Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

智能电动机控制器在电收尘通风机上的应用

对智能电动机控制器的情况作了介绍，结合工作实践提出了维护要点和建议，并对该控制器的参数设置进行了说明，这对使用该设备的工业企业有一定的指导意义。     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

基于MoCA标准的家庭网络研究

本文描述了一种基于MOCA标准的家庭网络,并对该网络及设备进行了基本性能的测试.本文首先介绍了家庭网络的发展现状,对目前的各种家庭网络标准进行了比较.在此基础上详细描述了基于MOCA标准的家庭网络,并对该网络的设计,实现、网络性能进行了详述.然后对该网络进行了测试并得出了相关的测试结论.最后指出该网络的不足及改进之处.     

偏高岭土的研究现状及展望

简要介绍了偏高岭土的反应机理和在国内外的研究现状。同时对偏高岭土的研究进行了展望 ,提出因麦特林水泥原料丰富 ,污染小 ,加工简单 ,性能优越 ,其应用前景广阔 ,应对其加强研究。     

Experimental Research on Erbium-doped Superfluorescent Fiber Source

The effects of the variations in fiber length, fiber mirror reflectance on efficiency and output power are experimentally investigated for erbium-doped double pass backward superfluorescent fiber sources (SFSs). The influence of fiber length on mean wavelength stability (MWS) has also been demonstrated. By incorporating a short section of un-pumped erbium-doped fiber (EDF) at the output port, the pump power dependent on MWS becomes independent of pumped EDF length. This is a novel phenomenon that hasn‘t been reported up to now,and should be helpful to SFS fabrication and theory analysis. By using a fiber Michelson interferometer as spectrum slicing component,a multi-wavelength fiber source (MWFS) with ～20 channels (from 1542nm to 1559nm) is got. The MWFS has a channel spacing of ～0. 8 nm which satisfies ITUstandard. The intensity fluctuation among channels is less than 0.5dB,and the extinction ratio of all channels is above 14dB. This kind of MWFS should be useful to wavelength division multiplexing systems.     

Frequency domain identification of Wiener models

This paper proposes a frequency domain algorithm for Wiener model identifications based on exploring the fundamental frequency and harmonics generated by the unknown nonlinearity. The convergence of the algorithm is established in the presence of white noise. No a priori knowledge of the structure of the nonlinearity is required and the linear part can be nonparametric.     

SLIMLINE+K型多功能撬装双滚筒试井绞车简介

SLIMLINE K型多功能撬装双滚筒试井绞车为整体式结构，多用于海上平台，可进行电子压力计和机械压力计试井，以及井下工具的投放、震击、打捞等完井作业。该试井绞车采用先进的数控技术，使起下纲丝／电缆实现自动化控制，该系统能够对斜井、定向井进行随钻测试。     

Intelligent Painting Process Planner for Robotic Bridge Painting

Due to increased government regulations on environment, health, and safety, the cost of on-site bridge painting has quadrupled over the past several years. The construction industry faces a great challenge in how to control the increased costs of bridge painting and meet the regulations at the same time. A possible solution to address this challenge is to develop a robotic bridge painting system. The development of the robotic system can be justified by the potential improvements in safety and productivity. This paper presents the development and testing of an Intelligent Painting Process Planner. The Planner, built based on bridge feature scheme, is the key component for the robotic bridge painting system that integrates the painting process planning, robot path planning, cost optimization, and quality control functions. During the development process, lab experiments were conducted to determine the values of painting process planning parameters and coating thickness distribution functions. Field tests demonstrated that the prototype robotic bridge painting system achieved the specified painting quality using the parameter values provided by the Planner. Areas that need to be improved in the future were also identified.     

1/3码的动态CMOS全自检电路的设计

自检测电路设计方法有多种多样,本文中介绍了TSC电路的概念,并采用1/3码的动态CMOS设计TSC电路,通过在Cadence环境下仿真,仿真结果表明本设计可行。