Noise spectroscopy: Z-determination by statistical count-rate analysis (Z-scan)

We introduce Noise Spectroscopy (NS) and show the results of an analysis of three data-sets demonstrating the feasibility of this technique. The NS effect is first shown to be present in a set of X-ray radiography images of low- and high-Z materials taken using the 6 MV Rapiscan Eagle P60HP portal cargo inspection system. Image-Based NS is, however, relatively insensitive. Using a data-set obtained using a fast plastic scintillator and photo-multiplier tube (PMT), we demonstrate that NS works very well when using fast detectors, fast electronics and waveform digitization. Another data-set was taken using Lutetium-Yttrium Ortho-Silicate (LYSO), which is suitable for use in X-ray cargo radiography. Although LYSO is slower than plastic scintillator, it was shown that NS also works very well using this material, paving the way for NS to be implemented using the primary imaging array of X-ray cargo inspection systems.     

Grain Floatation During Equiaxed Solidification of an Al-Cu Alloy in a Side-Cooled Cavity: Part I—Experimental Studies

Experimental studies were performed to investigate the role and influence of grain movement on macrosegregation and microstructure evolution during equiaxed solidification. Casting experiments were performed with a grain-refined Al-Cu alloy in a rectangular sand mold. For the aluminum alloy studied, the equiaxed grains are lighter than the bulk melt and thus float up. Experiments were designed to investigate floatation phenomena of equiaxed grains in the presence of thermosolutal convection. Cooling curves were recorded at key locations in both the casting and the chill. Quantitative image analysis and spatial chemical analysis were performed on the solidified casting to observe the chemical and microstructural inhomogeneity created by the melt convection and solid floatation. Several notable features that can be attributed to grain movement were observed in temperature histories, macrosegregation patterns, and microstructures. In our experiments, the floatation of grains influences the thermal conditions and the overall flow direction in the casting cavity. In some cases, the induced flow resulting from the grain movement caused a flow reversal. This in turn influences the solidification direction, microstructure evolution, and the overall macrosegregation behavior.     

Detection of Axial Cracks in Pipes Using Focused Guided Waves

The implementation of synthetic guided wave focusing to locate axially aligned defects in pipes has been investigated. Results from both finite element computer models and experiments on real pipes are presented and the data show good agreement. Focusing is necessary to improve the reflection coefficient from axially aligned defects, as the signals are very weak. The Common Source Method (CSM) of synthetic focusing has been applied which makes it possible to apply focusing via post processing to previously collected data. The dependence of reflection coefficient on crack length was measured for both through thickness and part depth axially aligned defects, at a range of frequencies, using the torsional guided wave family. The results show that the reflection coefficient is approximately doubled when focusing is employed, compared to the sensitivity for unfocused fundamental torsional waves. However the sensitivity is still very low, so in practise this approach could only be used to find severe defects.     

Dynamic construction site layout planning using max-min ant system

Construction site layout planning (CSLP) is a dynamic multi-objective optimization (MOO) problem as there are different facilities employed in the different construction phases of a construction project. In this study, a new method using continuous dynamic searching scheme to guide the max-min ant system (MMAS) algorithm, which is one of the ant colony optimization (ACO) algorithms, to solve the dynamic CSLP problem under the two congruent objective functions of minimizing safety concerns and reducing construction cost is proposed. Using weighted sum method the MOO problem can be solved by the proposed MMAS method. An office building case was used to verify the capability of the proposed method to solve dynamic CSLP problem and the results are promising. The approach could be benchmarked by researchers using other advanced optimization algorithms to solve the same problem or expand the applications to other fields.     

Megasonic agitation for enhanced electrodeposition of copper

In this paper we propose an agitation method based on megasonic acoustic streaming to overcome the limitations in plating rate and uniformity of the metal deposits during the electroplating process. Megasonic agitation at a frequency of 1 MHz allows the reduction of the thickness of the Nernst diffusion layer to less than 600 nm. Two applications that demonstrate the benefits of megasonic acoustic streaming are presented: the formation of uniform ultra-fine pitch flip-chip bumps and the metallisation of high aspect ratio microvias. For the latter application, a multi-physics based numerical simulation is implemented to describe the hydrodynamics introduced by the acoustic waves as they travel inside the deep microvias.     

Motivation,commitment and the use of incentives in partnerships and alliances

The use of incentives in partnering and alliancing has been seen as an important way of reinforcing collaboration in the short term and helping to build trust between clients and contractors in the long term. Yet only rarely has the impact of incentives on such relationships been discussed, let alone subjected to systematic investigation. This is despite a wealth of theory and research which brings into question the use of incentives and reinforcers as ways of generating motivation and commitment. Drawing upon this theoretical knowledge base and using evidence from a number of case studies of partnerships and alliances, this paper demonstrates how a number of important cognitive and social dimensions affect the use and impact of incentives, sometimes in ways contrary to those intended. The conclusion drawn is that there are important limitations to the use of incentives as means of reinforcing collaboration and developing commitment and trust, and that this raises questions more generally about the assumptions that underlie many of the practical ‘tools and techniques’ commonly associated with partnering and alliancing.     

A family of parallel QR factorization algorithms

Rapid computation of the QR factorization of a matrix is fundamental to many scientific and engineering problems. The paper presents a family of algorithms parameterized by the number of processors available P, arithmetic grain aggregation parameters g₁, g₂, …, g_P, and communication grain aggregation parameter h, which computer the QR factorization of a matrix A ∈ C^{m × n} with minimal latency. The approach is particularly well suited for dedicated distributed memory architectures such as linear arrays of INMOS Transputers, Texas Instruments C40s or Analog Devices 21060s.     

Polynomial methods for the structured singular value with real parameters

We consider the structured singular value problem with real parametric uncertainty only. Using techniques from algebraic geometry, we propose two algorithms that in principle can yield the precise value of the structured singular value at a fixed frequency. Their ability to do so depends upon their ability to find all common roots to a system of polynomial equations. The first algorithm is applicable to problems with two real parameters each of multiplicity two. The second algorithm is applicable to problems with n distinct real parameters. These algorithms have proved useful in applications to aerospace control law analysis.