Thermodynamic stability of GaInSb,InAsSb, and GaInP epitaxial films

The miscibility gaps and the critical temperatures of spinodal decomposition of ternary semiconducting Ga-In-Sb, Ga-In-P, and In-As-Sb systems are calculated by taking into account the deformation energy and the effect of plastic relaxation caused by the misfit dislocations. It is shown that taking into consideration elastic energy narrows the ranges of spinodal decomposition and lowers its critical temperature. The introduction of the phenomenological parameter into Matthews-Blakeslee formula makes it possible to reach a satisfactory agreement between theoretically calculated values of critical thickness of epitaxial films and the experimental data.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Graphitization of porous 6H-SiC layers during thermal treatment in vacuum

We have studied the effect of thermal treatment in vacuum on the optical transmission of 6H-SiC samples with a porous layer on the Si face in the visible and near infrared spectral range. An analysis of changes in the absorption coefficient shows that the process of graphitization begins at a temperature below 70°C.     

High-efficiency LEDs of 1.6–2.4 µm spectral range for medical diagnostics and environment monitoring

High efficient LED structures covering the spectral range of 1.6–2.4 μm have been developed on the basis of GaSb and its solid solutions. The electroluminescent characteristics and their temperature and current dependences have been studied. The radiative and nonradiative recombination mechanisms and their effect on the quantum efficiency have been investigated. A quantum efficiency of 40–60% has been obtained in the quasi-steady mode at room temperature. A short-pulse optical power of 170 mW was reached. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 37, No. 8, 2003, pp. 996–1009. Original Russian Text Copyright ? 2003 by Stoyanov, Zhurtanov, Astakhova, Imenkov, Yakovlev.     

An effective compact analyzer of electron spin polarization

A compact electron polarimeter employing the classical Mott scheme has been developed and tested. The device has an efficiency of about 5.6×10⁻⁴, a maximum count rate of 5×10⁵ cps, dimensions 15 cm (diameter) × 25 cm (length), and a working voltage of 40 kV. The polarimeter can operate for a long time under arbitrary vacuum conditions without maintenance, exhibiting no changes in the main working characteristics, and obeys all requirements to the electron spin polarization studies on the modern level.     

Some Specific Features of Degradation of Superheater Tubes of the Boilers of Thermal Electric Power Plants Made of 12Kh18N12T Steel

We study the process of degradation and damage for superheater tubes of the pressure boilers of power plants made of austenitic chromium-nickel steel. The role of sensitization and partial sigmatization of austenitic steel in the embrittlement of the tubes is analyzed.__________Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 40, No. 4, pp. 81–86, July–August, 2004.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Electronic properties of magnetically doped nanotubes

Effect of doping of carbon nanotubes by magnetic transition metal atoms has been considered in this paper. In the case of semiconducting tubes, it was found that the system has zero magnetization, whereas in metallic tubes the valence electrons of the tube screen the magnetization of the dopants: the coupling to the tube is usually antiferromagnetic (except for Cr).     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.