Performance engineering and topological design of metro WDM opticalnetworks using computer simulation

This paper demonstrates the use of computer simulation for topological design and performance engineering of transparent wavelength-division multiplexing metropolitan-area networks. Engineering of these networks involves the study of various transport-layer impairments such as amplifier noise, component ripple, chirp/dispersion, optical crosstalk, waveform distortion due to filter concatenation, fiber nonlinearities, and polarization effects. A computer simulation methodology composed of three main simulation steps is derived and implemented. This methodology obtains performance estimations by applying efficient wavelength-domain simulations on the entire network topology, followed by time-/frequency-domain simulations on selected paths of the network and finally Q-budgeting on an identified worst case path. The above technique provides an efficient tool for topological design and network performance engineering. Accurate simulation models are presented for each of the performance impairments, and the computer simulation methodology is used for the design and engineering of a number of actual metro network architectures     

Mode coupling contribution to radiation losses in curvatures for high and low numerical aperture plastic optical fibers

We have studied the optical power losses due to multiple curvatures in polymethylmetacrylate (PMMA) plastic optical fibers (POFs) of different numerical apertures (NAs) and attenuation. The fibers were tested for several configurations in order to assess the influence of different types of curved-to-straight fiber transitions in the amount of power radiation. We found that losses are below the standards for all tested fiber types, and thus, they are a suitable choice for local area network (LAN) applications. In addition, our results revealed the presence of modal interactions as confirmed using an experimental procedure to estimate the mode coupling strength for the same fibers.     

Integrated chaos generators

This paper surveys the different design issues, from mathematical model to silicon, involved in the design of analog CMOS integrated circuits for the generation of chaotic behavior     

Use of weibull statistics to quantify property variability in TiAl alloys

Tensile experiments have been performed on specimens of four different investment-cast TiAl-based alloys with variations in casting conditions. The average ductilities obtained in these experiments vary between approximately 0.8 to 2.0 pct plastic strain to failure in tension. By using the three-parameter form of the Weibull relation, with the 0.2 pct offset yield strength as the minimum failure strength, the resulting variability in the data can be quantified and is found to be similar for those alloys with similar microstructural scale (grain size). Large variations in lamellar volume fraction, segregation, and phase distribution have a minor influence on property variability, compared to changes in the scale of the grain structure caused by either variations in cooling rate during casting or the addition of grain refiners.     

Simulation of the submerged energy nozzle-mold water model system using laser-optical and computational fluid dynamics methods

The present work describes quantitative digital particle image velocimetry measurements of a full-scale water model of a thin slab mold. Different casting speeds and two submerged entry nozzles with one and two outlet ports have been investigated. The flow pattern of the single-port nozzle shows a counterclockwise-rotating double vortex that is nearly steady-state but leads to high stationary surface waves. The flow jets out of the two-port nozzle oscillate and produce a transient flow pattern with low wave amplitudes. The amplitudes for the one-port nozzle show a linear variation with the volumetric flow rate. The experimental results lead to a good interpretation of the flow phenomena and are used to validate steady-state numerical simulations with the commercial program, CFX, on the basis of the Reynolds equations. To describe anisotropic turbulence effects, the Reynolds stress model (RSM) is used for the flat single-port nozzle and the standard k-ɛ model for the mold flow. The calculated mean velocities and wave amplitudes, predicted from pressure distribution at the water surface, are generally in the consensus of the experimental data. An erratum to this article is available at .     

New natural 2-acetoxy fatty acids using chemical ionization and electron impact mass spectrometry

The phospholipids of the spongePolymastia gleneni contain saturated long chain (C_22–30)-acetoxy fatty acids. Their structures were assigned based on chromatographic and spectrometric data as well as comparison with a synthetic sample. The use of capillary gas chromatography combined with chemical ionization and electron impact mass spectrometry was instrumental in the eludication of structures, since only a very small amount of crude lipids was available. Part 10 of “Phospholipids in Marine Organisms.” For Part 9 in this series, see reference 12.     

Flotation machine design: impeller—stator interaction

The separate contributions of impellers and stators to suction are studied by means of interaction models. From these, suction can be predicted when interchangeable components are used in any combination, and in either direction of impeller rotation. Methods are devised by which numerical values of the impeller and stator terms can be simply assigned. The resulting model provides good agreement with experiment. The influence of variability in component geometry is reflected in the model parameters. Possible applications of the model are suggested.     

Effects of seat slope and hip flexion on spinal angles in sitting

Lumbar and thoracic spinal angles of 25 male and 25 female subjects were measured in four sitting postures, with standing angles used as reference. Subjects sat with either 90 deg or 65 deg of hip flexion on either flat or forward-sloping seats. Lumbar kyphosis was greatest when the flat seat/90-deg posture was adopted and least when the sloping seat/65-deg posture was adopted. The opposite was observed for the thoracic angles, and intermediate results were observed for the other two sitting postures. No statistically significant interactions were observed among seat slope, hip flexion, and subject sex. The findings are discussed with reference to the anatomy of sitting and factors influencing pelvic tilt and the implications for the ergonomic design of chairs.