A versatile data acquisition system for time resolved X-ray scattering using gas proportional detectors with delay line readout

A data acquisition system for time resolved X-ray scattering experiments using linear, quadrant or area gas proportional detectors with delay line readout based on commercially available hardware (National Instruments) is described. The system can easily be configured for recording data from point detectors (e.g. photomultipliers and photodiodes) and/or ancillary data only. Applications involving measurements with two different types of time to digital converters illustrate the features and performances of the system.     

Feasibility study of absolute activity measurement with metallic magnetic microcalorimeters

We report on a feasibility study on precise determination of mass-specific activity of low-energy emitting radioisotopes. Conventional methods of activity measurement suffer from source self-absorption and a strong decrease in detection efficiency for low-energy electrons and photons. We propose a new method based on metallic magnetic microcalorimeters with the source embedded in the detector target in a 4π geometry. First results with a ⁵⁵Fe source show that electrons and photons are detected with a detection efficiency close to unity and with little loss of energy for electrons. The aim of this study is to provide standards of activity with very low uncertainties in the framework of radiation metrology.     

On energy arguments applied to the hydrodynamic impact force

The hydrodynamic impact problem is investigated within the framework of potential-flow theory. The vertical load acting on the rigid body is derived based on either momentum or energy conservation, and using the concept of added mass together with a homogeneous Dirichlet condition for the potential on the free surface as usually done to model an impact problem. It is demonstrated that the use of this simplified dynamic free-surface condition, instead of the fully nonlinear one, has a direct influence on the computation of the loads. In particular, the equivalence of momentum and energy analysis is in general not recovered. The situation is then highlighted by performing an asymptotic analysis of the two-dimensional blunt-body asymmetric impact problem. The asymptotic solution is given explicitly and validated through comparisons with experimental results. The energy distribution is then studied. It is shown that the contradiction between momentum and energy analysis can be removed, provided that the flux of energy through the jets is taken into account in the energy balance. If the simplified free-surface condition is indeed valid in the far-field, nonlinear terms must be retained near the body, in the spray-root domains. To leading order, the energy distribution during the gravity-free inertia stage does not depend on the blunt-body shape. The general analysis based on momentum or energy conservation suggests that this result also applies for arbitrary body shape as soon as a homogeneous Dirichlet condition can be applied as a dynamical free-surface boundary condition. In this case, and for a constant vertical impact velocity, half the work performed by the body would seem to be transferred to the fluid as kinetic energy within the spray.     

Wave dynamics on a thin-liquid film falling down a heated wall

The dynamics of a thin liquid film falling down a uniformly heated wall is studied. The model introduced by Kalliadasis et al. [J. Fluid Mech. 475 (2003) 377] for the same problem is revisited and its deficiencies, namely the prediction of a critical Reynolds number with 20% error, cured. For the energy equation a high-order Galerkin projection in terms of polynomial test functions is developed. It is shown that not only does this more refined formulation correct the critical Reynolds number, but it also gives, with an appropriate expansion close to criticality, the long-wave theory. Bifurcation diagrams for permanent solitary waves are constructed and compared with the solution branches obtained from different models. It is shown that, in all cases, the long-wave theory exhibits limit points and branch multiplicity, while the other models predict the continuing existence of solitary waves. Time-dependent computations show that the free surface and interfacial temperature approach a train of coherent structures that resemble the infinite-domain stationary solitary pulses.     

Textural Transitions in a Rotating Slab of 3He-A

The operation of a torsional oscillator for detection, of flow-driven textural transitions in, ³He-A is described. The detection technique, tracking the shift of the resonant frequency of the torsional oscillator, allows us to observe textural changes and the presence of vortices in zero magnetic field. It relies on. the anisotropic superfluid density of ³He-A and its change due to reorientation of the Î-texture caused by counterflow.     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.     

Methodologies for the optimal design of parallel manipulators

In this paper the problem of determining a manipulator design so that its workspace corresponds to a prescribed workspace is considered. Two different strategies, resulting in two different types of optimization problem are considered. The first strategy attempts to obtain a good overall approximation to the prescribed workspace and results in an unconstrained optimization problem. The second strategy entails designing a manipulator so that its workspace fully encloses the prescribed workspace and results in a constrained optimization problem. Two specific formulations of the constrained problem are proposed. The first constrained problem simply aims to fit the manipulator workspace as exactly as possible to the prescribed workspace, while still ensuring that the prescribed workspace is fully enclosed. The second constrained optimization formulation is used to design a manipulator, the workspace of which fully encloses the prescribed workspace, but which is also well‐conditioned throughout the workspace with respect to some performance measure. The particular manipulator used to illustrate and evaluate these formulations is a simple 2‐dof planar parallel manipulator, and the final formulation is also applied to a 3‐dof planar parallel manipulator. Although the manipulators studied here are simple, the objective of this study is to obtain a robust numerical methodology which can be extended to more practical and complex manipulators. Copyright © 2003 John Wiley & Sons, Ltd.     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.