Phase Distribution and Magnetic Properties of Mechanically Alloyed Hard/Soft Ferrite Nanocomposites

Improvement in the magnetic properties of hard/ soft ferrite nanocomposites was studied by varying the composition of the soft phase in SrFe₁₂O₁₉/Ni_0.5Zn_0.5Fe₂O₄ nanocomposites. The SrFe₁₂O₁₉/Ni_0.5Zn_0.5Fe₂O₄ nanocomposites were prepared using the mechanical alloying method. The samples were prepared by varying the amount of the soft phase from 10 to 50 wt% while the amount of the hard phase remained 100 wt% in the ferrite nanocomposites. X-ray diffraction (XRD), a vibrating sample magnetometer (VSM), and a transmission electron microscope (TEM) were used to characterize the samples. From the result, it was found that the nanocomposite magnet with 10 wt% of soft phase content had the highest remanence ratio, M _r / M _s , which was 0.61, while the values of the coercivity, H _c , and magnetization, M _s , measured were 4482.4 G and 9.71 emu/g, respectively, and the average particle size of the ferrite nanocomposites was < 50 nm for all the samples. It was also shown that H _c decreased as the weight percent of the soft ferrite increased, which resulted from the dipolar interaction that occurred in the ferrite nanocomposites, showing the effect of phase distribution on the magnetic properties.     

Optimal locations of on-line and off-line rework stations in a serial production system

The production rate and product quality are two vital concerns for any manufacturing industry. Number of defective items reduces production rate and increases unit production cost. Moreover, if nonconforming items reach to the customers then manufacturer’s goodwill may drastically go down. Thus, quality inspection is treated as an inherent part of manufacturing. In this research, an N-stage serial production line with an inspection station at the end of it is considered to make decisions concerning this issue. On detecting a defective item at the end of the line it is scrapped or repaired at regular workstation or is sent to an off-line rework station for repair. Assuming each workstation produces a single type of defect a unit cost function is developed for alternative decisions on each type of defect. In order to minimise the unit cost of production and determine an appropriate decision for individual defect types, a fractional mixed integer nonlinear programming is formulated. After transformation to a mixed integer linear programming problem it is solved optimally. A small problem from garments industry is described in detail to show the solution procedure with a branch and bound method. Empirical tests with up to 40 workstations are permed to show the efficiency of the solution process.     

Topological alternate centrality measure capturing drug targets in the network of MAPK pathways

A new centrality of the nodes in the network is proposed called alternate centrality, which can isolate effective drug targets in the complex signalling network. Alternate centrality metric defined over the network substructure (four nodes – motifs). The nodes involving in alternative activation in the motifs gain in metric values. Targeting high alternative centrality nodes hypothesised to be destructive free to the network due to their alternative activation mechanism. Overlapping and crosstalk among the gene products in the conserved network of MAPK pathways selected for the study. In silico knock‐out of high alternate centrality nodes causing rewiring in the network is investigated using MCF‐7 breast cancer cell line‐based data. Degree of top alternate centrality nodes lies between the degree of bridging and pagerank nodes. Node deletion of high alternate centrality on the centralities such as eccentricity, closeness, betweenness, stress, centroid and radiality causes low perturbation. The authors identified the following alternate centrality nodes ERK1, ERK2, MEKK2, MKK5, MKK4, MLK3, MLK2, MLK1, MEKK4, MEKK1, TAK1, P38alpha, ZAK, DLK, LZK, MLTKa/b and P38beta as efficient drug targets for breast cancer. Alternate centrality identifies effective drug targets and is free from intertwined biological processes and lethality.Inspec keywords: biochemistry, molecular biophysics, cellular biophysics, cancer, drugs, genetics, biomedical materialsOther keywords: MAPK pathways, complex signalling network, pagerank nodes, node deletion, drug targets, MCF‐7 breast cancer cell line‐based data, cellular mechanisms, ERK1 nodes, ERK2 nodes, MEKK2 nodes, MKK5 nodes, MKK4 nodes, MLK3 nodes, MLK2 nodes, MLK1 nodes, MEKK4 nodes, MEKK1 nodes, TAK1 nodes, P38alpha nodes, ZAK nodes, DLK nodes, LZK nodes, MLTKa/b nodes, P38beta nodes     

Inorganic-Based Printed Thermoelectric Materials and Devices

One of the simplest ways to generate electric power from waste heat is thermoelectric (TE) energy conversion. So far, most of the research on thermoelectrics has focused on inorganic bulk TE materials and their device applications. However, high production costs per power output and limited shape conformity hinder applications of state-of-the-art thermoelectric devices (TEDs). In recent years, printed thermoelectrics has emerged as an exciting pathway for their potential in the production of low-cost shape-conformable TEDs. Although several inorganic bulk TE materials with high performance are successfully developed, achieving high performance in inorganic-based printed TE materials is still a challenge. Nevertheless, significant progress has been made in printed thermoelectrics in recent years. In this review article, it is started with an introduction signifying the importance of printed thermoelectrics followed by a discussion of theoretical concepts of thermoelectricity, from fundamental transport phenomena to device efficiency. Afterward, the general process of inorganic TE ink formulation is summarized, and the current development of the inorganic and hybrid inks with the mention of their TE properties and their influencing factors is elaborated. In the end, TEDs with different architecture and geometries are highlighted by documenting their performance and fabrication techniques.     

