowing agent evaporation is calculated from an experimental boiling temperature vs. composition curve. Experimental runs were carried out with a formulation consisting of a polymeric isocyanate, a polyether polyol based on sorbitol, a silicone-polyol block-copolymer as surfactant, dibutyltin dilaurate as catalyst, and trichlorofluoromethane as blowing agent. Mixing was performed in situ in the mold using a commercial foaming machine. Experimental results gave a satisfactory agreement with model predictions. A diagram containing all the relevant information may be theoretically built and used for the selection of adequate operating parameters for a given formulation.