实验室条件下聚能射孔损害带研究

在实验室条件下对贝雷砂岩进行射孔试验,并分别对射孔后的靶体进行酸化、压裂工艺处理,利用核磁共振和工业X-CT技术分别对未射孔的靶体、射孔后的靶体、射孔后酸化的靶体、射孔后压裂的靶体进行测试.定量分析了射孔对砂岩靶体的损害及酸化、压裂对射孔损害的解除作用.     

A Nonvolatile Organic Memory Device Using ITO Surfaces Modified by Ag‐Nanodots

We report on a single‐layer organic memory device made of poly(N‐vinylcarbazole) embedded between an Al electrode and ITO modified with Ag nanodots (Ag‐NDs). Devices exhibit high ON/OFF switching ratios of 10⁴. This level of performance could be achieved by modifying the ITO electrodes with some Ag‐NDs that act as trapping sites, reducing the current in the OFF state. Temperature dependence of the electrical characteristics suggest that the current of the low‐resistance state can be attributed to Schottky charge tunnelling through low‐resistance pathways of Al particles in the polymer layer and that the high‐resistance state can be controlled by charge trapping by the Al particles and Ag‐NDs.     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

储层压力与天然气分布关系——以鄂北塔巴庙地区上古生界储层为例

通过分析塔巴庙地区储层压力的分布特征，建立了研究区泥岩压实曲线，并对影响和控制该区储层压力的主要因素和机理进行了探讨，对“欠压实”剩余压力、生气增压、抬升引起的降压进行了定量计算。分析结果表明，晚三叠-早白垩世末“欠压实”作用和晚侏罗-早白垩世末烃源岩大量生烃作用使塔巴庙地区上古生界形成异常高压；晚白垩系构造抬升降压，使得现今储层为正常-低异常压力。同时证实了“欠压实”对天然气有压力封盖作用，天然气都分布在最大“欠压实”幅度以下的储层当中。烃源岩生气高峰为晚侏罗-早白垩世末，但天然气大规模运移是在晚白垩世，方向以沿过剩压力梯度降低较快的方向（太原-山西组至下石盒子组）垂向运移，通道主要为裂缝，运移的动力主要为异常高压。由于储层致密，聚集成藏能量有限，造成天然气充注不足、气水分异不好、含气饱和度低。     

甘油三乙酸酯超临界酯交换反应及其动力学研究

研究了在超临界条件下甘油三乙酸酯与甲醇或乙醇的酯交换反应,分别考察了超临界状态下醇油摩尔比和温度对反应的影响。实验结果表明,甲醇或乙醇与甘油三乙酸酯的摩尔比为14、反应温度为350℃、反应时间为20m in时,乙酸甲酯或乙酸乙酯的收率分别达100%和60%。对超临界状态下动力学的研究结果表明,甘油三乙酸酯与甲醇或乙醇的酯交换反应为拟一级反应,在相同的反应条件下,采用甲醇时酯交换反应速率比用乙醇时快,相应的甘油三乙酸酯的转化率也高;甘油三乙酸酯在超临界甲醇或乙醇中酯交换反应的表观活化能分别为58.7 kJ/mol和75.1 kJ/mol,甘油三乙酸酯与甲醇酯交换反应的活化能低于与乙醇酯交换反应的活化能,表明碳链短的醇更易进行酯交换反应。     

数控超声加工的初步工艺试验

介绍在经过数控化改造的两坐标超声加工机床上所进行数控超声加工的初步工艺试验,并讨论试验结果。     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

高分辨率合成孔径雷达图像舰船检测方法

寻找针对高分辨率SAR图像的舰船目标检测算法。利用KSW双阈值分割技术，其效果比传统检测方法好，有利于进一步的目标分类和识别。且必须根据SAR图像分辨率来选择舰船检测算法。     

CDMA发射分集系统的多用户检测常模算法分析

空时分集技术的最大优点在于在不增加带宽的情况下可以提高系统的可靠性,是目前移动通信的研究热点.常模算法是一种性能优良的码分多址(CDMA)盲多用户检测技术,能确保判决信号与实际传送信号之间的差错较小,误码率性能良好.文中提出将标准线性受限常模算法(LCCMA)与空时分组码(STBC)相结合,设计出一种收敛快、能够改善系统性能的基于2-空时分组码的多用户接收机.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.