Quality of Crude Fish Oil Extracted from Herring Byproducts of Varying States of Freshness

ABSTRACT: Herring byproducts were stored at 2 and 15 °C for up to 72 h. Over time, significant increases of total volatile bases (TVB), histamine, putrescine, cadaverine, and tyramine were detected. However, only tyramine and TVB levels were temperature-dependent. The level of total polyunsaturated fatty acids (PUFAs) was constant. Longer byproducts storage gave rise to an oil with higher levels of free fatty acids, eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA), and total PUFAs, while fluorescent compounds were lower. A higher storage temperature led to oil higher in α-tocopherol and EPA levels and lower in anisidine value. Surprisingly, the oil with the highest content of PUFAs was not produced from the freshest byproducts, and oil with low oxidation products can be extracted from stored byproducts.     

Effect of orienting fields on agglomeration in dilute dispersions of magnetic fine particles

Static light scattering was used to investigate dilute dispersions of fine gamma -Fe/sub 2/O/sub 3/ magnetic particles. The particles were acicular and on average 0.39 mu m long and 0.056 mu m in diameter. They were dispersed in organic solvents at concentrations of approximately 10/sup -4/ vol%, corresponding to an average interparticle separation of 9 mu m. Computer programs using a coupled dipole algorithm to predict the scattering from the particles were written. Experimental results do not agree with computer calculations of the light scattering from single particles, but are consistent with scattering from thick ropelike agglomerates of particles. The size of these agglomerates was estimated after 10 s to be less than 100 particles, while the thickness of the ropes is at least 5 particles.<>     

Dynamic control of the permanent magnet-assisted reluctance synchronous machine

A digital signal processor-based control system for the permanent magnet-assisted reluctance synchronous machine, with the emphasis on dynamic performance, is proposed. A classical design approach is used to design the current and speed controllers for the machine. The stator current of the machine is controlled in such a way that the current angle in the dq synchronous reference frame is constant. The load-torque is estimated using a state space observer and compensation current based on the estimated load is used to improve the dynamic performance of the drive. The control system design is machine specific as it relies on data from finite-element analysis. Simulated and measured results on a 110-kW power level show that the resulting control system is stable and robust with good dynamic performance     

Probing the thermal decomposition process of layered double hydroxides through in situ <Superscript>57</Superscript>Fe Mössbauer and in situ X-ray diffraction experiments

The thermal decomposition properties of Mg–Fe hydrotalcites were studied through in situ ⁵⁷Fe Mössbauer spectroscopy and in situ X-ray diffraction. Abrupt changes in the quadrupolar splitting measured in the Mössbauer spectra revealed a phase transition from the starting lamellar structure to a new crystalline arrangement. By analyzing the Mössbauer parameters we show that the material is highly disordered in the 300–400 °C temperature range. This hypothesis is confirmed by the X-ray results whose diffractograms indicated the collapse of the lamellar structure and the formation of a solid solution.     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

The hypersonic environment: Required operating conditions and design challenges

Hypersonic flight powered by airbreathing engines offers the potential for faster response time at long ranges, and reduced cost for access-to-space. In the present paper the operating environment of typical hypersonic vehicles are discussed, including results for the radiation equilibrium wall temperature of external vehicle surfaces and the flow properties through three sample engines spanning the range of hydrocarbon-fueled Mach 4-8 flight and hydrogen-fueled flight at speeds up to Mach 17. Flow conditions at several locations through the sample engines were calculated to provide indications of the required operating flow environment. Additional system consideration such a seals, joints, vehicle integration and in-service engineering are addressed.     

Atmospheric corrosion of reference metals in Antarctic sites

This paper presents the results obtained at three Antarctic test sites participating in the “Ibero-American Map of Atmospheric Corrosiveness” (MICAT), a project on atmospheric corrosion carried out during the period 1988–1994 at some 70 sites distributed across 12 countries of the Latin-American region, Spain and Portugal. The three Antarctic sites are located near the coastline.The singular climatic characteristics of Antarctic regions are related with the purity of the air, the absence of rainfall and the formation of ice on the metallic surface during an important part of the exposure time. However, electrochemical activity is possible below ice layers. This situation affects the structure and morphology of corrosion product films and the resulting corrosion rates of metallic surfaces.     

Modeling and Analysis of a Long Thin Conducting Stripline

A long thin conducting stripline embedded in a dielectric and centered between two large conducting plates, i.e., the stripline environment, is considered. The stripline is modeled as infinitely long, infinitely thin, and perfectly conducting by first considering a stripline of finite length, thickness, and conductivity in a dielectric layer. Starting from Maxwell's equations and assuming that the current on the stripline is a propagating wave in length direction, asymptotic expressions for the fields inside and in the neighbourhood of the stripline are deduced. These expressions are used to model the stripline in the stripline environment, which leads to a boundary-value problem for the electric potential. This problem is solved by two different approaches, leading to integral equations for the current and for an auxiliary function describing the electric potential. A relation between the current and the auxiliary function is deduced, which is used to obtain asymptotic expressions for current and impedance. Results are compared with a numerical solution of the integral equation for the current and with results in literature.     

From biological inspiration toward next-generation manipulators: manipulator control focused on human tasks

This paper presents our approach to extend the niche of behavior-based robotics toward manipulation. We use results from neuroscience to derive some qualitative design rules for the mechanics of the manipulator, resulting in a next-generation manipulator, the "soft arm". By defining the basic behaviors of the manipulator as trajectory-producing behaviors (which is also biologically plausible), we have designed a first test case: writing on a board with a mobile manipulator. The soft arm has not yet been developed; therefore, we have emulated such a soft robot arm on an industrial robot.