核磁共振谱的岩石孔喉结构分析

刘堂宴 ,王绍民 ,傅容珊 ,周明顺 ,李艳华 ,罗曼 .核磁共振谱的岩石孔喉结构分析 .石油地球物理勘探 ,2 0 0 3,38(3) :32 8～ 333岩心核磁共振 T2 谱和压汞分析数据均在一定程度上反映了岩石的孔喉结构 ,理论分析表明 ,这两组数据具有相关性。应用岩心核磁共振 T2 谱研究岩石孔喉结构 ,关键是确定 T2 与 Pc的转换系数。但以前的方法在 T2与 Pc 的转换过程中 ,需要涉及某些岩石特性参数 ,实用中有一定困难。本文直接利用岩心核磁共振 T2 谱和压汞分析数据之间的相关性 ,客观地确定 T2 与 Pc之间的转换系数 ,避免了确定岩石特性参数的困难。应用本文方法 ,对 6块岩心的多种核磁共振分析数据进行了对比分析 ,做出了 NMR (Nuclear Magnetic Resonance,简称NMR) T2 毛管力曲线和孔喉半径分布 ,并将这些结果与压汞分析的结果进行了对比。结果表明 ,岩心 NMR T2谱在实用性和评价精度上均略显优势 ;至少是在饱含油的条件下 ,岩心的 NMR T2 谱可以用于研究孔喉结构分布 ,油气的弛豫特性作为影响背景值存在 ,对于评价结果没有明显的影响 ;在全部 6块岩心中 ,T2 与 Pc 的转换系数位于 2 5 0 0～ 4 0 0 0μs· MPa之间。     

Effect of deformation route on microstructural development in aluminum processed by equal channel angular extrusion

Aluminum has been deformed by equal channel angular extrusion (ECAE) to obtain submicron-grained structures under different deformation routes. The deformation routes were varied by rotating billets through 0, 90, and 180 deg between each extrusion pass, and were designated as route A, B_C, and C, respectively. Based on quantitative microstructural analysis, the effectiveness of the deformation route is shown to depend upon the different definition used. The order of effectiveness is (a) A > B_C > C for both 90 and 120 deg dies, in terms of the generation of high-angle grain boundaries (HAGBs); (b) B_C > C > A for both 90 and 120 deg dies, in terms of the formation of equiaxed shape of grains; and (c) B_C > A > C for 90 deg die and B_C ∼ A > C for 120 die, in terms of reducing grain size. It is suggested that the generation of HAGBs can be related to the accumulation of nonredundant strain, while the shape and orientation of grains may be linked to the shearing patterns of the deformation route.     

Approach for Overcoming Numerical Inaccuracy Caused by Load Discontinuity

It was found that the discontinuity at the end of an impulse will lead to numerical inaccuracy as this discontinuity will result in an extra impulse and thus an extra displacement in the time history analysis. In addition, this extra impulse is proportional to the discontinuity value at the end of the impulse and the size of integration time step. To overcome this difficulty, an effective approach is proposed to reduce the extra impulse and hence the extra displacement. In fact, the novel approach proposed in this paper is to perform a single small time step immediately upon the termination of applied impulse, whereas other time steps can be conducted by using the step size determined from accuracy consideration in period. The feasibility of this approach is analytically explored. Further, analytical results are confirmed by numerical examples. Numerical studies also show that this approach can be applied to other step-by-step integration methods. It seems that to slightly complicate the programming of dynamic analysis codes is the only disadvantage of this approach.     

Applying CIM technology to image factories

Image processing allows the automation of the business transaction, turning “paper factories” into “image factories.” This burgeoning new area of computerization needs new paradigms, theories, and methods to maximize its effectiveness at cutting time and costs. This paper investigates what this new area of computerization can gain from CIM technology. It examines the similarities between the processing of computer images in a paperless business environment and the processing of materials into products in the manufacturing plant. These similarities will allow us to apply mature, well-tested CIM techniques to emerging image factories.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

Wavelength and repetition rate tunable optical pulse source using a chirped fiber Bragg grating and a nonlinear optical loop mirror

We experimentally demonstrate a simple and novel scheme for tunable real-repetition-rate multiplication, based on the combined use of fractional Talbot effect in a linearly tunable chirped fiber Bragg grating (FBG) and cross-phase modulation (XPM) effect in a nonlinear optical loop mirror (NOLM). By tuning the group-velocity dispersion of the chirped FBG fabricated with the S-bending method using a uniform FBG, we obtain high quality pulses at pseudorepetition rates of 20/spl sim/50 GHz from an original 8.5-ps 10-GHz soliton pulse train. We subsequently convert this pseudorate multiplication into a real-rate multiplication using XPM effect in an NOLM. A wavelength tuning is also achieved over a /spl sim/15-nm range.     

Designing better adaptive sampling algorithms for ECG Holtersystems

Let Ψ be any adaptive sampling algorithm that can run in real time on a tapeless multichannel electrocardiogram (ECG) Holter system. Simple methods which can significantly improve Ψ's fidelity are described and their results are compared in this paper. It is shown that by adding some simple tests to Ψ, the signals reconstructed by Ψ can be improved as much as 5.45 dB. It is also shown that under the same data rate, a good data compressor with slowly sampled input ECG is preferable to a bad data compressor with highly sampled input ECG     

Optical imaging of anatomical maps derived from magnetic resonanceimages using time-independent optical sources

Presents a model suitable for computing images of absorption cross sections of thick tissue structures illuminated at near infrared (NIR) wavelengths from tomographic projection data. Image reconstruction is accomplished by solving a system of linear equations derived from transport theory. Reconstruction results using different algebraic solvers are shown for anatomical maps of the breast, derived from magnetic resonance imaging data, containing two simulated pathologies, in which case qualitatively good reconstructions were obtained. Evaluation of magnetic resonance (MR) data to optimize NIR optical tomographic imaging methods and to assess the feasibility of a combined MR-optical measurement scheme is discussed     

新型复合弹簧的研究

提出一种金属圆锥弹簧与橡胶圆锥弹簧复合而成的弹簧．分析表明：它可以应用于弹性耦合激励振动筛和座式直线振动筛。