Infrared Spectroscopy-Based Chemometric Analysis for Lard Differentiation in Meat Samples

One of the most pressing concerns for the consumer market is the detection of adulteration in meat products due to their preciousness. The rapid and accurate identification mechanism for lard adulteration in meat products is highly necessary, for developing a mechanism trusted by consumers and that can be used to make a definitive diagnosis. Fourier Transform Infrared Spectroscopy (FTIR) is used in this work to identify lard adulteration in cow, lamb, and chicken samples. A simplified extraction method was implied to obtain the lipids from pure and adulterated meat. Adulterated samples were obtained by mixing lard with chicken, lamb, and beef with different concentrations (10%–50% v/v). Principal component analysis (PCA) and partial least square (PLS) were used to develop a calibration model at 800–3500 cm⁻¹. Three-dimension PCA was successfully used by dividing the spectrum in three regions to classify lard meat adulteration in chicken, lamb, and beef samples. The corresponding FTIR peaks for the lard have been observed at 1159.6, 1743.4, 2853.1, and 2922.5 cm⁻¹, which differentiate chicken, lamb, and beef samples. The wavenumbers offer the highest determination coefficient R² value of 0.846 and lowest root mean square error of calibration (RMSEC) and root mean square error prediction (RMSEP) with an accuracy of 84.6%. Even the tiniest fat adulteration up to 10% can be reliably discovered using this methodology.     

Royal Crown Shaped Polarization Insensitive Perfect Metamaterial Absorber for C-, X-, and Ku-Band Applications

This study proposed a new royal crown-shaped polarisation insensitive double negative triple band microwave range electromagnetic metamaterial absorber (MA). The primary purpose of this study is to utilise the exotic characteristics of this perfect metamaterial absorber (PMA) for microwave wireless communications. The fundamental unit cell of the proposed MA consists of two pentagonal-shaped resonators and two inverse C-shaped metallic components surrounded by a split ring resonator (SRR). The bottom thin copper deposit and upper metallic resonator surface are disjoined by an FR-4 dielectric substrate with 1.6 mm thickness. The CST MW studio, a high-frequency electromagnetic simulator has been deployed for numerical simulation of the unit cell in the frequency range of 4 to 14 GHz. In the TE mode, the offered MA structure demonstrated three different absorption peaks at 6.85 GHz (C-band), 8.87 GHz (X-band), and 12.03 GHz (Ku-band), with 96.82%, 99.24%, and 99.43% absorptivity, respectively. The electric field, magnetic field, and surface current distribution were analysed using Maxwell’s-Curl equations, whereas the angle sensitivity was investigated to comprehend the absorption mechanism of the proposed absorber. The numerical results were verified using the Ansys HFSS (high-frequency structure simulator) and ADS (advanced design system) for equivalent circuit models. Moreover, the proposed MA is polarisation and incident angle independent. Hence, the application of this MA can be extended to a great extent, including airborne radar applications, defence, and stealth-coating technology.     

Harmonic modification and data adaptive filtering based approach to robust pitch estimation

A novel and robust pitch estimation method is presented in this paper. The basic idea is to reshape the speech signal using a combination of the dominant harmonic modification (DHM) and data adaptive time domain filtering techniques. The noisy speech signal is filtered within the ranges of fundamental frequencies to obtain the pre-filtered signal (PFS). The dominant harmonic (DH) of the PFS is determined and enhanced its amplitude. Normalized autocorrelation function (NACF) is applied to that modified signal. Then empirical mode decomposition (EMD) based data adaptive time domain filtering is applied to the NACF signal. Partial reconstruction is performed in EMD domain. The pitch period is determined from the partially reconstructed signal. The experimental results show that the proposed method performs better than the other recently developed methods for noisy and clean speech signals in terms of gross and fine pitch errors.     

A conditional purpose-based access control model with dynamic roles

This paper presents a model for privacy preserving access control which is based on variety of purposes. Conditional purpose is applied along with allowed purpose and prohibited purpose in the model. It allows users using some data for certain purpose with conditions. The structure of conditional purpose-based access control model is defined and investigated through dynamic roles. Access purpose is verified in a dynamic behavior, based on subject attributes, context attributes and authorization policies. Intended purposes are dynamically associated with the requested data object during the access decision. An algorithm is developed to achieve the compliance computation between access purposes and intended purposes and is illustrated with Role-based access control (RBAC) in a dynamic manner to support conditional purpose-based access control. According to this model, more information from data providers can be extracted while at the same time assuring privacy that maximizes the usability of consumers’ data. It extends traditional access control models to a further coverage of privacy preserving in data mining atmosphere. The structure helps enterprises to circulate clear privacy promise, to collect and manage user preferences and consent.     

Numerical method using cubic B-spline for the heat and wave equation

In the present paper, the cubic B-splines method is considered for solving one-dimensional heat and wave equations. A typical finite difference approach had been used to discretize the time derivative while the cubic B-spline is applied as an interpolation function in the space dimension. The accuracy of the method for both equations is discussed. The efficiency of the method is illustrated by some test problems. The numerical results are found to be in good agreement with the exact solution.