用化学腐蚀制备多孔硅太阳电池减反射膜的研究

采用HF HNO3溶液化学腐蚀 ,在硅片上制备减反射效果优良的多孔硅太阳电池减反射膜 ,借助原子力显微镜 (AFM)和X光电子谱 (XPS)对其表面形貌和成分进行观察 ,发现该膜与电化学阳极腐蚀得到的多孔硅具有相似性 ,其主要成分为非化学配比的硅的氧化物SiOx(X <2 )。采用带积分球的光度分光计 ,测得形成多孔硅减反射膜后 ,硅片表面反射率大大下降 ,,在波长 330～ 80 0nm范围反射率只有 1 5～ 2 9%。研究指出这种强减反射作用 ,与多孔硅具有合适的折射率及其多孔特性的光陷阱作用有关     

低压电、汽两用节能加热锅炉的结构特点

通过对电、汽两用节能加热锅炉的描述,指出该设备具有投资少,无污染,能源转化率高,起停速度快,负荷调节范围大,结构简单,安全性能好并可充分利用电能等特点.     

后压浆技术在杨凌国际会展中心基桩工程中应用效果的分析

本文叙述了杨凌国际会展中心基桩静力载荷试验的试验过程 ;通过对三根灌注桩承载力的试验结果分析 ,认为后压浆技术对提高灌注桩单桩极限承载力有很大作用     

光漂白法制备有机聚合物非线性定向耦合器

研究了用光漂白的方法制备PMMA/DR1聚合物非线性定向耦合器,提出了一种容易的制备方法来得到要求的耦合长度.测量了材料的光学非线性对定向耦合器两臂透过率的影响.实验结果表明由于光学非线性,耦合器的耦合长度随着入射光强度的改变而发生变化.     

汽车稳定杆组织与疲劳性能研究

对28Mn6钢制造的汽车稳定杆，分别采用整体感应加热－整体淬火、连续感应加热淬火两种不同热处理工艺，并进行了台架疲劳寿命试验，采用光学显微镜和扫描电镜，分析了经两种不同热处理工艺处理的稳定杆的金相组织及其早期疲劳断裂的断口形貌，提出，获得细小的高韧性索氏体组织是保证良好疲劳寿命的关键，稳定杆喷丸表面质量，游离铁素体也是影响疲劳性能的重要因素。     

MON--未来城域网的发展方向

阐述了城域光网络(MON)技术的出现背景、定义、技术方案和特点，以及与现有城域基础设施的比较，突出说明了其应用上的竞争优势。最后介绍了MON的现状和前景展望。     

ARAM·ARIES SPM-Lite便携式遥测地震数据采集系统简介

ARAM·ARIES SPM-Lite便携式遥测地震数据采集系统是加拿大GEO-X公司在2002年下半年推出的全新小型便携式地震数据采集系统。该仪器运用了当今最先进的计算机制造技术、网络化技术和微电子技术,除继承了ARAM-ARIES地震数据采集系统所有功能和技术外,它还简化了硬件结构,使体积更小,重量更轻,功能性更强。更加适应地矿、煤田、丛林和山区进行地震勘探。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

N,N''-取代邻苯二胺的合成

通过2-取代苯并咪唑盐的还原开环反应制备了8个N,N′-不同取代的邻苯二胺,并经1HNMR、IR、MS及元素分析表征,其中5个未见文献报道.这是一条由邻苯二胺和羧酸经2.取代苯并咪唑制取该类化合物的简洁合成路线.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry