On techniques for angle compensation in nonideal iris recognition.

The popularity of the iris biometric has grown considerably over the past two to three years. Most research has been focused on the development of new iris processing and recognition algorithms for frontal view iris images. However, a few challenging directions in iris research have been identified, including processing of a nonideal iris and iris at a distance. In this paper, we describe two nonideal iris recognition systems and analyze their performance. The word "nonideal" is used in the sense of compensating for off-angle occluded iris images. The system is designed to process nonideal iris images in two steps: 1) compensation for off-angle gaze direction and 2) processing and encoding of the rotated iris image. Two approaches are presented to account for angular variations in the iris images. In the first approach, we use Daugman's integrodifferential operator as an objective function to estimate the gaze direction. After the angle is estimated, the off-angle iris image undergoes geometric transformations involving the estimated angle and is further processed as if it were a frontal view image. The encoding technique developed for a frontal image is based on the application of the global independent component analysis. The second approach uses an angular deformation calibration model. The angular deformations are modeled, and calibration parameters are calculated. The proposed method consists of a closed-form solution, followed by an iterative optimization procedure. The images are projected on the plane closest to the base calibrated plane. Biorthogonal wavelets are used for encoding to perform iris recognition. We use a special dataset of the off-angle iris images to quantify the performance of the designed systems. A series of receiver operating characteristics demonstrate various effects on the performance of the nonideal-iris-based recognition system.     

Novel combination of orientation measurements and transmission microscopy for experimental determination of grain boundary miller indices in silicon and other semiconductors

The determination of grain boundary planes in multicrystalline material has only been restricted to transmission electron microscope investigations (Jang et al., 1992; Elgat et al., 1985) or to metallograpical investigations of the grain boundary (Randle et al., 1993). The first method is expensive, and both are complex and time consuming in grain boundary preparation. This paper proposes the determination of grain boundary planes in semiconductor wafer by a combined application of Electron Back Scatter Diffraction and Infrared Transmission Microscopy. In particular, the new method is demonstrated with directional solidificated multicrystalline silicon.     

Upper-bound modelization of an ironed three-layered polymer-coated steel strip

Global beverage can and food container consumption is very high, with billions of cans produced annually worldwide. There are several steps in can manufacturing, but ironing is the most crucial. In a previous work (Sellés et al., J Mater Process Technol 202:7–14, 2008), a series of ironing experiments were reported using a new material and an ironing simulator. This material was a three-layered polymer-coated steel, and it was seen that under some process conditions, it survived the ironing process with no damage in any of the three layers. The critical die angle was determined as well as specimen quality surface tests. In this paper, an associated theoretical ironing model is described, using the upper-bound theorem and considering the cases of successful ironing or shaving. It is possible to give insight into how to design a material that irons well. For example, the optimal layer thicknesses are also found.     

Biodegradation of lipids from olive oil mill wastewaters in a stationary basket bioreactor with immobilized Bacillus spp. cells - influence of internal diffusion

The study is focused on the external and internal mass transfers of lipids during their biodegradation process in a bioreactor with stationary basket bed of immobilized Bacillus spp. cells. By means of the lipid mass balance for a single particle of biocatalyst, considering the kinetic model adapted for the immobilized bacterial cells, specific mathematical models have been developed to estimate their mass flows in the liquid boundary layer surrounding the particle and inside the particle. The values of mass flows are significantly influenced by the internal diffusion velocity of lipids and the rate of their consumption, but also by the position inside the basket bed. These influences accumulated led to the appearance of a biological inactive region near the particle centre, its magnitude varying from 1.3 to 49.4% of the overall volume of particles.     

Modelling and characterization of AlN-actuated microcantilevers vibrating in the first in-plane mode

The characterization of the first in-plane mode of aluminum nitride-actuated piezoelectric microcantilevers was carried out by using electrical and optical techniques. The top electrode of the cantilever was specifically designed to allow for an efficient electrical actuation of these in-plane modes. In order to confirm the in-plane nature of the modal vibration, the detection of the electrically induced movement was performed optically with the help of a stroboscopic microscope. In parallel, resonances were also measured electrically by means of an impedance analyzer. The quality factor and the resonant frequencies of the in-plane modes were estimated from the corresponding measurement data when applying both detection techniques. Our results show quality factor values as high as 3,000 for the first in-plane mode in air.     

Iterative performance improvement of fuzzy control systems for three tank systems

This paper suggests the performance improvement of fuzzy control systems (FCSs) for three tank systems using iterative feedback tuning (IFT). The stable design of Takagi–Sugeno–Kang fuzzy controllers is guaranteed by means of a stability theorem based on LaSalle’s global invariant set theorem formulated for a class of multi input-multi output (MIMO) nonlinear processes. An IFT algorithm characterized by setting the step size to guarantee the FCS stability is proposed. The theoretical approaches are applied in a case study that deals with the IFT-based stable design of fuzzy controllers dedicated to the level control of a cylindrical three tank system as a representative MIMO system. A set of experimental results for a laboratory setup illustrates the performance improvement.     

Cover Picture: Closing the Gap Between Self‐Assembly and Microsystems Using Self‐Assembly,Transfer, and Integration of Particles (Adv. Mater. 20/2005)

The cover shows 100 μm diameter glass spheres covered by a grid of hexagonally packed polystyrene beads. Wolf and co‐workers placed the 500 nm diameter polystyrene beads onto the larger spheres using the self‐assembly, transfer, and integration (SATI) process that they report on p. 2438. The cover illustrates the capability of SATI to process uneven surfaces in addition to the planar substrates discussed in the article. The carrier that holds the smaller beads deforms during their transfer onto the larger spheres, so that on the larger spheres patterned “caps” are formed. Using this process, which is compatible with standard microfabrication techniques, a variety of particle assemblies can be achieved.     

Calculating ROI for software product lines

Product line engineering has become an important and widely used approach for efficiently developing portfolios of software products. The idea is to develop a set of products as a single, coherent development task from a core asset base (sometimes called a platform), a collection of artifacts specifically designed for use across a portfolio. This approach produces order-of-magnitude economic improvements compared to one-at-a-time software system development. Because the product line approach isn't limited to specific technical properties of the planned software but rather focuses on economic characteristics, high return on investment has become the anthem of the approach's protagonists. Our software product line cost model can calculate the costs and benefits (and hence the ROI) that we can expect to accrue from various product line development situations. It's also straightforward and intuitive.