Crystallization and melting behaviour of poly(butylene terephthalate) in poly(butylene terephthalate)/polyarylate blends

Summary The crystallization and melting behaviour of poly(butylene terephthalate) has been studied in the pure state and in its blends with a polyarylate of bisphenol A and isophthalic/terephthalic acids. Differential scanning calorimetry has been used as experimental technique and the effects of different thermal treatments have been analyzed. Results show the hindrance for the crystallization of poly(butylene terephthalate) imposed by the presence of polyarylate, as well as the existence of multiple melting after isothermal crystallization. Explanations are given for the observed behaviours.     

The influence of preparation conditions on the electrochemical behaviour of CuO in a Li/CuO cell

A dozen CuO samples prepared under various conditions and from different starting materials were evaluated as cathode materials for a primary Li/CuO cell. The “thin electrode” method was used for rapid evaluation of the samples. Both coulombic efficiency and discharge voltage depend considerably on the method of synthesis. No correlation was found between the specific surface area and the resistivity of the samples on the one hand and the cathode performance on the other. Best results were obtained from CuO prepared by the oxidation of Cu₂O under controlled temperature and time of oxidation.     

Adjuvant arthritis: influence of the adjuvant volume and composition on the non-specific inflammation

Adjuvant-induced arthritis is an animal model of chronic inflammatory disease widely used in anti-inflammatory and immunosuppressive drugs testing. When the development and the inhibition of the induced arthritis are measured by the injected paw oedema, it is difficult to delineate the immunological contribution from the persistent non-specific primary section. To study the influence of volume and composition of the injected adjuvant upon the primary non-specific inflammation, we devised a 3X4 factorial experiment on a strain of inbred rats with a low susceptibility to adjuvant-induced arthritis. The injection of mineral oil alone produces a persistent oedema. The injection of mycobacteriae in suspension in saline induces a rapid inflammatory response followed by a fast decrease of the oedema. When complete adjuvant is used, there is always a very strong interaction between the effects of the two components of the adjuvant, i.e. the measured oedemas are much greater than the calculated values, For a given injected volume, the inflammation is maximum when the concentration of mycobacteriae is 2.5 mg/ml. All the rats injected with complete adjuvant present a transient oedema of the non-injected hind paw. This oedema is very small and proportional to the amount of mycobacteria injected.     

Hindered and compression settling: parameter measurement and modelling.

The Vesilind settling velocity function forms the basis of flux theory used both in state point analysis (for design and capacity rating) and one-dimensional dynamic models (for dynamic process modelling). This paper proposes new methods to address known shortcomings of these methods, based on an extensive set of batch settling tests conducted at different scales. The experimental method to determine the Vesilind parameters from a series of bench scale settling tests is reviewed. It is confirmed that settling cylinders must be slowly stirred in order to represent settling performance of full scale plants for the whole range of solids concentrations. Two new methods to extract the Vesilind parameters from settling test series are proposed and tested against the traditional manual method. Finally, the same data set is used to propose an extension to one-dimensional (1-D) dynamic settler models to account for compression settling. Using the modified empirical function, the model is able to describe the batch settling interface independently of the number of layers.     

Stoichiometric dye-binding procedure for the determination of the reactive lysine content of soya bean protein

A new analytical method has been developed for the determination of the reactive lysine content of soya bean protein. The method is based on the reaction of the free basic groups of the protein with 1-phenylazo-2 naphthol-6,8 disulphonic acid. With regard to the stoichiometry of the procedure, it has been proved, contrary to earlier reports, that the basic amino acids, histidine, arginine and lysine, each combine with one mole of the dye. After acylation with propionic anhydride lysine alone loses its dye reactivity. The usefulness of the proposed method has been demonstrated by the determination of the reactive lysine content of several untreated, heat-treated and acid-treated soya bean samples. The results show that heat damage of about 5% in reactive lysine content can be measured in 1·5 h with good reproducibility.